Download PDF version of this document.
Table of Contents
The carrier board TEB0745 was especially designed and developed for the use of Trenz Electronic module TE0745.
Refer to http://trenz.org/teb0745-info for the current online version of this manual and other available documentation.
Storage device name | Content | Notes |
|---|---|---|
| EEPROM | EUI-64 number programmed | Can be used for MAC |
MODE Signal State | Connected to | B2B | Status | Boot Mode |
|---|---|---|---|---|
BOOTMODE | S1 | J2-133 | Open | QSPI |
| Short | SD Card |
Schematic | Connected to | B2B | Note |
|---|---|---|---|
| RST_IN_N | Push Button, S2 | J2-131 | Low Active Reset |
FPGA bank number and number of I/O signals connected to the B2B connector:
| B2B Connector | Interfaces | Number of I/O | Notes |
|---|---|---|---|
| J1 | User I/O | 48 singel ended, 24 Differential 2 singel ended | Connected to Bank 13 |
48 singel ended, 24 Differential 2 singel ended | Connected to Bank 12 | ||
| JTAG Interface | 5 single ended | TCK, TDI, TMS, TDO, JTAG_EN | |
| SFP+ Connector | 8 Diff | SPF4....7_RX_N/P , SPF4....7_TX_N/P | |
| J2 | Ethernet PHY | 4 Differential | |
| 2 single ended | PHY_LED0...1 | ||
| USB | 1 Differential | OTG_N/P | |
| Control Signals | 3 single ended | PS_SRST, BOOTMODE, RST_IN_N | |
| Power Control Signal | 2 single ended | PWR_PS_OK, PWR_PL_OK | |
| I2C Bus | 2 single ended | I2C_SDA, I2C_SCL | |
| User I/O | 4 single ended | MIO12...15 | |
J3 | User I/O | 6 Single ended | MIO46...51 |
| SD Card Connector | 6 Single ended | SD_CLK, SD_CMD, SD_DAT0...3 (MIO40...45) | |
| SFP+ Connector | 8 Differential | SPF0....3_RX_N/P , SPF0....3_TX_N/P |
JTAG access to the TEB0745 SoM is available through B2B connector JB1 and JB2. JTAG_EN is connected to J1-138, JTAG_EN can be activated through DIP Switch S1-2.
| Designator | Connected to | B2B Pin | XMOD Header JB1 | Note |
|---|---|---|---|---|
| A | MIO15 | J2-129 | JB1-3 | UART TX - Input to the module |
| B | MIO14 | J2-127 | JB1-7 | UART RX - Output of the module |
| C | TCK | J1-143 | JB1-4 | JTAG interface signal |
| D | TDO | J1-145 | JB1-8 | JTAG interface signal |
| F | TDI | J1-142 | JB1-10 | JTAG interface signal |
| H | TMS | J1-144 | JB1-12 | JTAG interface signal |
| G | RST_IN_N | J2-131 | JB1-11 | RESET will be connected to Push Button on JTAG Programmer |
There is a DIP switch, S2, on TE0790 adapter which must be set as following.
| DIP Switch,S2 | Default | Description |
|---|---|---|
| 1 | ON | Update Mode JTAG access to SC CPLD only |
| 2 | OFF | Must be always in OFF state. |
| 3 | OFF | VIO is supplied from Module |
| 4 | ON | 3.3V from XMOD |
The TEB0745 is equipped with 8 SFP+ Connectors,
| Pin | Connected to | Notes | |||||||
|---|---|---|---|---|---|---|---|---|---|
| SFP+ , J4 | SFP+, J6 | SFP+, J8 | SFP+, J10 | SFP+, J13 | SFP+, J15 | SFP+, J18 | SFP+, J20 | ||
| TD+ | B2B, J3 | B2B, J3 | B2B, J3 | B2B, J3 | B2B, J1 | B2B, J1 | B2B, J1 | B2B, J1 | GT |
| TD- | B2B, J3 | B2B, J3 | B2B, J3 | B2B, J3 | B2B, J1 | B2B, J1 | B2B, J1 | B2B, J1 | GT |
| RD+ | B2B, J3 | B2B, J3 | B2B, J3 | B2B, J3 | B2B, J1 | B2B, J1 | B2B, J1 | B2B, J1 | GT |
| RD- | B2B, J3 | B2B, J3 | B2B, J3 | B2B, J3 | B2B, J1 | B2B, J1 | B2B, J1 | B2B, J1 | GT |
| TX FAULT | IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | SFP_CTRL |
| TX DISABLE | IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | SFP_CTRL |
| MOD-DEF2 | IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | SFP_CTRL |
| MOD-DEF1 | IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | SFP_CTRL |
| MOD-DEF0 | IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | SFP_CTRL |
| RS0 | IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | SFP_CTRL |
| LOS | IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | SFP_CTRL |
| RS1 | IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | SFP_CTRL |
Power supply voltage for SD card holder is 3.3V.
