Page History
...
HTML |
---|
<!-- Download Link: Go to Base Folder of the Module or Carrier, for example : https://shop.trenz-electronic.de/en/Download/?path=Trenz_Electronic/TE0712 Use english URL "../en/.. --> |
Scroll Ignore |
---|
Download PDF version of this document. |
Scroll pdf ignore | |
---|---|
Table of Contents
|
...
Microsemi SmartFusion2 SoC FPGA
- 8 MByte SDRAM
8 MByte QSPI Flash memory
- 25 MHz system clock and 32.768 KHz auxiliary clock
- JTAG and UART over Micro USB2 USB connector
- 1x 3-pin header for Live Probes
- 1x PMOD header providing 8 GPIOsI/O
2x 14-pin headers (2,54 mm pitch) providing 23 GPIOsI/O
9 user LEDs
- 1 user push button
- 3.3V single power supply with on-board voltage regulators
- Size 61.5 x 25 mm
...
- Microsemi SmartFusion2 FPGA SoC, U5
- 8 Mbyte SDRAM 166MHz, U2
- Micro USB2 B socket (receptacle), J9
- Switch button (reset), S1
- Switch button (user), S2
- Red LED (user), D10
- Green LED (indicating supply voltage), D1
- 8x red LEDs (user), D2 - D9
- FTDI USB2 to JTAG/UART adapterinterface, U3
- 8 Mbyte QSPI Flash memory, U1
- 32.768 KHz auxiliary crystal oscillator, Y1
- 25 MHz main crystal oscillator, Y2
- 1x14 pin header (2.54mm pitch), J2
- 1x6 pin header (2.54mm pitch), J4
- 3-pin header (2.54mm pitch), J3
- 1x14 pin header (2.54mm pitch), J1
- 2x6 Pmod connector, J6
...
Storage device name | Content | Notes |
---|---|---|
Quad SPI Flash (U1) OTP areaEmpty | empty | - |
SPI Flash | empty | - |
I2C Configuration FTDI EEPROM, U9 | Programmed - | FlashPro identification, should not be changed by customer |
Table 1: Initial delivery state of programmable devices on the module
Boot Process
By default the configuration mode pins of the FPGA are set to QSPI mode, hence the FPGA is configured from serial Flash memory at system start-up. The JTAG interface of the module is provided for storing the initial FPGA configuration data to the QSPI flash memoryThere is are no bootmode selection Microchip SmartFusion2 SoC boots always from internal configuration flash, optionally software code for the Cortex-M or soft CPU can be placed to eNVM.
Signals, Interfaces and Pins
...
Bank | VCCIO | I/O's Count | Available on Connectors | Notes |
---|---|---|---|---|
1 | 3.3V | 14 | 5 | 6 I/O's connected to FTDI chip, 1 I/O used for user button S2, 2 I/O's connected to red user LEDs D2 and D10. |
2 | 3.3V | 37 | 26 | 6 I/O's user for QSPI Flash, 5 I/O's connected to red user LEDs D3 ... D7. |
3 | 3.3V | 5 | 5 | Bank 3 is dedicated to JTAG interface. |
4 | 3.3V | 24 | 02 | 2 I/O's are dedicated to live probes, all other I/O's are used as memory interface. |
7 | 3.3V | 22 | 2 | 2 I/O's available on header J2, 2 I/O's connected to red user LEDs D8 and D9, all other I/O's are used as memory interface. |
Table 3: General overview of FPGA I/O banks
JTAG Interface
Primary JTAG access to the FPGA SoC device U5 is provided through Micro USB2 B connector J9. The JTAG interface is created by the implemented with FTDI FT2232H USB2 to JTAG/UART adapter bridge IC U3.
