TE0716 TRM

Download PDF version of this document.

Overview

The Trenz Electronic TE0716 is a commercial-grade SoM (System on Module) based on Xilinx Zynq-7000 SoC XC7Z020, with 1GB of DDR3L-1600 SDRAM, 32MB of SPI flash memory, 10x 12-Bit Low Power SAR ADCs, 512Kb Serial EEPROM, Gigabit Ethernet PHY transceiver, a USB PHY transceiver and powerful switching-mode power supplies for all on-board voltages.

Refer to http://trenz.org/te0716-info for the current online version of this manual and other available documentation.

Key Features

• Xilinx XC7Z020 SoC:
  • Processing system (PS):
    
    • ARM® CortexTM-A9 MPCoreTM with CoreSightTM.
    • L1 Cache: 32KB Instruction, 32KB Data per processor.
    • L2 Cache: 512KB.
  • Programmable logic (PL):
    • Artix-7 FPGA Equivalent.
    • Logic cells: 85K.
    • Look-Up Tables: 53200.
    • Block RAM: 4.9 Mb.
    • DSP slices: 220.
    • Peak DSP performance: 276 GMACs.
    • 2x 12 bit, 1 MSPS ADCs with up to 17 Differential Inputs.
  • 120 x PL HR I/O (48 differential pairs and 24 single-ended).
  • 2x PS MIOs (shared with UART TX/RX ZYNQ-FTDI).
• 1GByte DDR3L SDRAM memory (2 x [256Mbit x 16]), 32-bit wide data bus.
• 32MByte Quad SPI Flash memory.
• MAC address serial EEPROM with EUI-48TM node identity (24AA025E48).
• 512Kb Serial EEPROM memory (CAT24C512).
• 10x 12-Bit Low Power SAR ADCs up to 2 MSPS (NCD98011).
• Gigabit Ethernet transceiver PHY (Marvell 88E1512).
• Highly integrated full-featured hi-speed USB 2.0 ULPI transceiver (Microchip USB3320C-EZK).
• Single chip USB Interface 2.0 High Speed 480Mbs to UART / JTAG(Xilinx License included) (FTDI FT2232H-56Q), including microUSB-B connector.
• 2xUser RGB LEDs (Green), LED FPGA DONE (Green).
• 2 x Tactile Switches (User), 1 x Tactile Switche (Reset).
• Card Connector microSD™.
• On-board high-efficiency DC-DC converters for all voltages used.
• Board Size: 65 x 45 mm.

Block Diagram

Figure 1: TE0716-01 Block Diagram

Main Components

Figure 2: TE0716-01 Main Components

1. Xilinx Zynq XC7Z SoC, U5
2. 4Gbit DDR3/L SDRAM, U13
3. 4Gbit DDR3/L SDRAM, U12
4. 32MByte Quad SPI Flash memory, U7
5. 2Kbit MAC address serial EEPROM with EUI-48TM node identity, U24

Initial Delivery State

Table 1: Initial delivery state of programmable devices on the module.

Configuration Signals

Boot process.

The TE0716 supports QSPI and SD Card boot modes, which is controlled by the insertion of the SD card before powering on.

Reset process.

The nRST signal active low reset input, forces PS_POR_B to apply a master reset of the entire Zynq. This reset could be manually done by pressing a switch. This signal could be also reached by a B2B large connector.

This nRST signal (active low) is also held until all FPGA power supplies set their Power Good signals.

Furthermore, if the FPGA core voltage drops under 0.84V or the 3.3V power supply drops to 2.94V or less, this nRST signal is also activated by the Voltage Monitor.

See more about the Power-on Reset (PS_POR_B) signal in the “Zynq-7000 SoC Technical Reference Manual” (“UG585”).

Signals, Interfaces and Pins

Board to Board (B2B) I/Os

Zynq SoC's I/O banks signals connected to the B2B connectors:

JTAG Interface

JTAG access to the TExxxx SoM through B2B connector JMX.

