You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 8 Next »

Overview

Refer to http://trenz.org/tei0022-info for the current online version of this manual and other available documentation.

Key Features

  • Quartus Prime Lite 21.1
  • Intel SoC FPGA EDS Standard Edition 20.1
  • Yocto
  • SD
  • UART
  • ETH
  • USB
  • I2C
  • QSPI
  • HDMI
  • MAC from EEPROM
  • DDR3 memory
  • User LED

Revision History

DateQuartusProject BuiltAuthorsDescription
2022-06-xx21.1 Lite
Thomas Dück
  • update to Quartus Prime Lite 21.1
  • bugfixes
2022-04-2620.1.1 Lite

TEI0022-test_board_noprebuilt-quartus_20.1.1-20220426153812.zip

TEI0022-test_board-quartus_20.1.1-20220426153922.zip

Thomas Dück
  • add lock_avalon_base_address command to qsys source files
2022-02-0320.1.1 Lite

TEI0022-test_board_noprebuilt-quartus_20.1.1-20220203152427.zip

TEI0022-test_board-quartus_20.1.1-20220203153430.zip

Thomas Dück
  • initial release
Design Revision History

Release Notes and Know Issues

IssuesDescriptionWorkaroundTo be fixed version
No known issues---------
Known Issues

Requirements

Software

SoftwareVersionNote
Quartus Prime Lite21.1needed
Intel SoC FPGA EDS Standard Edition20.1needed
Yoctodunfelloptional (more information: Yocto KICKstart#Used source files)
Software

Hardware

Complete List is available on <project folder>/board_files/*_board_files.csv

Design supports following modules:

Module ModelBoard Part Short NameYocto Machine NamePCB Revision SupportDDRQSPI FlashEMMCOthersNotes
TEI0022-03*A5_C8_2GBtei0022-a5-c8-2gbREV032GB32MB------

*used as reference

Hardware Modules

Design supports following carriers:

Carrier ModelNotes
---

*used as reference

Hardware Carrier

Additional HW Requirements:

Additional HardwareNotes
USB cable for JTAG/UARTCheck Carrier Board and Programmer for correct type
Monitortested with DELL U2412M
Keyboard--
Mouse--
HDMI cable--
RJ45 ethernet cable--

*used as reference

Additional Hardware

Content

For general structure and usage of the reference design, see Project Delivery - Intel devices

Design Sources

TypeLocationNotes
Quartus

<project folder>/source_files/quartus

<project folder>/source_files/<Board Part Short Name>/quartus

Quartus project will be generated by TE Scripts

optional, source files for specific assembly variants

Yocto<project folder>/source_files/os/yoctoYocto BSP layer template for linux
Design sources

Prebuilt

File

File-Extension

Description

SOPC Information File*.sopcinfoFile with description of the .qsys file to create software for the target hardware
SRAM Object File*.sofRam configuration file
Raw binary file*.rbfFPGA configuration file
Diverse Reports---Report files in different formats
Yocto linux image*.wicLinux image for SD card
Prebuilt files (only on ZIP with prebult content)

Download

Reference Design is only usable with the specified Quartus version. Do never use different versions of Quartus software for the same project.

Reference Design is available on:

Design Flow

Reference Design is available with and without prebuilt files. It's recommended to use TE prebuilt files for first launch.

Trenz Electronic provides a tcl based built environment based on Quartus Design Flow.

See also:


The Trenz Electronic FPGA Reference Designs are TCL-script based projects. To create a project, open a project or program a device execute "create_project_win.cmd" on Windows OS and "create_project_linux.sh" on Linux OS.

