Page History
...
...
...
Table of Contents
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
Initial Delivery State
...
...
...
...
...
MODE Signal State
...
...
---
...
...
...
...
...
RESETN
...
...
Signals, Interfaces and Pins
Page properties | ||||
---|---|---|---|---|
| ||||
Notes :
|
Board to Board (B2B) I/Os
Number of I/O signals and interfaces connected to the B2B connectors:
...
...
...
...
...
PLL Intrupt
PLL Clocks
...
1x Single Ended
4x Single Ended, 2x Differential pairs
...
CPLD IO
CPLD Enable
...
3x Single Ended
1x Single Ended
...
Ethernet LED
Ethernet MDI
...
2x Single Ended
8x Single Ended
...
Micro SD Memory Connector, J28
IO Expander, U11
...
2x Single Ended
1x Single Ended
2x Single Ended
...
Micro USB2.0 Connector, J30
Voltage Regulator, U17
Diode, D5
...
SMA, J1, J3, J5, J7
UMCC, J2, J4, J6, J8
...
...
16x Single Ended, 8x Differential pairs
...
SMA, J9, J11
UMCC, J10, J12, J13...16
...
10x Single Ended
...
Gigabit Ethernet
...
anchor | Table_SIP_ETH |
---|---|
title | Ethernet PHY to Zynq SoC connections |
...
Micro USB for JTAG/UART
The TEB0835 is equipped with two Micro USB2.0 Connectors J29, J30.
...
anchor | Table_SIP_MUSB2 |
---|---|
title | Micro USB2 to JTAG/UART connections |
...
Micro USB2.0
...
...
...
...
...
...
...
SMA Connectors
...
...
...
...
...
UMCC Connectors
There are 8 UMCC Connectors provided for Analog and Digital signals input and output.
...
anchor | Table_SIP_UMCC |
---|---|
title | UMCC Connectors |
...
...
...
...
...
...
...
...
...
...
...
...
...
UCE5 Connectors
The TEB0835 is equipped with two UCE5 Connectors.
...
anchor | Table_SIP_UEC5 |
---|---|
title | UEC5 Connectors |
...
...
...
...
...
...
...
...
...
...
UCC8 Connectors
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
PCIe Card
...
...
...
...
...
Test Points
...
hidden | true |
---|---|
id | Comments |
you must fill the table below with group of Test Point which are indicated as TP in a schematic. If there is no Test Point remarked in the schematic, delet the Test Point section.
Example:
...
anchor | Table_SIP_TPs |
---|---|
title | Test Points Information |
...
On-board Peripherals
Page properties | ||||
---|---|---|---|---|
| ||||
Notes :
|
...
hidden | true |
---|---|
id | Comments |
Notes :
...
...
...
...
...
...
...
...
...
anchor | Table_OBP_EEP |
---|---|
title | I2C EEPROM interface MIOs and pins |
...
...
...
...
FTDI
The FTDI chip U12 converts signals from USB2 to a variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip. FTDI FT2232H chip is used in MPPSE mode for JTAG, 2 I/O's of Channel B are routed to B2B J17 and must be used as UART.
The configuration of FTDI FT2232H chip is pre-programmed on the EEPROM U9.
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
B2B, J17
...
...
...
...
...
...
...
...
...
Clock Sources
...
anchor | Table_OBP_CLK |
---|---|
title | Osillators |
...
...
...
...
...
Programmable Clock Generator
...
...
...
...
...
...
...
...
...
...
...
...
...
...
Power Supply
Power supply with minimum current capability of 3 A for system startup is recommended.
Power Consumption
...
anchor | Table_PWR_PC |
---|---|
title | Power Consumption |
...
* TBD - To Be Determined
Power Distribution Dependencies
...
anchor | Figure_PWR_PD |
---|---|
title | Power Distribution |
...
Scroll Only |
---|
Power-On Sequence
...
anchor | Figure_PWR_PS |
---|---|
title | Power Sequency |
...
Scroll Only |
---|
Power Rails
...
anchor | Table_PWR_PR |
---|---|
title | Module power rails. |
...
B2B JM17
...
B2B JM2
...
Board to Board Connectors
...
Power and Power-On Sequence
...
hidden | true |
---|---|
id | Comments |
In 'Power and Power-on Sequence' section there are three important digrams which must be drawn:
- Power on-sequence
- Power distribution
- Voltage monitoring circuit
Note |
---|
For more information regarding how to draw diagram, Please refer to "Diagram Drawing Guidline" . |
...
use "include page" macro and link to the general B2B connector page of the module series,
...
Technical Specifications
...
...
...
...
...
...
...
...
...
...
Recommended Operating Conditions
...
...
...
...
...
...
...
...
...
...
...
...
...
Physical Dimensions
Module size: 106.6 mm × 167.7 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 5 mm.
PCB thickness: 1.5 mm.
...
hidden | true |
---|---|
id | Comments |
In 'Physical Dimension' section, top and bottom view of module must be inserted, information regarding physical dimensions can be obtained through webpage for product in Shop.Trenz, (Download> Documents> Assembly part) for every SoM.
For Example: for Module TE0728, Physical Dimension information can be captured by snipping tools from the link below:
Note |
---|
For more information regarding how to draw diagram, Please refer to "Diagram Drawing Guidline" . |
...
anchor | Figure_TS_PD |
---|---|
title | Physical Dimension |
...
Scroll Only | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||
Currently Offered Variants
...
hidden | true |
---|---|
id | Comments |
Set correct link to the shop page overview table of the product on English and German.
Example for TE0728:
ENG Page: https://shop.trenz-electronic.de/en/Products/Trenz-Electronic/TE07XX-Zynq-SoC/TE0728-Zynq-SoC/
...
...
...
...
...
...
...
...
...
...
...
Revision History
Hardware Revision History
Page properties | ||||
---|---|---|---|---|
| ||||
Set correct links to download arrier, e.g. TE0706 REV02: TE0706-02 -> https://shop.trenz-electronic.de/Download/?path=Trenz_Electronic/Modules_and_Module_Carriers/4x5/4x5_Carriers/TE0706/REV02/Documents Note:
|
...
anchor | Table_RH_HRH |
---|---|
title | Hardware Revision History |
...
...
...