Optionally 1x6 male pin header J4 can be fitted on board for access to the JTAG interface on board. The pin assignment of header J4 is shown on table below:
JTAG Signal | Pin on Header J4 | Note |
---|---|---|
TCK | 3 | - |
TDI | 5 | - |
TDO | 4 | - |
TMS | 6 | - |
JTAGSEL | 2The JTAGSEL pin of SmartFusion2 device depends on the used JTAG programmer. | can be left open for normal operation |
Table 4: optional second JTAG interface or GPIO (JTAGSEL dependent)JTAG header
QSPI Interface
The QSPI interface of the FPGA device is routed to and used by the on-module QSPI flash IC U1:
...
Table 5: QSPI interface signals
Note: On-board SPI Flash is connected to regular FPGA I/O pins, access to it is only possible when using custom SPI flash IP core or via MSS subsystem SPI when it is connected via fabric to those pins. There is no automatic boot from this flash.
On-board Peripherals
Quad SPI Flash Memory
On-module QSPI flash memory (U7) is provided by Winbond Serial Flash Memory W74M64FV with 64 MBit (8 MByte) storage capacity. This non volatile memory is used to store initial FPGA configuration. Besides FPGA configuration, remaining free flash memory can be used for user application and data storage.
SDRAM
The TEM0001 FPGA module is equipped with a Winbond W9864G6JT 64 MBit (8 MByte) SDRAM chip U2. This SDRAM chip is connected to the FPGA bank 4 and 7 via 16-bit memory interface with 166MHz clock frequency and CL3 CAS latency.
FTDI FT2232H IC
The FTDI chip U3 converts signals from USB2.0 to a variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip.
FTDI FT2232H chip is used in MPPSE mode for JTAG, 6 I/O's of Channel B are routed to the bank 1 of the FPGA SoC and are usable for example as UART interfaceFTDI FT2232H Channel A works as JTAG interface compatible to Libero tools. Channel B is connected to FPGA pins with direct access to MSS UART peripheral.
The configuration of FTDI FT2232H chip is pre-programmed on to the EEPROM U9 to make it work as FlashPro5 interface for Libero tools.
System Clock Oscillator
The FPGA SoC module has following reference clocking signals provided by on-board oscillators:
Clock Source | Schematic Name | Frequency | Clock Input Destination |
---|---|---|---|
Microchip MEMS Oscillator, U7 | CLK12M | 12.0000 MHz | FTDI FT2232 U3, pin 3; FPGA SoC bank 2, pin N16 |
ECS SMD Crystal Oscillator, Y1 | - | 32.768 KHz | FPGA SoC U5 auxiliary clock input, pin pins W17/Y17 |
AVX Quartz Crystal Oscillator, Y2 | - | 25.000 MHz | FPGA SoC U5 main clock input, pin pins W18/Y18 |
Table 6: Clock sources overview
...
LED | Color | Signal Schematic Name | FPGA | Notes |
---|---|---|---|---|
D1 | Green | - | - | Indicating 3.3V board supply voltage |
D2 | Red | 'LED1' | E18 | user |
D3 | Red | 'LED2' | R17 | user |
D4 | Red | 'LED3' | R18 | user |
D5 | Red | 'LED4' | T18 | user |
D6 | Red | 'LED5' | U18 | user |
D7 | Red | 'LED6' | R16 | user |
D8 | Red | 'LED7' | E1 | user |
D9 | Red | 'LED8' | D2 | user |
D10 | Red | 'USER_LED' | G17 | user |
Table 7: LEDs of the module
...
Button | Signal Schematic Name | FPGA | Notes |
---|---|---|---|
S1 | 'USER_BTN' | B19 | user configurable |
S2 | 'RESET' | E18U17 | system reset (reconfiguration) |
Table 8: Push buttons of the module
...
Date | Revision | Notes | PCN | Documentation Link |
---|---|---|---|---|
- | 01 |
| - | TEM0001-01 |
Table 12: Module hardware revision history
...
Date | Revision | Contributors | Description | ||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
|
| ||||||||||||||||||||||
v.33 | Antti Lukats |
| |||||||||||||||||||||||
2018-04-17 | v.31 | Ali Naseri |
|
Table 13: Document change history
...