TE Scripts are only needed to generate the quartus project, all other additional steps are optional and can also executed by Intel Quartus/SDK GUI. For currently Scripts limitations on Win OS and Linux OS see: Project Delivery - Intel devices → Currently limitations of functionality

  1. Open create_project_win.cmd/create_project_linux.sh:
    'Create Project' GUI example
  2. Select Board in "Board selection"
  3. Click on "Create project" button to create project
    1. (optional for manual changes) Select correct quartus installation path in "<project folder>/settings/design_basic_settings.tcl"
  4. Create and configure your Yocto Linux project, see Yocto KICKstart
    1. Copy the generated meta-<module> folder from <project name>/os/yocto/meta-<module> to the path/to/yocto/poky/ directory
    2. Follow the steps from Yocto KICKstart#Create a project for an Intel FPGA device without running the 'bitbake' command

    3. Add the generated bsp layer meta-<machine> to path/to/yocto/poky/build/conf/bblayers.conf with:

      bitbake-layers add-layer ../meta-tei0022

      Note: The generated meta-tei0022 layer depends on the meta-altera layer (for more information see: Yocto KICKstart#Used source files), so you need to add both bsp layers to bblayers.conf

    4. Redefine the variable MACHINE with 'tei0022-<Board-Part-Short-Name>' in path/to/yocto/poky/build/conf/local.conf. The correct MACHINE name can be found in the #Hardware table.

      sed -i '/^MACHINE/s/MACHINE/#MACHINE/g' conf/local.conf
echo -e '\nMACHINE = "tei0022-<Board-Part-Short-Name>"' >> conf/local.conf

    5. Build the image with following command (the image recipes are located in meta-tei0022/recipes-images/yocto/):

      bitbake tei0022-image-minimal
  5. [optional] Create a debian or ubuntu rootfs with/without desktop environment for this board. For more information and instructions see: Create debian/ubuntu rootfs - Intel devices

Launch

Programming

Check Module and Carrier TRMs for proper HW configuration before you try any design.

SD-Boot mode

  1. Follow the steps described in Reference Designs with Yocto - Intel devices to copy the generated linux image to the SD card.
  2. Set Boot Mode to SD-Boot.
    • see module TRM for correct settings
  3. Insert SD-Card in SD-Slot.

QSPI

Not used on this example.

JTAG

Not used on this example.

Usage

  1. Prepare HW like described on section #Programming
  2. Connect UART USB (most cases same as JTAG)
  3. Power on PCB

UART

  1. Open Serial Console (e.g. PuTTY)

    1. select COM Port

      Win OS: see device manager

      Linux OS: see  dmesg | grep tty  (UART is *USB1)

    2. Speed: 115200
  2. Press reset button
  3. Linux Console:

    1. Login data:

      Note: Wait until Linux boot finished

      Username: root
Password: root

    2. You can use Linux shell now.

      i2cdetect -y -r 1   (check I2C 1 Bus)
udhcpc              (ETH0 check)
lsusb               (USB check)

Monitor

  1. Connect the Monitor to HDMI
  2. Connect the Mouse+Keyboard to USB
  3. Press reset button
  4. If yocto default rootfs is used, the linux console is displayed:

    1. Login data:

      Note: Wait until Linux boot finished

      Username: root
Password: root

    2. You can use Linux shell now.

      i2cdetect -y -r 1   (check I2C 1 Bus)
udhcpc              (ETH0 check)
lsusb               (USB check)
  5. [optional] Ubuntu/Debian desktop will be started automatically (for more information see #Rootfs)

System Design - Quartus

Block Design

The block designs may differ depending on the assembly variant.

Block Design - Project
Block Design - Platform Desginer

HPS Interfaces

Activated interfaces:

TypeNote
DDR--
EMAC1--
QSPI--
SDMMC--
USB1--
UART0--
I2C0--
I2C1--
GPIO35connected to ETH PHY_INT pin
GPIO42connected to USB_RST pin
GPIO43connected to ETH_RST pin
GPIO48connected to CPU_GPIO_0 pin
GPIO53connected to LED_HPS_1 pin
GPIO54connected to LED_HPS_2 pin
GPIO55connected to CPU_GPIO_3 pin
GPIO56connected to CPU_GPIO_2 pin
GPIO57connected to USER_BTN_HPS pin
GPIO58connected to CPU_GPIO_1 pin
GPIO61connected to CPU_GPIO_4 pin


Software Design - Yocto

For Yocto installation and project creation, follow instructions from:

U-Boot

Start with Create a custom BSP layer for Intel SoC or FPGA#Configure u-boot

File location: meta-tei0022/recipes-bsp/u-boot/

Changes:

