Table of Contents
Overview
The Trenz Electronic TE0703 Carrier Board is a base-board for 4x5 SoMs, which exposes the MIO- and the PS/PL-pins of the SoM to accessible connectors and provides a whole range of on-board-components to test and evaluate Trenz Electronic 4x5 SoMs.
See page "4 x 5 cm carriers" to get information about the SoMs supported by the TE0703 Carrier Board.
Main Components
- Samtec Razor Beam™ high-speed hermaphroditic 50 positions terminal strip, board to board connector, JB1
- Samtec Razor Beam™ high-speed hermaphroditic 50 positions terminal strip, board to board connector, JB2
- Samtec Razor Beam™ high-speed hermaphroditic 30 positions terminal strip, board to board connector, JB3
- Micro SD card socket with detect switch, J3
- LED indicators D1 and D2
- Mini-USB B connector, J4
- LED indicators D3 and D4
- Configuration DIP switches, S2 (see table under ... section)
- User push button(Reset), S1
- Backplane connector(VG96) placeholder, J1
- Backplane connector(VG96) placeholder, J2
- VCCIO voltage selection jumper block, J5, J8, J9 and J10 (see Power section)
- Trxcom 1000Base-T Gigabit RJ45 Magjack, J14
- USB type A receptacle, J6 (optional micro USB 2.0 type B receptacle available, J12)
- 5 V power connector jack, J13
Key Features
- 2 x VG96 backplane connectors (mounting holes and solder pads)
- SDIO port expander with voltage-level translation
- Micro SD card socket, can be used to boot system
- 4 x user LEDs, 2 x red and 2 x green
- Mini USB connector (USB JTAG and UART interface)
- 1 x user-push button routed to CPLD. By default it is configured as system reset button.
- RJ45 Gigabit Ethernet socket with 4 integrated LEDs.
- USB Host Connector
- Barrel jack for 5 V Power Supply input
- 4 A High-Efficiency Power SoC DC-DC Step-Down Converter(Enpirion EN6347) for 3.3 V Power Supply
- Trenz 4x5 Module Socket (3 x Samtec LSHM series connectors)
- USB JTAG and UART Interface (FTDI FT2232H), compatible with Xilinx Tools (also with many other tools)
- 2 x User configurable DIP switches
Interfaces and Pins
Board to Board (B2B) I/O's
For detailed information about the B2B pin out, please refer to the Master Pinout Table.
Micro SD Card Socket
Micro SD Card socket is not directly wired to the B2B connector pins, but through a Texas Instruments TXS02612 SDIO port expander, which is needed for voltage translation due to the different voltage levels of the Micro SD Card and MIO bank 501 of the Xilinx Zynq 7000 chip. The Micro SD Card has 3.3 V signalling, but the MIO Bank 501 on the Xilinx Zynq 7000 chip is set to 1.8 V. !!! (card detect signal...)
Dual channel USB UART/FIFO
TE0703 has on-board USB 2.0 High Speed UART/FIFO FT2232HQ from FTDI. Channel A can only be used in simple UART mode, Channel B can be used as UART, FIFO, JTAG (MPSSE) or High Speed Serial modes. An standard 256 Byte EEPROM to store custom Configuration settings for FT2232H is available. EEPROM settings can be changed using FTDI provided tools that can be downloaded from FTDI website. See FTDI website for more information.
Ethernet
On-board ethernet jack J14 pins are routed to B2B connector JB1. Ethernet jack J14 LED's are all routed to CPLD Bank 1.
USB Interface
TE0703 board has two physical USB sockets:
- J4 as mini USB type B socket wired to on-board FTDI FT2232H chip.
- J6 as USB type A wired to B2B connector JM3 (there is usually something like SMSC USB3320 or similar USB transceiver on the module).
JTAG Interface
JTAG access to the CPLD and Xilinx Zynq chip is provided via Mini-USB JTAG Interface (FTDI FT2232H) and controlled by DIP switch S2-3.
