Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 5 Next »

Download PDF version of this document.

 

 

Table of Contents

Overview

Trenz Electronic TE0713 is an industrial-grade FPGA module integrating Xilinx Artix-7 FPGA, USB 3.0, 1 GByte of DDR3 SDRAM, 32 MByte Flash memory for configuration and operation, and powerful switching-mode power supplies for all on-board voltages. Numerous configurable I/Os are provided via rugged high-speed strips. All this on a tiny footprint, smaller than a credit card size at very competitive price. All Trenz Electronic SoMs in 4 x 5 cm form factor are mechanically compatible.

Block Diagram

Main Components

  1. Xilinx Artix-7 XC7A series FPGA, U1
  2. ...
  3. ...
  4. System Controller CPLD, Lattice Semiconductor MachXO2-256HC, U3
  5. ...

Key Features

  • Xilinx Artix-7 (15T to 200T) SoM (System on Module)
  • Both industrial and commercial temperature ranges available
  • Rugged for high shock and high vibration resistance
  • 1 GByte DDR3 32-bit SDRAM
  • 32 MByte QSPI Flash memory (with XiP support)
  • Programmable clock generator
    • GTP transceiver clock (default 125 MHz)
    • Fabric clock (default 200 MHz)
  • Plug-on module with 2 × 100-pin and 1 × 60-pin high-speed hermaphroditic strips
  • 142 FPGA I/Os (71 differential pairs) available on board-to-board connectors
  • 4 GTP (multi gigabit transceiver) lanes 
  • External clock input for GTP transceivers via B2B connector
  • On-board high-efficiency DC-DC converters
  • System management and power sequencing
  • eFUSE bit-stream encryption
  • AES bit-stream encryption
  • User configurable LED
  • Evenly-spread supply pins for good signal integrity

Additional assembly options are available for cost or performance optimization upon request.

Initial Delivery State

Programmable unit

Content

Notes

Xilinx Artix-7 FPGANot programmedU1
System Controller CPLDProgrammedU3
SPI Flash OTP areaEmptyU4

SPI Flash main array

EmptyU4
SPI Flash Quad Enable bitSetU4

Signals, Interfaces and Pins

Board to Board (B2B) I/Os

FPGA banks and I/O signals connected to the B2B connectors:

FPGA BankB2B ConnectorI/O Signal CountVoltage LevelNotes
13JM114VCCIO13Supplied by the baseboard.
13JM218VCCIO13Supplied by the baseboard.
13JM32VCCIO13Supplied by the baseboard.
14JM183.3V 
14JM3123.3V 
15JM248VCCIO15Supplied by the baseboard.
15JM22VCCIO15Supplied by the baseboard.
16JM148VCCIO16Supplied by the baseboard.

JTAG Interface

JTAG access to the Xilinx Artix-7 FPGA and System Controller CPLD devices is provided through B2B connector JM2.

JTAG Signal

B2B Pin

TMSJM2-93
TDIJM2-95
TDOJM2-97
TCKJM2-99

JTAGEN pin in B2B connector JM1 is used to select JTAG access for FPGA or SC CPLD:

JTAGENJTAG Access To
LowArtix-7 FPGA
HighSystem Controller CPLD

System Controller I/O Pins

Special purpose pins are connected to System Controller CPLD and have following default configuration:

Pin NameModeFunctionDefault Configuration
PGOODOutputPower goodActive high when all on-module power supplies are working properly.
JTAGENInputJTAG selectLow for normal operation, high for System Controller CPLD access.
EN1InputPower EnableWhen forced low, pulls POR_B low to emulate power on reset.
NOSEQ-No functionNot used.
MODE-No functionNot used.

LEDs

The TE0713-01 module has one LED which is connected to the System Controller CPLD. Once FPGA configuration has completed, it can be used by the user's design. 

LEDColorSC SignalSC PinNotes
D1GreenSYSLED18Exact function is defined by SC CPLD firmware.

Clocking

Si5338 programmable clock generator chip is used to generate clocks with 25 MHz oscillator as input connected to the pin IN3. There is a I2C bus connected between the FPGA bank 14 (master) and clock generator chip (slave) which can be used to program output frequencies. See the reference design for more information.

System Controller CPLD

System Controller CPLD (Lattice MachXO2-256HC, U3) is used to control FPGA configuration process. The FPGA is held in reset (by driving the PROG_B signal low) until all power supplies have stabilized.

By driving signal RESIN to low you can reset the FPGA. This signal can be driven from the user’s baseboard PCB via the B2B connector JM2 pin 18.