  • select tei0022 board

    • # CONFIG_TARGET_SOCFPGA_CYCLONE5_SOCDK is not set

    • CONFIG_TARGET_TEI0022=y

  • configure bootcommand (load soc_system.rbf file into the FPGA

    • CONFIG_BOOTCOMMAND="load mmc 0:1 $loadaddr soc_system.rbf; fpga load 0 $loadaddr $filesize; bridge enable; run distro_bootcmd"

  • enable misc_init_r function (need to call TE_read_eeprom_mac function)

    • CONFIG_MISC_INIT_R=y

    • CONFIG_MISC=y

  • MAC from eeprom together with uboot:

    • CONFIG_I2C_EEPROM=y

    • CONFIG_SYS_I2C_EEPROM_ADDR=0x50

    • CONFIG_SYS_I2C_EEPROM_BUS=1

    • CONFIG_SYS_EEPROM_SIZE=256

    • CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=0

    • CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=0

    • CONFIG_SYS_I2C_EEPROM_ADDR_LEN=1

    • CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW=0

  • configure eth

    • CONFIG_PHYLIB=y

    • CONFIG_NETDEVICES=y

    • CONFIG_RGMII=y

    • # CONFIG_MII is not set

  • select device tree
    • CONFIG_DEFAULT_DEVICE_TREE="tei0022_<Board Part Short Name>"
    • CONFIG_DEFAULT_FDT_FILE="tei0022_<Board Part Short Name>.dtb"

Device Tree

Excerpts from test_board/os/yocto/meta-tei0022/recipes-bsp/u-boot/files/tei0022_<Board_Part_Short_Name>/dts/tei0022_<Board_Part_Short_Name>.dts
#include "socfpga_cyclone5.dtsi"
#include "dt-bindings/interrupt-controller/irq.h"
#include <dt-bindings/gpio/gpio.h>

/ {
	chosen {
		bootargs = "earlyprintk";
		stdout-path = "serial0:115200n8";
	};

	axi_dma_clk: axi_dma_clk {
		#clock-cells = <0x0>;
		compatible = "fixed-clock";
		clock-frequency = <100000000>;
		clock-output-names = "axi_dma_clock";
	};

	sys_clk: sys_clk {
		#clock-cells = <0x0>;
		compatible = "fixed-clock";
		clock-frequency = <80000000>;
		clock-output-names = "sys_clock";
	};

	hdmi_pll: hdmi_pll {
		compatible = "altr,altera_iopll-18.1";
		#clock-cells = <1>;
			hdmi_pll_outclk0: hdmi_pll_outclk0 {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <148500000>;
			clock-output-names = "hdmi_pll-outclk0";
		}; 
	};

        vdd: regulator-vdd {
                compatible = "regulator-fixed";
                regulator-name = "fixed-supply";
                regulator-min-microvolt = <1800000>;
                regulator-max-microvolt = <1800000>;
                regulator-always-on;
        };

        vdd_3_3: regulator-vdd {
                compatible = "regulator-fixed";
                regulator-name = "fixed-supply";
                regulator-min-microvolt = <3300000>;
                regulator-max-microvolt = <3300000>;
                regulator-always-on;
        };

        vref: regulator-vref {
                compatible = "regulator-fixed";
                regulator-name = "fixed-supply";
                regulator-min-microvolt = <2500000>;
                regulator-max-microvolt = <2500000>;
                regulator-always-on;
        };

	soc {
		 i2c1: i2c@ffc05000 {
			status = "okay";
			speed-mode = <0>;
			#address-cells = <1>;
			#size-cells = <0>;

			adv7511: adv7511@39 {
				compatible = "adi,adv7511";
				reg = <0x39>, <0x3f>;
				reg-names = "primary", "edid";

				adi,input-depth = <8>;
				adi,input-colorspace = "yuv422";
				adi,input-clock = "1x";
				adi,input-style = <1>;
				adi,input-justification = "right";
				adi,clock-delay = <(0)>;

				avdd-supply = <&vdd>;
				dvdd-supply = <&vdd>;
				pvdd-supply = <&vdd>;
				dvdd-3v-supply = <&vdd_3_3>;
				bgvdd-supply = <&vdd>;

				status = "okay";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						adv7511_in: endpoint {
							remote-endpoint = <&axi_hdmi_out>;
						};
					}; 

					port@1 {
						reg = <1>;	
					};

