Page History
...
| Scroll Only (inline) |
|---|
https://wiki.trenz-electronic.de/display/PD/TEI0004+TRM for the current online version of this manual and other available documentation. |
The Trenz Electronic TEI0004 Arrow USB Programmer2 is an universal USB2.0 adapter board based on the FTDI FT2232H USB2.0 IC. The adapter board converts signals from USB2.0 to the standard serial interfaces JTAG and UART.The board is fully compatible to USB Blaster to program Intel (Altera) FPGA devicesFT2232H based JTAG Adapter supported by Intel Quartus.
Key Features
- Supported by Intel Quartus (JTAG Mode only)
- , Intel JTAG Compatible Pinout
- Additional UART Channel available
- Based on FTDI FT2232H USB2 Interface
- Micro USB Connector
- RED activity LED
- GREEN Power-on LED
Block Diagram
Figure 1: TEI0004-02 Block Diagram.
Main Components
Figure 12: TEI0004-02 main components.
- FTDI FT2232H IC
- RED LED (Activity)
- Green LED (Power-on)
- Micro USB2 Connector
- 2x5-pin female socket JTAG Connector (White dot marks Pin 1)
Signals, Interfaces and Pins
...
The 2x5 female socket have to be connected to the corresponding pin header on the target system. The signal assignment of the pin header on the adapter board is fully compatible to original USB blaster. Furthermore there is also an UART interface available and user configurable I/O pin (usable e.g. as Reset signal)-pin reserved for future use.
Following table describes the pin-assignment to the signals of the interfaces:
| Signal | Pin Number | Pin Number | Signal | |
|---|---|---|---|---|
| TCK (output from adapter) | 1 | 2 | GND | |
| TDO (input to adapter) | 3 | 4 | Reference I/O-voltage of from target board for JTAG and UART | |
| TMS (output from adapter) | 5 | 6 | User | Reserved Output (May be used as Processor Reset in future software releases) |
| UART RX (input to adapter)UART RX | 7 | 8 | UART TX (output from adapter) | |
| TDI (output from adapter) | 9 | 10 | GND |
Table 1: 2x5-pin female socket pin-JTAG Connector pin assignment.
USB Interface
The USB2.0 USB interface is provided by the FTDI FT2232H chip accessible by the Micro USB2.0 B (receptacle) socketIC. The entire USB protocol is handled on chip and compatible to USB2USB 2.0 High Speed (480 MBps) and Full Speed (12 MBps).
On-board Peripherals
FTDI FT2232H IC
The FTDI FT2232H chip provides a variety of industry standard serial or parallel interfaces. On the TEI0004 adapter board the interfaces USB2.0 to JTAG, UART and one user GPIO are available.
Refer to the FTDI data sheet to get information about the capacity of the FT2232H IC.
Configuration EEPROM
The external EEPROM can be used to customize the TEI0004 adapter board by setting numerous parameters of the FT2232H IC, enabling different functionalities and configuring serial or parallel interfaces.
The EEPROM is programmable in-circuit over USB using a utility program called FT_PROG available from FTDI’s web site (www.ftdichip.com)FTDI FT2232H IC Channel A is used in MPPSE Mode for JTAG, Channel B is available as UART. FT2232H EEPROM is programmed with Arrow Programmer2 Identificator to be recognized by the support library for Quartus.
On-board LEDs
On-board LEDs indicating power-on and user dependentJTAG activity:
| Color | Connected to | Description and Notes |
|---|---|---|
| Green | 3.3V | 3.3V power status Power-on LED |
| Red | FTDI IC | user configurableJTAG activity |
Table 2: On-board LEDs.
Power
Power supply of the adapter board
The TEI0004 USB2.0 adapter board Arrow Programmer2 is powered via USB supply voltage on the Micro USB2.0 socket.
Power Rails
...
Power Rail Name
...
2x5-pin Female Socket
...
Direction
...
Table 3: Power rails.
Technical Specifications
Absolute Maximum Ratings
| Parameter | Min | Max | Units | Reference Document |
|---|---|---|---|---|
VREF | -0.5 | 4.6 | V | Nexperia 74AVCH4T245 data sheet |
| USB VBUS | 4.75 | 5.25 | V | USB2USB 2.0 Specification |
| Voltage on I/O pins | -0.5 | 4.6 | V | Nexperia 74AVCH4T245 data sheet |
| Storage temperature | -40 | +90 | °C | LED 19-213/R6C-AL1M2VY/3T data sheet |
Table 43: Board absolute Absolute maximum ratings.
Recommended Operating Conditions
| Parameter | Min | Max | Units | Reference Document | |
|---|---|---|---|---|---|
VREF | 30.08 | 3.6 | V | USB Blaster specification | Nexperia 74AVCH4T245 data sheet |
| USB VBUS | 4.75 | 5.25 | V | USB2USB 2.0 Specification | |
| Voltage on I/O pins | 0 | 3.6VREF | V | Nexperia 74AVCH4T245 data sheet | |
| Operating temperature | -40 | +85 | °C | FTDI FT2232H data sheet |
Table 54: Board recommended Recommended operating conditions.
Operating Temperature Range
Industrial grade: -40°C to +85°C.
The TEI0004 USB2.0 adapter board is capable to be operated at industrial grade temperature range.
Arrow Programmer2 can be used within industrial temperature range.
Physical Dimensions
Module size: 14.2mm × 20.8mm. Please download the assembly diagram for exact numbers.
Highest part on PCB: 7.37 mm. Please download the step model for exact numbers.
All dimensions are given in millimeters and mil.
Figure 3: Physical dimensions drawing.
Revision History
Hardware Revision History
| Date | Revision | Notes | PCN | Documentation Link |
|---|---|---|---|---|
| - | 01 | prototypesPrototypes | - | - |
| - | 02 | current available revisionFirst production release. | - | TEI0004 |
Table 65: Board hardware Hardware revision history.
Hardware revision number can be found on the PCB board together with the module model number separated by the dash.
Figure 24: Board hardware revision Revision number.
Document Change History
...
Date | Revision | Contributors | Description | |||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| modified-date |
| modified-
|
|
|
| ||||||||||||||||||||||||||||
2022-05-05 | v.50 | John Hartfiel |
| |||||||||||||||||||||||||||||||
| 2017-11-23 | v.31 | Ali Naseri | updated block diagram | |||||||||||||||||||||||||||||||
2017-11-21 | v.25 | Ali Naseri |
|
Table 156: Document change history.
...
Overview
Content Tools