Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Additional assembly options are available for cost or performance optimization upon request.

Block Diagram

Figure 1: TE022-02 block diagram.

Main Components

Figure 2: TE0722-02 PCB top side.

Figure 3: TE0722-02 PCB bottom side.

  1. Xilinx ZYNQ XC7Z010 SoC, U1
  2. Micro SD card socket with card detect, J8
  3. Red LED, D3
  4. Green LED, D2
  5. Red LED, D6
  6. 20-pin connector placeholder, P1
  7. Red LED, D5
  8. Proximity/ambient light sensor, U4
  9. RGB LED, D4
  10. Red LED, D1
  11. 20-pin connector placeholder, P2
  12. Ultra-low supply-current voltage monitor, U4
  13. 2 x 5-pin connector placeholder, J1
  14. 2 x 5-pin connector placeholder, J2
  15. 2 x 5-pin connector placeholder, J3
  16. 16 MByte QSPI Flash memory, U5
  17. Low power programmable oscillator @ 33.333333 MHz, U8
  18. 1A PowerSoC DC-DC converter (1.0V), U2
  19. 1A PowerSoC DC-DC converter (1.8V), U3

Initial Delivery State

Storage device name

Content

Notes

QSPI Flash

Empty

 

Table 1: .

Boot Process

By default the ... supports QSPI and SD Card boot modes which is controlled by the MODE input signal from the B2B connector JM..

...

BankTypeConnectorI/O Signal CountVoltageNotes
34HRP183.3P0 - P7
34HRP283.3P24 - P31
34HRP210, 5 LVDS pairs3.3 
34HRJ163.3X2A - X2F
34HRJ223.3 
34HRJ343.3X1A - X1D
35HRP18, 4 LVDS pairs3.3 

Table 3: .

JTAG Interface

JTAG access to the Xilinx ZYNQ XC7Z010 SoC is provided through J2 connector.

JTAG Signal

J2 Connector Pin

TCK 4
TDI 9
TDO 10
TMS 8

Table 4: .

Default PS MIO Mapping

MIOFunctionConnector PinNotes
0---
1QSPI-SPI Flash-CS
2QSPI-SPI Flash-DQ0
3QSPI-SPI Flash-DQ1
4QSPI-SPI Flash-DQ2
5QSPI-SPI Flash-DQ3
6QSPI-SPI Flash-SCK
7GPIO-Green LED D2
8---
9---
28SD CARDJ8-5CLK
29SD CARDJ8-3CMD
30SD CARDJ8-7DAT0
31SD CARDJ8-8DAT1
32SD CARDJ8-1DAT2
33SD CARDJ8-2CD/DAT3
36I2C-SCL
37I2C-SDA
39GPIO-Si1143 INT pin
49SD CARDJ8-G4Card detect switch

Table 5: .

I2C Interface

On-board I2C interface is provided via Zynq SoC's PS bank 501 pins MIO36 (SCL) and MIO37 (SDA). I2C addresses for on-board devices are listed in the table below:

I2C DeviceSlave AddressNotes
 Si1143-A11-GMR0x5AProximity and ambient light sensor.

Table 6: .

On-board Peripherals

Quad SPI Flash Memory

Oscillators

On-board LEDs

LEDColorConnected ToDescription and Notes
D1RedLED2, U4 
D2

Green

MIO7, U1User controlled, default OFF (when PS7 has not been booted).
D3

Red

LED1, U4

 
D4RGB

RGB_R, U1

RGB_G, U1

RGB_B, U1

 
D5RedLED3, U4 

D6

Green

DONE, U1

Reflects inverted DONE signal. ON when FPGA is not configured,

OFF as soon as PL configuration is finished.

Table 6: .

Power and Power-On Sequence

...

Power InputTypical Current
3.3VTBD*

Table 7: Typical power consumption.

...

Power supply with minimum current capability of 1A for system startup is recommended.

Power-On Sequence

Variants Currently in Production

 Module VariantZynq SoCARM Cores

Operating Temperature

Temperature Range
TE0722-02IXC7Z010-1CLG225I 

–40°C to +85°C

Industrial
TE0722-02XC7Z010-1CLG225I 

0°C to +70°C

Commercial
TE0722-02-07S-1CXC7Z007S-1CLG225C 

0°C to +70°C

Commercial

Table 8: Module variants.

Technical Specifications

Absolute Maximum Ratings

Parameter

MinMax

Units

Reference Document

VIN supply voltage

-0.53.6

V

Xilinx datasheet DS187, "Zynq-7000 All Programmable SoC: DC and AC Switching Characteristics".

Storage temperature

-40

+85

°C

Silicon Labs Si1141/42/43 datasheet.

Table 9: Module absolute maximum ratings.

Recommended Operating Conditions

ParameterMinMaxUnitsReference Document
Supply voltage1.143.465 VXilinx datasheet DS187, "Zynq-7000 All Programmable SoC: DC and AC Switching Characteristics".

Table 10: Module recommended operating conditions.

 

Note
Assembly variants for higher storage temperature range are available on request.

...

 All dimensions are given in millimeters.

 

Figure 4: TE0722-02 physical dimensions.

Operating Temperature Ranges

...

DateRevision

Notes

PCNDocumentation Link
2015-10-2302  TE0722-02
 

01

 

  

Table 11: TE0722 module hardware revision history.

Hardware revision number is printed on the PCB board together with the module model number separated by the dash.

...

Date

Revision

Contributors

Description

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd

Jan Kumann

Initial document.

Table 12: Document change history..

Disclaimer

Include Page
IN:Legal Notices
IN:Legal Notices