| Signals | Connected to | B2B | Notes |
|---|---|---|---|
| SD_CLK | MIO40 | J3-150 | |
| SD_CMD | MIO41 | J3-152 | |
| SD_DAT0 | MIO42 | J3-154 | |
| SD_DAT1 | MIO43 | J3-156 | |
| SD_DAT2 | MIO44 | J3-158 | |
| SD_DAT3 | MIO45 | J3-160 |
Ethernet Socket is connected to Board to Board (B2B) JM2.
| Signal | B2B | Notes |
|---|---|---|
| PHY_MDIO0_P | J2-120 | |
| PHY_MDIO_N | J2-122 | |
| PHY_MDIO1_P | J2-126 | |
| PHY_MDIO1_N | J2-128 | |
| PHY_MDIO2_P | J2-132 | |
| PHY_MDIO2_N | J2-134 | |
| PHY_MDIO3_P | J2-138 | |
| PHY_MDIO3_N | J2-140 | |
| PHY_LED0 | J2-144 | |
| PHY_LED1 | J2-146 |
Test Point | Signals | B2B Connector | Notes |
|---|---|---|---|
| TP 1 | 5V | - | |
| TP 2 | VBAT_IN | J1-146 | |
| TP 3 | VCCIO18V | J2- J3 | |
| TP 4 | VCC_HR_B | J1 | |
| TP 5-9 | GND | - | |
| TP 10 | PS_1.8V | J2 | |
| TP 11 | VCC_HR_B | J1 | |
| TP 12 | 3.3V | J1- J2 | |
| TP 13 | - | - | |
| TP 14 | - | - | |
| TP 15 | PWR_PL_OK | J2- 135 | |
| TP 16 | PWR_PS_OK | J2-139 | |
| TP 17 | 24V_FUSED | - | |
| TP 18 | 3.3V_SFP | - |
| Chip/Interface | Designator | Notes |
|---|---|---|
| EEPROM | U33 | |
| S1, S4 | ||
| I2C Switch | U16 | |
| I/O Expander | U18...U25 | |
| Push Buttons | S2, S3 | |
| LEDs | D1, D5 |
| MIO Pin | Schematic | B2B | Notes |
|---|---|---|---|
| MIO10 | I2C_SCL | J2-119 | |
| MIO11 | I2C_SDA | J2-121 |
| I2C Device | Designator | I2C Address | Notes |
|---|---|---|---|
| EEPROM | U33 | 0x51 |
There are two DIP Switches S1,S4.
| Designator | Connected to | B2B | Note |
|---|---|---|---|
| S1-A | BootMode | J2-133 | |
| S1-B | JTAG_EN | J1-148 | |
| S1-C | - | ||
| S1-D | PS_SW | J2-123 |
VCC_HR_B voltage can be selected using DIP Switch S4 .
| S4-1 | S4-2 | S4-3 | S4-4 | Power VCC_HR_B | Notes |
|---|---|---|---|---|---|
| OFF | OFF | OFF | N.C. | 1,8V | |
| OFF | OFF | ON | N.C. | 1,5V | |
| OFF | ON | OFF | N.C. | 3,3V | |
| OFF | ON | ON | N.C. | 2,5V | |
| ON | OFF | OFF | N.C. | 0,8V | |
| ON | OFF | ON | N.C. | Do not use | |
| ON | ON | OFF | N.C. | 1,25V | |
| ON | ON | ON | N.C. | 1,2V |
There is a I2C Switch on the TEB0745 which can be used in order to controll the SPF+ Connectors.
| Pin | Schematic | Connected to | Notes |
|---|---|---|---|
| VCC | 3.3V | ||
| SCL | I2C_SCL | B2B, J2 | |
| SDA | I2C_SDA | B2B, J2 | |
| nRESET | I2C_RST | Voltage Translator, U34 | |
| A0 | GND | Low | I2C address is 0x72 |
| A1 | 3.3V | High | I2C address is 0x72 |
| A2 | GND | Low | I2C address is 0x72 |
| SD0/ SC0 | SFP0_SDA / SFP0_SDA | SFP+ Connector, J4 | |
| SD1/ SC1 | SFP1_SDA / SFP1_SDA | SFP+ Connector, J6 | |
| SD2/ SC2 | SFP2_SDA / SFP2_SDA | SFP+ Connector, J8 | |
| SD3/ SC3 | SFP3_SDA / SFP3_SDA | SFP+ Connector, J10 | |
| SD4/ SC4 | SFP4_SDA / SFP4_SDA | SFP+ Connector, J13 | |
| SD5/ SC5 | SFP5_SDA / SFP5_SDA | SFP+ Connector, J15 | |
| SD6/ SC6 | SFP6_SDA / SFP6_SDA | SFP+ Connector, J18 | |
| SD7/ SC7 | SFP7_SDA / SFP7_SDA | SFP+ Connector, J20 |
| I2C Device | Designator | I2C Address | Notes |
|---|---|---|---|
| I2C Device | U16 | 0x72 |
The TEB0745 is equipped with 8 I/O Expanders.
