Company | Trenz Electronic GmbH |
---|---|
PCN Number | PCN-20240229 |
Title | TE0713-02 to TE0713-03 Hardware Revision Change |
Subject | Hardware Revision Change |
Issue Date | 2024-03-01 |
Products Affected
This change affects all Trenz Electronic TE0713 SoMs: TE0713-02*.
Affected Product | Replacement |
---|---|
TE0713-02-72C46-A | TE0713-03-72C46-A |
TE0713-02-82C46-A | TE0713-03-82C46-A |
(ED: Tabelle ist fertig!)
Changes
#1
Type:
Reason:
Impact:
#3 Changed DCDC EN63A0QI (U14) to MP8869SGL-Z and adapted power circuit.
Type: Schematic Change
Reason: EOL of Component.
Impact: None. Minor changes in electrical characteristics.
#3 Changed DCDCs TPS82085SIL (U5, U6, U7, U8) to MPM3834CGPA-Z and adapted power circuit.
Type: Schematic Change
Reason: BOM Optimization.
Impact: None. Minor changes in electrical characteristics.
#3 Changed load switch TPS27081ADDCR (Q1) to MP5077GG-Z and adapted circuit.
Type: Schematic Change
Reason: BOM Optimization.
Impact: None. Increased current output capability. Minor changes in electrical characteristics.
#3 Added power supervisor STM6710LWB6F (U12, U13) and connected System controller (U3) pin 25 to net "PG_SENSE" instead of 3.3 V.
Type: Schematic Change
Reason: Improve power monitoring.
Impact: Improved power monitoring circuit by supervising additional voltage rails. If monitored voltages are out of range signal "PG_SENSE" is triggered.
#5 Added diode (D2) between signals "INIT" and "PROG_B".
Type: Schematic Change
Reason: Keep FPGA in reset while signal "PROG_B" is low during initial power-up.
Impact: None.
#5 Added pull-up resistor (R71) for signal "SPI_DQ2".
Type: Schematic Change
Reason: Add external pull-up resistor for write protect functionality.
Impact: None. Improve usable flash options.
#6 Changed inductors from BKP0603HS121-T to MPZ0603S121HT000 for L1, L2, and L3.
Type: BOM Change
Reason: EOL of component.
Impact: None.
#20 Signal trace lengths changed
Type: PCB change
Reason: Result of changes above.
Impact: Changed trace length have to be taken into account in existing designs. The trace length for new revision will be available in TE0713 series pinout generator. Please check if change in trace length still matches your requirements. Adaption of carrier may be necessary.
#5 Added common mode voltage setting resistors (R62, R64, R65, R66) for clock signals "PLL_CLK_P" and "PLL_CLK_N" termination.
Type: Schematic Change
Reason: Improve clock termination.
Impact: None.
#5 Connected signal "RD_N" to FPGA via level translator (U10).
Type: Schematic Change
Reason: Enable 245 Synchronous FIFO Mode.
Impact: None.
#5 Added capacitor (C174) for signal "FTDI_RESET_N".
Type: Schematic Change
Reason: Follow FTDI specification.
Impact: None.
#5 Added pull-up resistor (R76) option and pull-down resistor (R78) option for signal "GPIO_0".
Type: Schematic Change
Reason: Increase setting flexibility for FT600Q.
Impact: None.
#5 Added pull-up resistor (R77) option and pull-down resistor (R79) option for signal "GPIO_1".
Type: Schematic Change
Reason: Increase setting flexibility for FT600Q.
Impact: None.
#5 Added pull-up resistor (R74) (default: fitted) and pull-down resistor (R75) (default: not fitted) for PUDC_B handling for signal "DATA4".
Type: Schematic Change
Reason: Follow AMD recommendation.
Impact: None.
#5 Added pull-up resistor (R63) for signal "OE_N".
Type: Schematic Change
Reason: Disable 245 Synchronous FIFO Mode.
Impact: None.
#5 Added pull-up resistor (R72) for signal "PROG_B".
Type: Schematic Change
Reason: Setup PROGRAM_B_0 functionality externally.
Impact: None.
#5 Added series termination resistor (R70) connecting signals "F_CK" and "FIFO_CLK".
Type: Schematic Change
Reason: Signal termination.
Impact: None.
#5 Added series termination resistor (R73) connecting signals "SPI_SCK" and "SPI_SK".
Type: Schematic Change
Reason: Signal termination.
Impact: None.
#5 Removed testpoints from bottom PCB side for signals "3.3VIN", "RESIN", "JTAGEN", "TMS", "TCK", "TDI", and "TDO".
Type: Schematic Change
Reason: Optimize placement.
Impact: None.
#5 Added testpoints (TP4, TP23, TP24, TP25, ??? TP26).
Type: Schematic Change
Reason: Optimize placement.
Impact: None.
#20 Added legal notices, system and power overview. Updated revision history. Updated page count and order.
Type: Documentation Update
Reason: Documentation improvement.
Impact: None.
Method of Identification
Production Shipment Schedule
From XXXXX, after old stock is gone. If the new revision is not suitable for your application and still the former revision of the board is needed, please contact us.
Contact Information
If you have any questions related to this PCN, please contact Trenz Electronics Technical Support at
- forum.trenz-electronic.de
- wiki.trenz-electronic.de
- support%trenz-electronic.de (subject = PCN-JJJJMMDD)
phone
national calls: 05741 3200-0
international calls: 0049 5741 3200-0
Disclaimer
Any projected dates in this PCN are based on the most current product information at the time this PCN is being issued, but they may change due to unforeseen circumstances. For the latest schedule and any other information, please contact your local Trenz Electronic sales office, technical support or local distributor.
This PCN follows JEDEC Standard J-STD-046.