MIO Pins

Test Points

On-board Peripherals

Quad SPI Flash Memory

On-board 32MByte QSPI flash memory S25FL256S (U7) could be used to store the initial FPGA configuration file. After configuration completes, the remaining free memory can be used for application data storage. All four SPI data lines are connected to the FPGA allowing x1, x2 or x4 data bus widths. Maximum data rate depends on the selected bus width and clock frequency used.

• Part number: S25FL256SAGBHI20
• Supply voltage: 3.3V (2.7V - 3.6V).
• Speed: 133MHz max.
• Temperature: Industrial Range -40°C to +85°C.

ADCs

The TE0716 module has 10x 12-Bit Low Power SAR Analog-to-Digital Converter, fully differential input, signed output, with SPI−compatible interface (NCD98011), which are connected to the FPGA PL BANK34.

• Part number: NCD98011XMXTAG
• Analog supply and ADC reference voltage: 3.3V (1.65V – 3.6V).
• Digital I/O supply voltage: 3.3V (1.65V – 3.6V).
• Differential analog inputs: 1 per ADC.
• Sampling rate: 2 MSPS max.
• SNR: 70dB @1KHz fIN.
• THD: -80dB @1KHz fIN.
• Junction Temperature: Range -40°C to +125°C.

EEPROM

MAC-Address EEPROM

A 2Kbit 24AA025E48 serial EEPROM I2C memory (U24), connected to the BANK501 PSMIOs, contains a globally unique 48-bit node address, which is compatible with EUI-48TM specification. The device is organized as two blocks of 128 x 8-bit memory. One of the blocks, the upper half of the array (80h-FFh), stores the 48-bit node address and is permanently write-protected, while the other block is available for application use.

• Part number: 24AA025E48T-I/OT
• Supply voltage: 1.8V (1.7V - 5.5V).
• FCLK: 100KHz (@VCC=1.8V)
• Temperature: Industrial Range -40°C to +85°C.

General Purpose EEPROM

• The TE0716 module has also a 512Kb Serial EEPROM I2C memory (U21).
• Part number: CAT24C512WI-GT3
• Supply voltage: 1.8V (1.8V - 5.5V).
• FCLK: 100KHz/400KHz/1MHz
• Temperature: Industrial Range -40°C to +85°C.

LEDs

DDR3 SDRAM

The TE0716 module has two 500MByte DDR3L SDRAM chips (U12 & U13) arranged into 32-bit wide memory bus providing total on-board memory size of 1GByte.

• Part number: IS43TR16256BL-125KBLI
• Configuration: 256Mx16.
• Supply voltage: 1.35V (1.5V tolerant).
• Speed: 1.25ns @ CL11 (DDR3-1600)
• Temperature: Industrial Range -40°C to +95°C Tcase.

Ethernet

CAN Transceiver

Clock Sources

Programmable Clock Generator

There is a programmable clock generator on-board (U??) provided in order to generate variable clocks for the module. Programming can be done using I²C via PIN header J??.  The I²C Address is 0x??.

Power and Power-On Sequence

Power Supply

Power supply with minimum current capability of xx A for system startup is recommended.

Power Consumption

* TBD - To Be Determined

Power Distribution Dependencies

Power-On Sequence

Voltage Monitor Circuit

Power Rails

Bank Voltages

Board to Board Connectors

? x ? modules use two or three Samtec Micro Tiger Eye Connector on the bottom side.

• 3 x REF-??????? (compatible to ????????), (?? pins, ?? per row)

  Operating Temperature: -??°C ~ ??°C
  Current Rating: ??A per ContactNumber of Positions: ??
  Number of Rows: ??

Technical Specifications

Absolute Maximum Ratings

Recommended Operating Conditions

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

Physical Dimensions

• Module size: ?? mm × ?? mm.  Please download the assembly diagram for exact numbers.

• Mating height with standard connectors: ? mm.

PCB thickness: ?? mm.

Currently Offered Variants 

Revision History

Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Document Change History

Disclaimer