Page History

Overview

Microblaze Design with linux example.

Refer to http://trenz.org/te0710-info for the current online version of this manual and other available documentation.

For directly getting started with the prebuilt files jump to the section Launch.

Key Features

Revision History

Release Notes and Know Issues

Requirements

Software

Hardware

Page properties
hidden true id Comments
Notes :

Basic description of TE Board Part Files is available on TE Board Part Files.

Complete List is available on "<project folder>\board_files\*_board_files.csv"

Design supports following modules:

Design supports following carriers:

Additional HW Requirements:

Content

For general structure and usage of the reference design, see Project Delivery - AMD devices

Design Sources

Additional Sources

Prebuilt

Download

Reference Design is only usable with the specified Vivado/Vitis/PetaLinux version. Do never use different Versions of AMD Software for the same Project.

Reference Design is available on:

• TE0710 "Test Board" Reference Design

Design Flow

Trenz Electronic provides a tcl based built environment based on AMD Design Flow.

See also:

• Xilinx Development Tools#XilinxSoftware-BasicUserGuides
• Vivado Projects - TE Reference Design
• Project Delivery.

The Trenz Electronic FPGA Reference Designs are TCL-script based project. Command files for execution will be generated with "_create_win_setup.cmd" on Windows OS and "_create_linux_setup.sh" on Linux OS.

TE Scripts are only needed to generate the vivado project, all other additional steps are optional and can also executed by AMD Vivado/Vitis GUI. For currently Scripts limitations on Win and Linux OS see: Project Delivery Currently limitations of functionality

1. Run _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell:

   Code Block
   language bash theme Midnight title _create_win_setup.cmd/_create_linux_setup.sh
   ------------------------Set design paths---------------------------- -- Run Design with: _create_win_setup -- Use Design Path: <absolute project path> -------------------------------------------------------------------- -------------------------TE Reference Design--------------------------- -------------------------------------------------------------------- -- (0) Module selection guide, project creation...prebuilt export... -- (1) Create minimum setup of CMD-Files and exit Batch -- (2) Create maximum setup of CMD-Files and exit Batch -- (3) (internal only) Dev -- (4) (internal only) Prod -- (c) Go to CMD-File Generation (Manual setup) -- (d) Go to Documentation (Web Documentation) -- (g) Install Board Files from Xilinx Board Store (beta) -- (a) Start design with unsupported Vivado Version (beta) -- (x) Exit Batch (nothing is done!) ---- Select (ex.:'0' for module selection guide):

   
   

2. Press 0 and enter to start "Module Selection Guide"
3. Createproject and follow instructions of the product selection guide, settings file will be configured automatically during this process.
   

   • optional for manual changes: Select correct device and AMD install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"

     Note
     Note: Select correct one, see also Vivado Board Part Flow

     
     

4. Create hardware description file (.xsa file) for PetaLinux project and export to prebuilt folder

   Code Block
   language py theme Midnight title run on Vivado TCL (Script generates design and export files into "<project folder>\prebuilt\hardware\<short name>")
   TE::hw_build_design -export_prebuilt

   
   

   Info
   Using Vivado GUI is the same, except file export to prebuilt folder.

   
   

5. Create and configure your PetaLinux project with exported .xsa-file, see PetaLinux KICKstart
   • use TE Template from "<project folder>\os\petalinux"

   • use exported .xsa file from "<project folder>\prebuilt\hardware\<short name>" . Note: HW Export from Vivado GUI creates another path as default workspace.

   • Important Note: Select correct Flash partition offset on petalinux-config: Subsystem Auto HW Settings → Flash Settings,  FPGA+Boot+bootenv=0xA00000 (increase automatically generate Boot partition), increase image size to A:, see Config

   • The build images are located in the "<plnx-proj-root>/images/linux" directory

6. Configure the boot.scr file as needed, see Distro Boot with Boot.scr
   

7. Copy PetaLinux build image files to prebuilt folder

   • copy u-boot.elf and image.ub from "<plnx-proj-root>/images/linux" to prebuilt folder
     

     Info
     "<project folder>\prebuilt\os\petalinux\<ddr size>" or "<project folder>\prebuilt\os\petalinux\<short name>"

     
     

     Page properties
     hidden true id Comments
     This step depends on AMD Device/Hardware for Zynq-7000 series copy u-boot.elf, u-boot.dtb, system.dtb, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder for ZynqMP copy u-boot.elf, u-boot.dtb, system.dtb, bl31.elf, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder for Microblaze ...