Input EN1 is also gated to FPGA reset, should be open or pulled up for normal operation. By driving EN1 low, on-board DC-DC converters will be not turned off.

User can create their own System Controller design using Lattice Diamond software. Once created it can be programmed into CPLD via JTAG interface.

DDR3 SDRAM

The TE0713-01 SoM has two 4 Gbit volatile DDR3 SDRAM ICs (U15 and U19) for storing user application code and data.

  • Part number: IM4G16D3FABG-125I
  • Supply voltage: 1.5V
  • Organization: 32M words x 16 bits x 8 banks
  • Memory speed: limited by Xilinx Artix-7 speed grade and MIG

 Configuration of the DDR3 memory controller in the FPGA should be done using the MIG tool in the Xilinx Vivado Design Suite IP catalog.

Power and Power-On Sequence

Power Supply

Single 3.3V power supply (for both VIN and 3.3VIN power rails) with minimum current capability of 3A for system startup is recommended.

Power Consumption

Typical module power consumption is between 2-3W. Exact power consumption is to be determined.

TE0713-01 module can also be powered by split 5V/3.3V power sources if preferred. In such case apply 5V to B2B connectors VIN pins and 3.3V to 3.3VIN pins, although lowest power consumption is achieved when powering the module from single 3.3V supply. When using split 5V/3.3V supplies the power consumption (and heat dissipation) will rise due to the DC-DC converter efficiency (it decreases when VIN/VOUT ratio rises).

Power-On Sequence

For the highest efficiency of the on-board DC-DC regulators, it is recommended to use same 3.3V power source for both VIN and 3.3VIN power rails. Although VIN and 3.3VIN can be powered up in any order, it is recommended to power them up simultaneously.

It is important that all baseboard I/Os are 3-stated at power-on until System Controller sets PGOOD signal high (B2B connector JM1, pin 30), or 3.3V is present on B2B connector JM2 pins 10 and 12, meaning that all on-module voltages have become stable and module is properly powered up.

See Xilinx datasheet DS181 - "Artix-7 FPGAs Data Sheet: DC and AC Switching Characteristics" for additional information. User should also check related baseboard documentation when choosing baseboard design for TE0713 module.

Power Rails

Power Rail Name

B2B Connector JM1 Pin

B2B Connector JM2 Pin

Direction

Notes

VIN

1, 3, 52, 4, 6, 8InputSoM supply voltage (from the baseboard).
3.3VIN13, 15-InputSoM supply voltage (from the baseboard).
DDR_PWR-19OutputModule internal 1.35V level.

1.8V

39-Output

Module internal 1.8V level. Maximum 300mA available.

3.3V-10, 12OutputModule internal 3.3V level.
VCCIO13-1, 3Input

High-Range bank supply voltage (from the baseboard).

VCCIO15-7, 9InputHigh-Range bank supply voltage (from the baseboard).
VCCIO169, 11-InputHigh-Range bank supply voltage (from the baseboard).
VREF_JTAG-91OutputJTAG reference voltage (3.3V).

Board to Board Connectors

Unable to render {include} The included page could not be found.

Technical Specifications

Absolute Maximum Ratings

Parameter

MinMax

Units

Reference Document

VIN supply voltage

  

V

 
3.3VIN supply voltage  V 

Storage temperature (ambient)

-55

100

°C

See IM4G16D3FABG datasheet.

Recommended Operating Conditions

ParameterMinMaxUnitsReference Document
VIN supply voltage  V 
3.3VIN supply voltage  V 
Assembly variants for higher storage temperature range are available on request.

Physical Dimensions

  • Module size: 50 mm × 40 mm.  Please download the assembly diagram for exact numbers.
  • Mating height with standard connectors: 8mm
  • PCB thickness: 1.6mm
  • Highest part on PCB: approx. 2.5mm. Please download the step model for exact numbers.

All dimensions are shown in millimeters.

Operating Temperature Ranges

Commercial grade: 0°C to +70°C.

Industrial grade: -40°C to +85°C.

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

Weight

21 g Plain module.

8.8 g Set of nuts and bolts.

Revision History

Hardware Revision History

DateRevision

Notes

PCNDocumentation Link
2016-06-30

01

First production revision

 TE0713-01


Hardware revision number is printed on the PCB board together with the module model number separated by the dash.

Document Change History

Date

Revision

Contributors

Description

2017-02-07
Jan KumannInitial document.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


  • No labels