How to write C# programs using the new DLL starting from the old DLL.

Introduction

There are some major differences between the two DLLs.

feature	Dewesoft C++ DLL	Trenz Electronic C# DLL
programming language	C++	C#
architecture	standard (TE0300DLL.dll)	stacked (TE_USB_FX2_CyUSB.dll requires Cypress CyUSB.dll);
Handles	present	absent
structures	embedded	defined in Cypress CyAPI.h
parameters*	less	more
freedom*	less	more
buffer size	2 Kbyte (fixed)	4 Kbyte or more (it can be changed)

Function translation

Dewesoft C++ DLL	Trenz Electronic C# DLL
HANDLE m_handle = 0;	CyUSBDevice TE_USB_FX2_USBDevice = null; USBDeviceList USBdevList = new USBDeviceList(CyConst.DEVICES_CYUSB); The handles are internally managed by CyAPI.lib and there is no need to expose them to the user. CyUSBDevice TE_USB_FX2_USBDevice take the place of handles for C# programmers.
cout << endl << TE0300_ScanCards() << endl;	int NumberOfCardAttached = TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_ScanCards(ref USBdevList); Console.WriteLine(" {0} ", NumberOfCardAttached);
TE0300_Open(&m_handle, 0)!=0	TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_Open (ref TE_USB_FX2_USBDevice, ref USBdevList, 0) == false TE_USB_FX2_Open() In the code, it is possible to call TE_USB_FX2_Open() where TE0300_Open() is used. TE_USB_FX2_Open() act as Close() for other TE USB handles already open When a new handle to the device driver is open (TE_USB_FX2_Open() run successfully) other internal handles (inside USBDeviceList) are automatically closed by TE_USB_FX2_Open() function. No more than one handle can be active on the same time. It is a behavior inherithed by CyAPI.dll Open() function. For this reason, TE_USB_FX2_Close() function is almost useless. TE_USB_FX2_Open() as SelectCard() TE_USB_FX2_Open(TE_USB_FX2_USBDevice, USBdevList, x) acts more as a SelectCard() function because the list of USB devices is already created in USBdevList. TE_USB_FX2_USBDevice is the selected device number x (0 in this case).
TE0300_Open(&m_handle, 1)!=0	TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_Open (ref TE_USB_FX2_USBDevice, ref USBdevList, 1) == false
TE0300_Close(&m_handle);	TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_Close (ref USBdevListToDispose); In the code, it is not recommended to call TE_USB_FX2_Close() where TE0300_Close() is used. This function differs from its homonym of the previous TE0300DLL.dll in that it does not close a Handle but disposes (erases) all USB devices in the list USBdevList. The reason of this behavior is due to the CyUSB.dll as explained by Cypress document CyUSB.NET.pdf, pages 132-133 and pages 139-140: "You should never invoke the Dispose() method of a USBDevice directly. Rather, the appropriate technique is to call the Dispose() method of the USBDeviceList object that contains the USBDevice objects".
TE0300_SendCommand(handle, cmd, cmd_length, reply, &reply_length, timeout)	TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_SendCommand (ref TE_USB_FX2_USBDevice, ref cmd, ref cmd_length, ref reply, ref reply_length, TIMEOUT_MS)

Dewesoft C++ DLL

Trenz Electronic C# DLL

void ResetFX2FifoStatus(HANDLE handle)
{

cout << endl << "Resetting all FIFOs" << endl;
byte cmd[64], reply[64];

int cmd_length = 64;
int reply_length = 64;

    cmd[0] = 0xA4;//command RESET_FIFO_STATUS
    cmd[1] = 0;//RESET all FIFOs

    if (TE0300_SendCommand(handle, cmd, cmd_length, reply, &reply_length, 1000))
        cout << "Error" << endl;

    cmd[0] = 0xA0;//command INITIALIZE
    cmd[1] = 1;//FIFO mode

    if (TE0300_SendCommand(handle, cmd, cmd_length, reply, &reply_length, 1000))
        cout << "Error" << endl;
}

static void ResetFX2FifoStatus(CyUSBDevice TE_USB_FX2_USBDevice)
{

    if (TE_USB_FX2_USBDevice == null)
    {
        Console.WriteLine("Error,no device is selected");
        return;
    }
    Console.WriteLine("Resetting all FIFOs");
    byte[] cmd = new byte[64];
    byte[] reply = new byte[64];
    int cmd_length = 64;
    int reply_length = 64;

    uint TIMEOUT_MS = 100000;

    cmd[0] = (byte)FX2_Commands.RESET_FIFO_STATUS;
    cmd[1] = 0; //reset all fifos

    if (TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_SendCommand(ref TE_USB_FX2_USBDevice, ref cmd, ref cmd_length, ref reply, ref reply_length, TIMEOUT_MS) == false)
        Console.WriteLine("Error Send Command Reset all fifos");

    cmd[0] = (byte)FX2_Commands.INITALIZE; //0xA0;//command INITIALIZE
    cmd[1] = 1;//FIFO mode

    if (TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_SendCommand(ref TE_USB_FX2_USBDevice, ref cmd, ref cmd_length, ref reply, ref reply_length, TIMEOUT_MS) == false)
        Console.WriteLine("Error Switch Mode Fifo Mode");
}

Dewesoft C++ DLL

Trenz Electronic C# DLL

void ReadData(unsigned int handle)
{

int packetlen = RX_PACKET_LEN;
unsigned int packets = 1200;
byte * data;

unsigned int total_cnt = 0;
unsigned int errors = 0;
data = new byte [RX_PACKET_LEN*packets];
//allocate memory