     
     

8. Generate Programming Files with Vitis

   Code Block
   language py theme Midnight title run on Vivado TCL (Script generates applications and bootable files, which are defined in "test_board\sw_lib\apps_list.csv")
   TE::sw_run_vitis -all TE::sw_run_vitis (optional; Start Vitis from Vivado GUI or start with TE Scripts on Vivado TCL)

   
   

   Note
   TCL scripts generate also platform project, this must be done manually in case GUI is used. See Vitis

   
   

9. (Optional) BlockRam Firmware Update

   1. Copy "<project folder>\prebuilt\software\<short name>\spi_bootloader.elf" into  "<project folder>\firmware\microblaze_0\"

   2. Regenerate Vivado Project or Update Bitfile only with "spi_bootloader.elf"

      Code Block
      language bash theme Midnight
      TE::hw_build_design -export_prebuilt TE::sw_run_vitis -all

      
      

Launch

Programming

AMD documentation for programming and debugging: Vivado/Vitis/SDSoC-Xilinx Software Programming and Debugging

Get prebuilt boot binaries

1. Run _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell
2. Press 0 and enter to start "Module Selection Guide"
   1. Select assembly version
   2. Validate selection

   3. Select create and open delivery binary folder

      Info
      Note: Folder "<project folder>\_binaries_<Article Name>" with subfolder "boot_<app name>" for different applications will be generated

      
      

QSPI-Boot mode

Option for u-boot.mcs on QSPI Flash.
(u-boot.mcs contains all files necessary to boot up linux)

1. Connect the USB cable(JTAG) and power supply on carrier with module

2. Open Vivado Project with "vivado_open_existing_project_guimode.cmd" or if not created, create with "vivado_create_project_guimode.cmd"

   Code Block
   language py theme Midnight title run on Vivado TCL (Script programs BOOT.bin on QSPI flash)
   TE::pr_program_flash -swapp u-boot

   
   

3. Reboot (if not done automatically)

SD-Boot mode

Not used on this Example.

JTAG

Not used on this example.

Usage

1. Prepare HW like described on section Programming
2. Connect UART USB (most cases same as JTAG)

3. Select SD Card as Boot Mode (or QSPI - depending on step 1)

   Info
   Note: See TRM of the Carrier, which is used.

   
   

   Tip

   Starting with Petalinux version 2020.1, the industry standard "Distro-Boot" boot flow for U-Boot was introduced, which significantly expands the possibilities of the boot process and has the primary goal of making booting much more standardised and predictable. The boot options described above describe the common boot processes for this hardware; other boot options are possible. For more information see Distro Boot with Boot.scr

   
   

4. Power On PCB

   Expand
   title boot process
   1. FPGA Loads Bitfile from Flash, 2. SPI Bootloader from Bitfile Firmware loads U-Boot into DDR (This takes a while) Image Added 3. U-boot loads Linux from QSPI Flash into DDR

   
   

   Page properties
   hidden true id Comments
   This step depends on AMD Device/Hardware for Zynq-7000 series 1. Zynq Boot ROM loads FSBL from SD/QSPI into OCM, 2. FSBL init the PS, programs the PL using the bitstream and loads U-boot from SD/QSPI into DDR, 3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR for ZynqMP??? 1. ZynqMP Boot ROM loads FSBL from SD/QSPI into OCM, 2. FSBL init the PS, programs the PL using the bitstream and loads PMU, ATF and U-boot from SD/QSPI into DDR, 3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR for Microblaze with Linux 1. FPGA Loads Bitfile from Flash, 2. MCS Firmware configure SI5338 and starts Microblaze, (only if mcs is available) 3. SREC Bootloader from Bitfile Firmware loads U-Boot into DDR (This takes a while), 4. U-boot loads Linux from QSPI Flash into DDR for native FPGA ...