| Pin | Connected to | Notes | |||||||
|---|---|---|---|---|---|---|---|---|---|
| IO Exp, U18 | IO Exp, U19 | IO Exp, U20 | IO Exp, U21 | IO Exp, U22 | IO Exp, U23 | IO Exp, U24 | IO Exp, U25 | ||
| nINT | Not Connected | Not Connected | Not Connected | Not Connected | Not Connected | Not Connected | Not Connected | Not Connected | |
| SCL | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | |
| SDA | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | I2C Switch, U16 B2B, J2 | |
| A0 | GND | 3.3V | GND | 3.3V | GND | 3.3V | GND | 3.3V | |
| A1 | GND | GND | 3.3V | 3.3V | GND | GND | 3.3V | 3.3V | |
| A2 | GND | GND | GND | GND | 3.3V | 3.3V | 3.3V | 3.3V | |
| VCC | 3.3V | 3.3V | 3.3V | 3.3V | 3.3V | 3.3V | 3.3V | 3.3V | |
| P0...P7 | SFP+, J4 | SFP+, J6 | SFP+, J8 | SFP+, J10 | SFP+, J13 | SFP+, J15 | SFP+, J18 | SFP+, J20 | |
In the following table you can find I2C addresses of I/O Expanders which would be designated by pins A0,A1 and A2.
| I2C Device | Designator | I2C Address | Notes |
|---|---|---|---|
| I/O Expander | U18 | 0x20 | |
| U19 | 0x21 | ||
| U20 | 0x22 | ||
| U21 | 0x23 | ||
| U22 | 0x24 | ||
| U23 | 0x25 | ||
| U24 | 0x26 | ||
| U25 | 0x27 |
There are two push buttons S2, S3.
| Designator | Connected to | B2B | Active Level | Note |
|---|---|---|---|---|
| S3 | USR_BTN | J3-153 | Active high | |
| S2 | RST_IN_N | J2-131 | Active high | General Reset |
| Designator | Color | B2B | Connected to | Active Level | Note |
|---|---|---|---|---|---|
| D1 | Green | J3-149 | MIO48 | Active High | LED1 |
| D5 | Green | J3-151 | MIO49 | Active High | LED2 |
Power supply with minimum current capability of 2.5 A for system startup is recommended.
| Power Input Voltage | Typical Current |
|---|---|
| 24V | TBD* |
| VBAT | TBD* |
* TBD - To Be Determined
| Power Rail Name | B2B Connector JM1 Pin | B2B Connector JM2 Pin | B2B Connector JM3 Pin | Direction | Notes |
|---|---|---|---|---|---|
| 3.3V | 147, 149, 151, 153, | 154, 156, 158,160 | - | Output | PL_VIN |
| VCCIO12 | 54, 55 | - | - | Output | high range bank I/O voltage |
| VCCIO13 | 112, 113 | - | - | Output | high range bank I/O voltage |
| VCCIO33 | - | - | 115, 120 | Output | high performance bank I/O voltage |
| VCCIO34 | - | 29, 30 | - | Output | high performance bank I/O voltage |
| VCCIO35 | - | 87, 88 | - | Output | high performance bank I/O voltage |
| VBAT_IN | 146 | - | - | Output | RTC (battery-backed) supply voltage |
| PS_1.8V | - | 130 | - | Input | internal 1.8V voltage level (Process System) |
5.2 x 7.6 cm SoM Zynq carrier use three Samtec Razor Beam LP Socket Strip (SS5) on the top side.
| Symbols | Min | Max | Unit | Note |
|---|---|---|---|---|
| VIN Supply Voltage | 0 | 24 | V | |
| Storage Temperatur | -25 | +85 | °C |
Operating temperature range depends also on customer design and cooling solution.
| Parameter | Min | Max | Units | Reference Document |
|---|---|---|---|---|
| VIN Supply Voltage | 20 | 25.4 | V | See LTC4365ITS8 Datasheet |
| Operating Temperatur | -40 | +85 | °C |
Module size: 200 mm x 231 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 3.5 mm.
| Trenz shop TEB0745 overview page | |
|---|---|
| English page | German page |
| Date | Revision | Changes | Documentation Link |
|---|---|---|---|
| 2018-12-06 | 02a |
| REV02-A |
| 2018-10-19 | 02 |
| REV02 |
| 2016-05-25 | 01 | - | REV01 |
Hardware revision number can be found on the PCB board together with the module model number separated by the dash.
| Date | Revision | Contributor | Description |
|---|---|---|---|
| |||
| 2020-09-01 | v.135 | John Hartfiel |
|
| 2019-12-08 | v.134 | Pedram Babakhani |
|
-- | all |
|
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
Products (incl. Software and Firmware) are exclusively designed, manufactured, and distributed for industrial applications. They are not intended, authorized, or certified for use in critical safety applications, medical devices, aerospace, nuclear, life-support, traffic-control, military, or other environments where malfunction or failure could result in personal injury, death, or significant property or environmental damage.
Trenz Electronic GmbH (“Manufacturer”) excludes any liability for inappropriate use in such contexts. The Customer bears all responsibility for verifying suitability and compliance with applicable regulations when deploying in any critical-use scenario. The Customer also agrees to indemnify and hold harmless the Manufacturer from any third-party claims or liabilities arising from such use.
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.