ResetFX2FifoStatus(handle);
SendFPGAcommand(handle,FX22MB_REG0_START_TX);
//starts test

ElapsedTime.Start();
//StopWatch start

for (unsigned int i = 0; i < packets; i++)
{
packetlen = RX_PACKET_LEN;

if (TE0300_GetData(handle, data+total_cnt, &packetlen, PI_EP6,TIMEOUT_MS))
{

cout << "ERROR" << endl;
errors++;
break;
}
total_cnt += packetlen;
}
TheElapsedTime = ElapsedTime.Stop(false);
//DEBUG StopWatch timer

SendFPGAcommand(handle,FX22MB_REG0_STOP);
//stops test
delete data;
}

static void ReadDataFPGAIntegrity(CyUSBDevice TE_USB_FX2_USBDevice, int BUFFER_SIZE, uint TIMEOUT_MS)
{

if (TE_USB_FX2_USBDevice == null)
{
Console.WriteLine("Error,no device is selected");
return;
}

int packetlen = RX_PACKET_LEN;
int packets = 1200;
byte[] data = new byte[packetlen*packets];
byte[] buffer = new byte[packetlen];
int total_cnt = 0;
int errors = 0;
int PI_EP6 = 6;

bool bResultXfer = false;
ResetFX2FifoStatus(TE_USB_FX2_USBDevice);
SendFPGAcommand(ref TE_USB_FX2_USBDevice, MB_Commands.FX22MB_REG0_START_TX, TIMEOUT_MS);
//starts test
test_cnt = 0;
total_cnt = 0;
Stopwatch stopWatch = new Stopwatch();
stopWatch.Start();

for (int i = 0; i < packets; i++)
{
packetlen = RX_PACKET_LEN;
//fixed (byte* buf = &data[total_cnt])
//bResultXfer = TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_GetDataP(ref inEndpointPipeNo, buf, ref packetlen, PI_EP6, TIMEOUT_MS);
bResultXfer = TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_GetData(ref TE_USB_FX2_USBDevice, ref buffer, ref packetlen, PI_EP6, TIMEOUT_MS,BUFFER_SIZE);
Buffer.BlockCopy(buffer,0, data, total_cnt, packetlen);
if (bResultXfer == false)
{
Console.WriteLine("Error Get Data");
errors++;
break;
}
total_cnt += packetlen;
}
stopWatch.Stop();
TimeSpan ts = stopWatch.Elapsed;

SendFPGAcommand(ref TE_USB_FX2_USBDevice, MB_Commands.FX22MB_REG0_STOP, TIMEOUT_MS);
//stops test
}

Dewesoft C++ DLL

Trenz Electronic C# DLL

void WriteData(unsigned int handle)
{

int packetlen = TX_PACKET_LEN;
unsigned int packets = 1200;
byte * data;

unsigned int total_cnt = 0;
unsigned int errors = 0;
data = new byte [TX_PACKET_LEN*packets];
//allocate memory
//SetData (data);
ResetFX2FifoStatus(handle);
SendFPGAcommand(handle,FX22MB_REG0_START_RX);
//starts test

ElapsedTime.Start();
//StopWatch start

for (unsigned int i = 0; i < packets; i++)
{
packetlen = TX_PACKET_LEN;
if (TE0300_GetData(handle, data+total_cnt, &packetlen, PI_EP8,TIMEOUT_MS))
{

cout << "ERROR" << endl;
errors++;
break;
}
total_cnt += packetlen;
}
TheElapsedTime = ElapsedTime.Stop(false);
//DEBUG StopWatch timer

SendFPGAcommand(handle,FX22MB_REG0_STOP);

//stops test
delete data;
}

static void WriteData(CyUSBDevice TE_USB_FX2_USBDevice, int BUFFER_SIZE, uint TIMEOUT_MS)
{

if (TE_USB_FX2_USBDevice == null)
{
Console.WriteLine("Error,no device is selected");
return;
}

int packetlen = TX_PACKET_LEN;
int packets = 1200;
byte[] data = new byte[packetlen*packets];
byte[] buffer = new byte[packetlen];
int total_cnt = 0;
int errors = 0;
int PI_EP8 = 8;
//SetData (data);
bool bResultXfer = false;
ResetFX2FifoStatus(TE_USB_FX2_USBDevice);
SendFPGAcommand(ref TE_USB_FX2_USBDevice, MB_Commands.FX22MB_REG0_START_RX, TIMEOUT_MS);
//starts test
test_cnt = 0;
total_cnt = 0;
Stopwatch stopWatch = new Stopwatch();
stopWatch.Start();

for (int i = 0; i < packets; i++)
{
packetlen = TX_PACKET_LEN;
Buffer.BlockCopy(data,total_cnt, buffer, 0, packetlen);
bResultXfer = TE_USB_FX2.TE_USB_FX2.TE_USB_FX2_GetData(ref TE_USB_FX2_USBDevice, ref buffer, ref packetlen, PI_EP6, TIMEOUT_MS,BUFFER_SIZE);

if (bResultXfer == false)
{
Console.WriteLine("Error Get Data");
errors++;
break;
}
total_cnt += packetlen;
}
stopWatch.Stop();
TimeSpan ts = stopWatch.Elapsed;

SendFPGAcommand(ref TE_USB_FX2_USBDevice, MB_Commands.FX22MB_REG0_STOP, TIMEOUT_MS);
//stops test
}

Trenz Electronic Documentation

[TE USB Suite]

Page tree

Introduction

Function translation

Trenz Electronic Documentation

[TE USB Suite]

Page tree

UM Porting Guide: Dewesoft C++ DLL to Trenz Electronic C# DLL Porting Guide

Introduction

Function translation