   
   

Linux

1. Open Serial Console (e.g. putty)
   
   • Speed: 9600

   • select COM Port

     Info
     Win OS, see device manager, Linux OS see dmesg |grep tty (UART is *USB1)

     
     

2. Linux Console:
   

   Code Block
   language bash theme Midnight
   root@petalinux:

   
   

   Info
   Note: Wait until Linux boot finished, autologin is activated.

   
   

3. You can use Linux shell now.
   

   Code Block
   language bash theme Midnight
   udhcpc (ETH0 check)

   
   

Vivado HW Manager

Open Vivado HW-Manager and add VIO signal to dashboard (*.ltx located on prebuilt folder)

• Control:
  • User LED Control
  • ETH Power Down
• Monitoring:
  • ETH  Link Status
  • MicroBlaze Reset Status

Scroll Title
anchor Figure_VHM title-alignment center title Vivado_Hardware_Manager
Image Added

Block Design

Constraints

Basic module constraints

set_property BITSTREAM.GENERAL.COMPRESS TRUE [current_design]
set_property BITSTREAM.CONFIG.CONFIGRATE 66 [current_design]
set_property CONFIG_VOLTAGE 3.3 [current_design]
set_property CFGBVS VCCO [current_design]
set_property BITSTREAM.CONFIG.SPI_32BIT_ADDR YES [current_design]
set_property BITSTREAM.CONFIG.SPI_BUSWIDTH 4 [current_design]
set_property BITSTREAM.CONFIG.M1PIN PULLNONE [current_design]
set_property BITSTREAM.CONFIG.M2PIN PULLNONE [current_design]
set_property BITSTREAM.CONFIG.M0PIN PULLNONE [current_design]

set_property BITSTREAM.CONFIG.USR_ACCESS TIMESTAMP [current_design]

set_property BITSTREAM.CONFIG.UNUSEDPIN PULLDOWN [current_design]

Design specific constraints

## set_property PACKAGE_PIN G3 [get_ports {LED_RED_XA_SC[0]}]
## set_property IOSTANDARD LVCMOS15 [get_ports {LED_RED_XA_SC[0]}]

set_property PACKAGE_PIN T10 [get_ports {ETH2_LINK_LED[0]}]
set_property IOSTANDARD LVCMOS33 [get_ports {ETH2_LINK_LED[0]}]
set_property PACKAGE_PIN V15 [get_ports {ETH1_LINK_LED[0]}]
set_property IOSTANDARD LVCMOS33 [get_ports {ETH1_LINK_LED[0]}]
set_property PACKAGE_PIN T18 [get_ports {ETH1_PD_N[0]}]
set_property PACKAGE_PIN D10 [get_ports {ETH2_PD_N[0]}]
set_property IOSTANDARD LVCMOS33 [get_ports {ETH2_PD_N[0]}]
set_property IOSTANDARD LVCMOS33 [get_ports {ETH1_PD_N[0]}]

set_property PACKAGE_PIN L15 [get_ports {LED_RED_D3[0]}]
set_property IOSTANDARD LVCMOS33 [get_ports {LED_RED_D3[0]}]

#EEPROM onewire (MAC ADDRESS)
set_property IOSTANDARD LVCMOS33 [get_ports EEPROM_tri_io]
set_property PACKAGE_PIN D9 [get_ports EEPROM_tri_io]

## IIC Interface
set_property PACKAGE_PIN G3 [get_ports IIC_0_sda_io]
set_property PACKAGE_PIN J5 [get_ports IIC_0_scl_io]
set_property IOSTANDARD LVCMOS15 [get_ports IIC_0_scl_io]
set_property IOSTANDARD LVCMOS15 [get_ports IIC_0_sda_io]

Software Design - Vitis

For Vitis project creation, follow instructions from:

Vitis

Application

Template location: "<project folder>\sw_lib\sw_apps\"

spi_bootloader

TE modified SPI Bootloader from Henrik Brix Andersen.

Bootloader to load app or second bootloader from flash into DDR.

Here it loads the u-

boot.elf from QSPI-Flash to RAM.