				}; 
			};
		};

		sys_hps_bridges: bridge@ff200000 {
			compatible = "simple-bus";
			reg = <0xff200000 0x00200000>;
			reg-names = "axi_h2f_lw";
			#address-cells = <2>;
			#size-cells = <1>;
			ranges = <0x00000001 0x00001000 0xff201000 0x00000010>,
				<0x00000001 0x00001010 0xff201010 0x00000010>,
				<0x00000001 0x00001020 0xff201020 0x00000008>,
				<0x00000001 0x00001030 0xff201030 0x00000008>,
				<0x00000001 0x00010000 0xff210000 0x00000800>,
				<0x00000001 0x00020000 0xff220000 0x00010000>;

			jtag_uart: jtag-uart@100001030 {
				compatible = "altr,juart-1.0";
				reg = <0x00000001 0x000001030 0x00000008>;
				interrupts = <0 40 4>;
			};

			sysid: sysid@100001020 {
				compatible = "altr,sysid-1.0";
				reg = <0x00000001 0x00001020 0x00000008>;
			};

			fpga_sw: fpga-sw@100001000 {
				compatible = "altr,pio-1.0";
				reg = <0x00000001 0x00001000 0x00000010>;
				interrupts = <0 41 1>;
				altr,gpio-bank-width = <2>;
				#gpio-cells = <2>;
				gpio-controller;
				interrupt-cells = <1>;
				interrupt-controller;
				altr,interrupt-type = <IRQ_TYPE_EDGE_BOTH>;
			};

			fpga_led: fpga-led@100001010 {
				compatible = "altr,pio-1.0";
				reg = <0x00000001 0x00001010 0x00000010>;
				altr,gpio-bank-width = <2>;
				#gpio-cells = <2>;
				gpio-controller;
			};

			leds {
				compatible = "gpio-leds";

				fpgaled0 {
					label = "fpga_led0";
					gpios = <&fpga_led 0 1>;
				};

				fpgaled1 {
					label = "fpga_led1";
					gpios = <&fpga_led 1 1>;
				};
			};

			hdmi_axi_dmac: axi-dmac@100010000 {
				compatible = "adi,axi-dmac-1.00.a";
				reg = <0x00000001 0x00010000 0x00000800>;
				#dma-cells = <1>;
				interrupt-parent = <&intc>;
				interrupts = <0 42 4>;
				clocks = <&axi_dma_clk 0>;
				status = "okay";

				adi,channels {
					#size-cells = <0>;
					#address-cells = <1>;

					dma-channel@0 {
						reg = <0>;
						adi,source-bus-width = <64>;
						adi,source-bus-type = <0>;
						adi,destination-bus-width = <64>;
						adi,destination-bus-type = <1>;
					};
				};
			};


			hdmi_axi_tx: axi-hdmi-tx@100020000 {
				compatible = "adi,axi-hdmi-tx-1.00.a";
				reg = <0x00000001 0x00020000 0x10000>;
				dmas = <&hdmi_axi_dmac 0>;
				dma-names = "video";
				clocks = <&hdmi_pll_outclk0 0>;
				status = "okay";

				port {
					axi_hdmi_out: endpoint {
						remote-endpoint = <&adv7511_in>;
					};
				};
			};
		};
	};
 };

&gmac1 {

	#address-cells = <1>;
	#size-cells = <0>;

	status = "okay";
	phy-mode = "rgmii";

	ethernet-phy@1 {
		reg = <1>;
		adi,rx-internal-delay-ps = <2000>;
		adi,tx-internal-delay-ps = <2000>;
	};
};

&i2c1 {
	status = "okay";
	clock-frequency = <100000>;
	eeprom: eeprom@50 {
		compatible = "atmel,24c08";
		reg = <0x50>;
	};
};
Excerpts from test_board/os/yocto/meta-tei0022/recipes-kernel/linux/files/dts/tei0022_<Board_Part_Short_Name>.dts
#include "socfpga_cyclone5.dtsi"
#include "dt-bindings/interrupt-controller/irq.h"
#include <dt-bindings/gpio/gpio.h>	