LED's
There are four LED's onboard:
LED | Color | Description |
---|---|---|
D1 | Red | FTDI UART receive activity |
D2 | Green | FTDI UART transmit activity |
D3 | Red | FL_0 |
D4 | Green | FL_1 |
LED's D3 and D4 are connected to the 4x5 B2B connector pins. Those LEDs can be controlled by FPGA Module
DIP switches
Switch | ON | OFF |
---|---|---|
S2-1 | User configurable, routed to CPLD | User configurable, routed to CPLD |
S2-2 | User configurable, routed to CPLD | User configurable, routed to CPLD |
S2-3 | JTAG enabled for B2B connector JB2 | JTAG enabled for CPLD |
S2-4 | Boot from SD Card | Boot from QSPI flash on module |
Power and Power-On Sequence
Power Supply
Power supply with minimum current capability of 3A for system startup is recommended.
Power Consumption
Power Input Pin | Max Current |
---|---|
VIN | 4A |
Typical value: TE0703-05 + TE0715-01 module. SD micro card inserted. Ethernet connected, link up. System booted into Linux prompt and idling. Average power consumption was 5V / 0.55A.
VCCIO voltage selection jumpers J5, J8, J9 and J10
Refer to the 4x5 Module Integration Guide for VCCIO voltage options.
Jumper J5 | 1-2 | 2-3 | Voltage |
---|---|---|---|
VCCIOA | ON | OFF | 1.8 V |
VCCIOA | OFF | ON | 3.3 V |
Jumper J8 | 1-2 | 2-3 | Voltage |
---|---|---|---|
VCCIOB | ON | OFF | 1.8 V |
VCCIOB | OFF | ON | 3.3 V |
Jumper J9 | 1-2 | 2-3 | Voltage |
---|---|---|---|
VCCIOC | ON | OFF | 1.8 V |
VCCIOC | OFF | ON | 3.3 V |
Jumper J10 | 1-2 | 2-3 | Voltage |
---|---|---|---|
VCCIOD | ON | OFF | 1.8 V |
VCCIOD | OFF | ON | 3.3 V |
Initial Delivery State
Board is shipped in following configuration:
- VCCIO voltage selection jumpers are all set to 1.8 V.
- S1 switch configured as reset button in CPLD.
- Two VG96 backplane connectors are not soldered to the board, but they are included in the package as separate components.
- S2 DIP switches are configured as follows:
Switch | Position | Description |
---|---|---|
S2-1 | ON | Mode control MC1. |
S2-2 | ON | Mode control MC0. |
S2-3 | ON | JTAG enabled for B2B JB1 connector. |
S2-4 | OFF | Boot mode set to QSPI. |
Different delivery configurations are available upon request.
Technical Specifications
Absolute Maximum Ratings
Recommended Operating Conditions
....
Physical Dimensions
Board size: PCB 100mm × 64.5mm. Notice that the mini USB-B jack on the left and ethernet RJ-45 jack on the right are hanging slightly over the edge of the PCB making the total width of the longer side approximately 106mm. Please download the assembly diagram for exact numbers.
Mating height of the module with standard connectors: 8mm
PCB thickness: 1.65mm
Highest parts on the PCB are USB type A jack and ethernet RJ-45 jack, approximately 15mm. Please download the step model for exact numbers.
All dimensions are given in mm.
Operating Temperature Ranges
Commercial grade: 0°C to +70°C.
Industrial grade: -40°C to +85°C.
Board operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Weight
42g - Plain board
13g - VG96 connector x 2
Revision History
Hardware Revision History
Date | Revision | Notes | PCN |
---|---|---|---|
- | 01 | Prototypes | - |
- | 02 | First series boards | - |
- | 03 | Added VCCIO strapping resistors | - |
- | 04 | Corrected FTDI EEPROM connection | - |
07.09.2016 | 05 | Added VCCIO Jumpers |
Hardware revision number is printed on the PCB board next to the module model number separated by the dash.
Document Change History
Date | Rrevision | Contributors | Description |
---|---|---|---|
08.12.2016 | Jan Kumann | Document structure revised. | |
05.12.2016 |
| John Hartfiel | Corrected Boot Mode Table |
06.09.2016 | V.01 | Recreation |
Disclaimer
Data Privacy
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
Document Warranty
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
Limitation of Liability
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
Copyright Notice
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
Technology Licenses
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
Environmental Protection
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH, RoHS and WEEE
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.