Page History

...

• Single 24V main power supply
• 2x USB3 A Connector (Superspeed Host Port (Highspeed in USB2 mode))
• Gigabit Ethernet RGMII PHY with RJ45 MegJack
• Dual SFP+ Connector (2x1 Cage)
• DDR4-SDRAM SO-DIMM socket (64bit bus width)
• SSD (Solid State Disk) PCIe connector
• CAN FD interface (D-SUB 9-pin male connector and 6-pin header)
• DisplayPort (2 lanes)
• 4x On-board configuration EEPROMs (1x Microchip 24LC128-I/ST, 3x  Microchip 24AA025E48T-I/OT)
• All carrier board peripherals' I²C interfaces muxed to MPSoC's I²C interface
• 6x FMC connectors
• 6x FMC Fans
• 3x  4-wire PWM fan connectors
• 10 output programmable PLL clock generator Si5345A
• Quad programmable PLL clock generator SI5338A
• 1x SMA coaxial connectors connector for reference clock signal input
• SD Card socket (bootable)
• 32 Gbit (4 GByte) on-board eMMC flash (8 banks a 4 Gbit)
• System Controller CPLD Lattice MachXO2 7000 HC
• 2x XMOD header for programming MPSoC and SC CPLD
• On-board DC-DC PowerSoCs and LDOs

...

1. SFP+ 2x1 cage with integrated LED light pipes, J9
2. DisplayPort connector, J12
3. USB3 A 2x , RJ45 1x (stacked), J13
4. FMC connector (FMC B), J4
5. FMC B cooling fan, M2
6. FMC connector (FMC C), J8
7. FMC C cooling fan, M3
8. FMC connector (FMC D), J7
9. FMC D cooling fan, M4
10. FMC connector (FMC E), J6
11. FMC E cooling fan, M5
12. I²C programming header of on-board PLL clock generator U17, J22
13. 4-Wire PWM fan connector, J23
14. Main Power Jack 24V, J1
15. CAN bus D-SUB 9-pin male connector, J3
16. CAN bus 6-pin header male, J15
17. XMOD JTAG header for access to System Controller CPLD, J35
    
18. XMOD JTAG header for access to Zynq MPSoC, J24
19. 4-Wire PWM fan connector, J33
20. Battery Holder CR1220, B1
21. SMT SMA coaxial connector (PLL Si5345A U17 clock input), J25
22. Push Button, S1
23. Push Button, S2
24. DDR4 SO-DIMM socket, U3
25. 4-bit DIP-switch, S4
26. 4-bit DIP-switch, S3
27. FMC connector (FMC A), J10
28. FMC A cooling fan, M1
29. FMC connector (FMC F), J21
30. FMC F cooling fan, M6
31. NGFF M.2 PCIe socket (Key M), U2
32. SD Card socket, J11
33. User LEDs (3x green, 1x red) with LED light pipe, D13 ... D16
    
34. Green LEDs dedicated to USB3 hub U4, D17 ... D19
35. Red LED indicating FPGAs 'DONE' signal, D6
36. 4-Wire PWM fan connector, J2
37. Xilinx Zynq Ultrascale+ MPSoC, U1
    

...

1. FMC A
2. FMC B
3. FMC C
4. FMC D
5. FMC E
6. FMC F
   

FMC A

FMC A Interfaces:

...