/ {
	chosen {
		bootargs = "earlyprintk";
		stdout-path = "serial0:115200n8";
	};

	axi_dma_clk: axi_dma_clk {
		#clock-cells = <0x0>;
		compatible = "fixed-clock";
		clock-frequency = <100000000>;
		clock-output-names = "axi_dma_clock";
	};

	sys_clk: sys_clk {
		#clock-cells = <0x0>;
		compatible = "fixed-clock";
		clock-frequency = <80000000>;
		clock-output-names = "sys_clock";
	};

	hdmi_pll: hdmi_pll {
		compatible = "altr,altera_iopll-18.1";
		#clock-cells = <1>;
			hdmi_pll_outclk0: hdmi_pll_outclk0 {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <148500000>;
			clock-output-names = "hdmi_pll-outclk0";
		}; 
	};

        vdd: regulator-vdd {
                compatible = "regulator-fixed";
                regulator-name = "fixed-supply";
                regulator-min-microvolt = <1800000>;
                regulator-max-microvolt = <1800000>;
                regulator-always-on;
        };

        vdd_3_3: regulator-vdd {
                compatible = "regulator-fixed";
                regulator-name = "fixed-supply";
                regulator-min-microvolt = <3300000>;
                regulator-max-microvolt = <3300000>;
                regulator-always-on;
        };

        vref: regulator-vref {
                compatible = "regulator-fixed";
                regulator-name = "fixed-supply";
                regulator-min-microvolt = <2500000>;
                regulator-max-microvolt = <2500000>;
                regulator-always-on;
        };


	soc {
		i2c1: i2c@ffc05000 {
			status = "okay";
			speed-mode = <0>;
			#address-cells = <1>;
			#size-cells = <0>;

			adv7511: adv7511@39 {
				compatible = "adi,adv7511";
				reg = <0x39>, <0x3f>;
				reg-names = "primary", "edid";

				adi,input-depth = <8>;
				adi,input-colorspace = "yuv422";
				adi,input-clock = "1x";
				adi,input-style = <1>;
				adi,input-justification = "right";
				adi,clock-delay = <(0)>;

				avdd-supply = <&vdd>;
				dvdd-supply = <&vdd>;
				pvdd-supply = <&vdd>;
				dvdd-3v-supply = <&vdd_3_3>;
				bgvdd-supply = <&vdd>;

				status = "okay";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						adv7511_in: endpoint {
							remote-endpoint = <&axi_hdmi_out>;
						};
					}; 

					port@1 {
						reg = <1>;	
					};

				}; 
			};
		};

		sys_hps_bridges: bridge@ff200000 {
			compatible = "simple-bus";
			reg = <0xff200000 0x00200000>;
			reg-names = "axi_h2f_lw";
			#address-cells = <2>;
			#size-cells = <1>;
			ranges = <0x00000001 0x00001000 0xff201000 0x00000010>,
				<0x00000001 0x00001010 0xff201010 0x00000010>,
				<0x00000001 0x00001020 0xff201020 0x00000008>,
				<0x00000001 0x00001030 0xff201030 0x00000008>,
				<0x00000001 0x00010000 0xff210000 0x00000800>,
				<0x00000001 0x00020000 0xff220000 0x00010000>;

			fpga_sw: fpga-sw@100001000 {
				compatible = "altr,pio-1.0";
				reg = <0x00000001 0x00001000 0x00000010>;
				interrupts = <0 41 1>;
				altr,gpio-bank-width = <2>;
				#gpio-cells = <2>;
				gpio-controller;
				interrupt-cells = <1>;
				interrupt-controller;
				altr,interrupt-type = <IRQ_TYPE_EDGE_BOTH>;
			};

			fpga_led: fpga-led@100001010 {
				compatible = "altr,pio-1.0";
				reg = <0x00000001 0x00001010 0x00000010>;
				altr,gpio-bank-width = <2>;
				#gpio-cells = <2>;
				gpio-controller;
			};

			leds {
				compatible = "gpio-leds";

