Versions Compared

Old Version 33

changes.mady.by.user Pedram Babakhani

Saved on

compared with

New Version 34

changes.mady.by.user Pedram Babakhani

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Page properties
hiddentrue
idComments

Note:
Use 'Key Features' description in shoping page, for example: https://shop.trenz-electronic.de/de/TE0728-04-1Q-SoC-Micromodul-mit-Xilinx-Automotive-Zynq-7020-512-MByte-DDR3L-6-x-6-cm

  • Single 3.3V input (Direct modules power supply)
  • Pin Header for TE0790 JTAG/UART Adapter
  • ARM JTAG header (connected to MIO JTAG 0)
  • 10 Pin Header for I2CI2C header for Silabs Clock Builder Field Programmer
  • Done/Error/Status LEDs
  • Board to Board (B2B) Connectors
  • One PL GT with 4x SMA Connectors
  • One PS GT with 4x SMA Connectors
  • GT local loopback
  • PL I/O loopbacks
  • PS I/O loopbacks
  • MEMS Oscillator 125.0 MHz
  • Boot Mode DIP-Switch
  • Power control switches 2x DIP-Switches to control TE080x power domains
  • One pre-assembled TE0790 XMOD FTDI JTAG adapter
  • Power Supply:
    • Single 3.3V (Direct modules power supply)
  • Dimension: 90mm x 90mm
  • Others:
    • One pre-assembled TE0790 XMOD FTDI JTAG adapter

Block Diagram

Page properties
hiddentrue
idComments

add drawIO object here.

Note

For more information regarding how to draw a diagram, Please refer to "Diagram Drawing Guidline" .


...

Scroll Title
anchorFigure_OV_BD
titleTEBT0808 Block Diagram


Scroll Ignore
draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision1617
diagramNameTEBT0808_OV_BD
simpleViewerfalse
width
linksauto
tbstylehidden
diagramWidth640



Scroll Only


...

Scroll Title
anchorTable_SIP_JTG
titleJTAG Pins Connection

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

JTAG Signal

B2B Connector

Notes
TMSJ2- 126
TDIJ2- 122
TDOJ2- 124
TCKJ2- 120


There is a DIP switch, S2, on TE0790 adapter which must be set accordingly.

...

The voltages 3.3V (VCC) and VIO (variable SC CPLD I/O-voltage) can be configured by the DIP-switch S2-switches 3 and S2-4 on TE0790:

Scroll Title
anchorTable_SIP_Xmod_DIP
title Xmod Adapter DIP-Switch Setting Description

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DIP Switch-3DIP Switch-43.3V (VCC) Pin 5VIO Pin 6Description
OFFOFF3.3V from base VIO from base3.3V (pin 5) and VIO (pin 6) sourced from base
OFFON3.3V from USBVIO from baseVIO sourced from base by Pin 6
ONOFF3.3V from base3.3V from baseVIO and 3.3V source by base (Pin 5 and Pin 6 are shorted and both must be sourced by 3.3V)
ONON3.3V from USB3.3V from USB

3.3V (pin 5) and VIO (pin 6) sourced USB (Pin 5 and Pin 6 are shorted and both are 3.3V)


...

Scroll Title
anchorTable_TS_ROC
titleRecommended operating conditions.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

SymbolsMinMaxUnitNote
VIN3,143.47VImportant, check also TRM of the connected module
Operating Temperatur-40+85°C


Physical Dimensions

  • Module size: 90 mm × 90 mm.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 3.5 mm.

...

Scroll Title
anchorTable_RH_HRH
titleHardware Revision History

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DateRevisionChangesDocumentation Link
2016-05-3001Initial ReleaseREV01


Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Scroll Title
anchorFigure_RV_HRN
titleBoard hardware revision number.


Scroll Ignore
draw.io Diagram
bordertrue
viewerToolbartrue
fitWindowfalse
diagramNameTEBT0808_RV_HRN
simpleViewerfalse
width
diagramWidth158
revision1



Scroll Only
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue

Image Added


Document Change History

Page properties
hiddentrue
idComments
  • Note this list must be only updated, if the document is online on public doc!
  • It's semi automatically, so do following

    • Add new row below first

    • Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> this point is will be deleted on newer pdf export template

    • Metadata is only used of compatibility of older exports

...