Page History
...
...
...
...
Table of Contents |
---|
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
Initial Delivery State
...
...
...
...
...
...
...
...
---
...
...
...
...
...
...
RESETN
...
Signals, Interfaces and Pins
Page properties | ||||
---|---|---|---|---|
| ||||
Notes :
|
Board to Board (B2B) I/Os
FPGA bank number and number of I/O signals connected to the B2B connector:
...
...
...
...
Gigabit Ethernet
...
...
...
...
...
Micro USB for JTAG/UART
The TEB0835 is equipped with two Micro USB2.0 Connectors J29, J30.
...
anchor | Table_SIP_MUSB2 |
---|---|
title | Micro USB2 to JTAG/UART connections |
...
Micro USB2.0
There is a Micro USB2.0 port provided for user.
...
anchor | Table_SIP_MicroUSB2 |
---|---|
title | Micro USB2.0 Socket connections |
...
SMA Connectors
There are 6 SMA Connectors provided for Analog and Digital signals.
...
anchor | Table_SIP_SMA |
---|---|
title | SMA Connectors information |
...
...
...
...
...
...
...
UMCC Connectors
...
...
...
...
...
UCE5 Connectors
The TEB0835 is equipped with two UCE5 Connectors.
...
anchor | Table_SIP_UEC5 |
---|---|
title | UEC5 Connectors |
...
...
...
...
...
...
...
UCC8 Connectors
The TEB0835 is equipped with two UCC8 Connectors.
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
PCIe Card
...
...
...
...
...
Test Points
...
hidden | true |
---|---|
id | Comments |
you must fill the table below with group of Test Point which are indicated as TP in a schematic. If there is no Test Point remarked in the schematic, delet the Test Point section.
Example:
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
On-board Peripherals
Page properties | ||||
---|---|---|---|---|
| ||||
Notes :
|
Page properties | ||||
---|---|---|---|---|
| ||||
Notes : In the on-board peripheral table "chip/Interface" must be linked to the corresponding chapter or subsection |
...
anchor | Table_OBP |
---|---|
title | On board peripherals |
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
FTDI
The FTDI chip U12 converts signals from USB2 to a variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip. FTDI FT2232H chip is used in MPPSE mode for JTAG, 2 I/O's of Channel B are routed to B2B J17 and must be used as UART.
The configuration of FTDI FT2232H chip is pre-programmed on the EEPROM U9.
...
anchor | Table_OBP_FTDI |
---|---|
title | FTDI chip interfaces and pins |
Scroll Table Layout | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
|
...
B2B, J17
...
...
...
...
...
...
...
...
Clock Sources
...
...
...
...
...
...
...
Programmable Clock Generator
There is a programmable clock generator on-board (U5) provided in order to generate variable clocks for the module. Programming can be done using I2C via PIN header J20. The I2C Address is 0x70.
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
Power and Power-On Sequence
...
hidden | true |
---|---|
id | Comments |
In 'Power and Power-on Sequence' section there are three important digrams which must be drawn:
- Power on-sequence
- Power distribution
- Voltage monitoring circuit
Note |
---|
For more information regarding how to draw diagram, Please refer to "Diagram Drawing Guidline" . |
Power Supply
Power supply with minimum current capability of 3 A for system startup is recommended.
Power Consumption
...
...
* TBD - To Be Determined
Power Distribution Dependencies
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
Scroll Only |
---|
image link to the generate DrawIO PNG file of this page. This is a workaround until scroll pdf export bug is fixed |
Power Rails
...
Scroll Only |
---|
Power-On Sequence
...
anchor | Figure_PWR_PS |
---|---|
title | Power Sequency |
...
...
...
...
B2B JM17
...
B2B JM2
...
Board to Board Connectors
...
hidden | true |
---|---|
id | Comments |
...
use "include page" macro and link to the general B2B connector page of the module series,
...
Technical Specifications
Absolute Maximum Ratings
...
anchor | Table_TS_AMR |
---|---|
title | PS absolute maximum ratings |
...
Recommended Operating Conditions
...
...
...
...
...
...
...
...
Physical Dimensions
Module size: 106.6 mm × 167.7 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 5 mm.
PCB thickness: 1.5 mm.
...
hidden | true |
---|---|
id | Comments |
In 'Physical Dimension' section, top and bottom view of module must be inserted, information regarding physical dimensions can be obtained through webpage for product in Shop.Trenz, (Download> Documents> Assembly part) for every SoM.
For Example: for Module TE0728, Physical Dimension information can be captured by snipping tools from the link below:
Note |
---|
For more information regarding how to draw diagram, Please refer to "Diagram Drawing Guidline" . |
...
anchor | Figure_TS_PD |
---|---|
title | Physical Dimension |
...
Scroll Only | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||
Currently Offered Variants
...
hidden | true |
---|---|
id | Comments |
Set correct link to the shop page overview table of the product on English and German.
Example for TE0728:
...
...
...
...
...
...
...
...
...
...
...
...
...
Revision History
Hardware Revision History
Page properties | ||||
---|---|---|---|---|
| ||||
Set correct links to download arrier, e.g. TE0706 REV02: TE0706-02 -> https://shop.trenz-electronic.de/Download/?path=Trenz_Electronic/Modules_and_Module_Carriers/4x5/4x5_Carriers/TE0706/REV02/Documents Note:
|
...
anchor | Table_RH_HRH |
---|---|
title | Hardware Revision History |
...
...
...