				fpgaled0 {
					label = "fpga_led0";
					gpios = <&fpga_led 0 1>;
				};

				fpgaled1 {
					label = "fpga_led1";
					gpios = <&fpga_led 1 1>;
				};
			};
			
			sysid: sysid@100001020 {
				compatible = "altr,sysid-1.0";
				reg = <0x00000001 0x00001020 0x00000008>;
			};
			
			jtag_uart: jtag-uart@100001030 {
				compatible = "altr,juart-1.0";
				reg = <0x00000001 0x000001030 0x00000008>;
				interrupts = <0 40 4>;
			};

			hdmi_axi_dmac: axi-dmac@100010000 {
				compatible = "adi,axi-dmac-1.00.a";
				reg = <0x00000001 0x00010000 0x00000800>;
				#dma-cells = <1>;
				interrupt-parent = <&intc>;
				interrupts = <0 42 4>;
				clocks = <&axi_dma_clk 0>;
				status = "okay";

				adi,channels {
					#size-cells = <0>;
					#address-cells = <1>;

					dma-channel@0 {
						reg = <0>;
						adi,source-bus-width = <64>;
						adi,source-bus-type = <0>;
						adi,destination-bus-width = <64>;
						adi,destination-bus-type = <1>;
					};
				};
			};


			hdmi_axi_tx: axi-hdmi-tx@100020000 {
				compatible = "adi,axi-hdmi-tx-1.00.a";
				reg = <0x00000001 0x00020000 0x10000>;
				dmas = <&hdmi_axi_dmac 0>;
				dma-names = "video";
				clocks = <&hdmi_pll_outclk0 0>;
				status = "okay";

				port {
					axi_hdmi_out: endpoint {
						remote-endpoint = <&adv7511_in>;
					};
				};
			};
		};
	};
};

&gmac1 {

	#address-cells = <1>;
	#size-cells = <0>;

	status = "okay";
	phy-mode = "rgmii-id";

	ethernet-phy@1 {
		reg = <1>;
		adi,rx-internal-delay-ps = <2000>;
		adi,tx-internal-delay-ps = <2000>;
	};

};

Kernel

Start with Create a custom BSP layer for Intel SoC or FPGA#Configure linux kernel

File location: meta-tei0022/recipes-kernel/linux/

Changes:

  • for hdmi output

    • CONFIG_AXI_DMAC=y

    • CONFIG_CMA=y

    • CONFIG_DMA_CMA=y

    • CONFIG_CMA_SIZE_MBYTES=128

    • CONFIG_DRM=y

    • CONFIG_DRM_BRIDGE=y

    • CONFIG_DRM_I2C_ADV7511=y

    • CONFIG_DRM_ADI_AXI_HDMI=y

  • set TE boot logo

    • CONFIG_LOGO=y

    • CONFIG_LOGO_TRENZELECTRONICS_CLUT224=y

    • # CONFIG_LOGO_LINUX_MONO is not set

    • # CONFIG_LOGO_LINUX_VGA16 is not set

    • # CONFIG_LOGO_LINUX_CLUT224 is not set

  • config ethernet phy

    • CONFIG_PHYLIB=y

    • CONFIG_ADIN_PHY=y

  • set debug settings

    • CONFIG_DEBUG_LL=y

    • CONFIG_DEBUG_SOCFPGA_UART0=y

    • CONFIG_EARLY_PRINTK=y

Images

Image recipe for minimal console image

File location: meta-tei0022/recipes-images/yocto/

Added packages/recipes:

  • tei0022-rbf

  •  ethtool

  • i2c-tools

  • net-tools

  • usbutils

Rootfs

Optionally it's possible to create a debian or ubuntu rootfs with/without desktop environment for this board. For more information and instructions see: Create debian/ubuntu rootfs - Intel devices

Appx. A: Change History and Legal Notices

Document Change History

To get content of older revision  got to "Change History"  of this page and select older document revision number.

DateDocument Revision

Authors

Description

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • add missing commands to qsys source files
2022-02-08v.6Thomas Dück
  • intial release 20.1
--all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

--
Document change history

Legal Notices

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]



Table of contents



  • No labels