You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 2 Next »

CompanyTrenz Electronic GmbH
PCN NumberPCN-JJJJMMDD
TitlePCN-JJJJMMDD TEXXXX-XX Title
Subject
Issue Date

JJJJMMDD

Products Affected

This change affects all Trenz Electronic TEXXXX SoMs: TEXXXX-XX*.

Affected Product

Replacement
TETE

Changes

#3 Changed DCDC EN5311QI (U24, U25, U26) to MPM3834CGPA and adapted power circuit.

Type: Schematic Change

Reason: EOL of Component.

Impact: None. Increased current output capability. Minor changes in electrical characteristics.

#1 Changed DCDC (U23) from EN6347QI to MPM3860GQW-Z and adapted power circuit.

Type: Schematic Change

Reason: EOL of Component.

Impact: None. Increased current output capability. Minor changes in electrical characteristics.

#4 Changed load switch (Q1) from TPS27082LDDCR to MP5077GG-Z and adapted circuit.

Type: Schematic Change

Reason: BOM Optimization.

Impact: None. Increased current output capability. Minor changes in electrical characteristics.

#1 Added power supervisor (U4) for voltage rail VIN handling.

Type: Schematic Change

Reason: Power handling improvement.

Impact: Power supply starts only if voltage rail VIN is in adequate voltage range.

#8 Changed ferrid bead BKP0603HS121-T (L2...L7, L10...L13) to MPZ0603S121HT000.

Type: Schematic Change

Reason: EOL of Component.

Impact: None.

#8 Changed power sequencing.

Type: Schematic Change

Reason: Follow AMD recommendation.

Impact: Voltage rails start in other order. Voltage supervisor (U4) enables 1V voltage rail (DCDC U23) via signal EN_Module. 1V DCDC (U23) enables 1.8V voltage rail (DCDC U25) via signal PG_1V0. 1.8V DCDC (U25) enables 2.5V (DCDC U24) and DDR_VDD (DCDC U26) voltage rails via signal PG_1V8. Voltage rail 3.3V (load switch Q1) is logical AND-enabled via power good signal PG_2V5_3V3 from voltage rail 2.5V DCDC (U24) and DDR_VDD DCDC (U26) via diode (D4) and CPLD (U6) signal EN_3V3 via diode (D5).

#10 Added additional decoupling capacitors C166...C179.

Type: Schematic Change

Reason: Improve decoupling.

Impact: None.

#10 Added level shifter (U9) and capacitors (C185, C186) to separate power domains for signal FPGA_IO. Added fallback resistor (R91).

Type: Schematic Change

Reason: Improve power domain handling for signal FPGA_IO.

Impact: None.

#9 Added optional diode (D3) between signal nets "PROG_B"and "INIT".

Type: Schematic Change

Reason: Optionally, keep FPGA in reset while signal "PROG_B" is low during initial power-up.

Impact: None.

#5 Added diode (D3) between U21 pin 3 net nRST_in and voltage rail 3.3V.

Type: Schematic Change

Reason: Protect manual reset pin.

Impact: None.

#1 Connected exposed pad for SDIO port expander (U15) to GND.

Type: Schematic Change

Reason: Improve thermal situation.

Impact: None.

#1 Changed power net name from 1.5V to DDR_VDD.

Type: Schematic Change

Reason: Improve name handling.

Impact: None.

#1 Pulled-up board revision signal (FPGA U2 pin H17) and updated board revision documentation.

Type: Schematic Change

Reason: Update revision information.

Impact: None. Firmware reflects it but custom firmware needs to be updated by customer.

#19 Added revision history, block and power diagram. Updated page count and order. 

Type: Documentation Update

Reason: Documentation improvement.

Impact: None.

#11 Changed fiducials to standard fiducial type.

Type: Schematic Change

Reason: Use standard fiducials.

Impact: None.

#10 Removed serial number S/N.

Type: Schematic Change

Reason: EOL of Component.

Impact: None.

#17 Added testpoints TP1...TP41.

Type: PCB Change

Reason: Improve signal monitoring.

Impact: None.

#19 Added serial number box print on bottom overlay.

Type: PCB Change

Reason: Required for manufacturing.

Impact: None.




Method of Identification



Production Shipment Schedule

From XXXXX, after old stock is gone. If the new revision is not suitable for your application and still the former revision of the board is needed, please contact us.


Contact Information

If you have any questions related to this PCN, please contact Trenz Electronics Technical Support at

Disclaimer

Any projected dates in this PCN are based on the most current product information at the time this PCN is being issued, but they may change due to unforeseen circumstances.  For the latest schedule and any other information, please contact your local Trenz Electronic sales office, technical support or local distributor.

This PCN follows JEDEC Standard J-STD-046.

  • No labels