Descriptions:

• Modified Files: bootloader.c
• Changes:
  
  • Change the SPI defines in the header
  • Add some reiteration in the frist spi read call

hello_te0710

Hello TE0710 is a Hello World example as endless loop instead of one console output.

u-boot

U-Boot.elf is generated with PetaLinux. Vivado is used to generate *.mcs

Software Design -  PetaLinux

For PetaLinux installation and project creation, follow instructions from:

• PetaLinux KICKstart

Config

Start with petalinux-config or petalinux-config --get-hw-description

Changes:

• SUBSYSTEM_FLASH_AXI_QUAD_SPI_0_BANKLESS_PART0_SIZE = 0x5E0000  (fpga)

• SUBSYSTEM_FLASH_AXI_QUAD_SPI_0_BANKLESS_PART1_SIZE = 0x400000  (boot)

• SUBSYSTEM_FLASH_AXI_QUAD_SPI_0_BANKLESS_PART2_SIZE = 0x20000    (bootenv)

• SUBSYSTEM_FLASH_AXI_QUAD_SPI_0_BANKLESS_PART3_SIZE = 0xD00000  (kernel)

  • (Set kernel flash Address to 0xA00000 (fpga+boot+bootenv) and Kernel size to 0xD00000)

U-Boot

Start with petalinux-config -c u-boot

Changes:

• CONFIG_ENV_IS_NOWHERE=y
• # CONFIG_ENV_IS_IN_SPI_FLASH is not set
• # CONFIG_PHY_ATHEROS is not set
• # CONFIG_PHY_BROADCOM is not set
• # CONFIG_PHY_DAVICOM is not set
• # CONFIG_PHY_LXT is not set
• # CONFIG_PHY_MICREL_KSZ90X1 is not set
• # CONFIG_PHY_MICREL is not set
• # CONFIG_PHY_NATSEMI is not set
• # CONFIG_PHY_REALTEK is not set
• CONFIG_RGMII=y

Busybox

Start with petalinux-config -c busybox

• Miscellaneous Utilities → activate i2cget, i2cset, i2cdetect

Content of platform-top.h located in <plnx-proj-root>\project-spec\meta-user\recipes-bsp\u-boot\files:

#include <configs/microblaze-generic.h>
#include <configs/platform-auto.h>

#define CONFIG_SYS_BOOTM_LEN 0xF000000

Device Tree

Content of system-user.dtsi located in <petalinux project directory>\project-spec\meta-user\recipes-bsp\device-tree\files:

/include/ "system-conf.dtsi"
/ {
};
 
/* QSPI PHY */
 
&axi_quad_spi_0 {
    #address-cells = <1>;
    #size-cells = <0>;
    flash0: flash@0 {
        compatible = "jedec,spi-nor";
        spi-tx-bus-width=<1>;
        spi-rx-bus-width=<4>;
        reg = <0x0>;
        #address-cells = <1>;
        #size-cells = <1>;
        spi-max-frequency = <25000000>;
    };
};
 
 
/* ETH PHY */
&axi_ethernetlite_0 {
    phy-handle = <&phy0>;
    mdio {
        #address-cells = <1>;
        #size-cells = <0>;
        phy0: phy@0 {
            device_type = "ethernet-phy";
            reg

Kernel

Start with petalinux-config -c kernel

Changes:

• No changes.

Rootfs

Start with petalinux-config -c rootfs

Changes:

• # CONFIG_dropbear is not set
• # CONFIG_dropbear-dev is not set
• # CONFIG_dropbear-dbg is not set
• # CONFIG_packagegroup-core-ssh-dropbear is not set
• # CONFIG_packagegroup-core-ssh-dropbear-dev is not set
• # CONFIG_packagegroup-core-ssh-dropbear-dbg is not set
• # CONFIG_imagefeature-ssh-server-dropbear is not set

• CONFIG_imagefeature-serial-autologin-root = y

Applications

See "<project folder>\os\petalinux\project-spec\meta-user\recipes-apps\"

eeprom

eeprom is a simple bash script implemented in petalinux as an application that executes on startup. It reads the unique 48-bit MAC from the onboard eeprom and uses it to set the system MAC address.

Additional Software

No additional software is needed.

App. A: Change History and Legal

Notices

Document Change History

To get content of older

revision go to "Change History"

of this page and select older document revision number.

Legal Notices