You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

 

Features

  • Single 3.3V input
  • Header for TE0790 JTAG/UART Adapter
  • 20 PIn ARM JTAG header (connected to MIO JTAG 0)
  • 10 Pin I2C header for Silabs Clock Builder Field Programmer
  • Done, Error/Status LEDs
  • One PL GT with SMA connectors
  • One PS GT with SMA connectors
  • GT local loopback
  • PL I/O loopbacks
  • PS I/O loopbacks
  • Boot Mode switches
  • Power control switches to control TE0808 power domains

Recommended Accessories

TesKit is a "Test Fixture" for testing TE0808, most I/O pins are looped back for I/O Connector connectivity testing. For additional testing an LVDS oscillator is providing known clock to GT Reference Clock. SMA Connectors are provided on PL and on PS Connected GT lanes. Connector is provided for direct connection to SiLabs ClockBuilder Pro Field Programmer for Si5345 Programming.

ItemNameVendorSeparate OrderComments
1TE0808 or TE803TrenzTE0808, TE0803 
3TE0790 USB JTAG/UART AdapterTrenzTE0790 
4SMA Cable (50 cm long), 4 pcs   
5mini USB Cable   
6Cables for power (2mm Banana Connector), 2 pcs   
7ClockBuilder Pro ProgrammerSiLabsdigikey / mouser 

NOTE: Kit Content may be different, depending on customer agreements. Positions 1 to 3 are always included.

 Supported Bootmodes are SPI and JTAG.

Getting Started

TesKits are pre-assembled and pre-flashed with initial Flash image, they start up as soon as power (3.3V) is applied.

WARNING: There is no over-voltage protection on TEBT0808, proper power supply must be used!

Power would be around 3W if the ZU+ does not boot (DDR4 not active), with Linux booted (or hello world from DDR4) then power consumption goes up to some 5W, if the junction temperature goes higher power consumption goes up to 6-7W.

Startup procedure

  1. Connect mini-USB Cable to PC
  2. Start terminal 115200 Baud
  3. Connect 3.3V Supply to 2mm Banana Connectors
  4. Turn on power

Depending on initial Flash content either Hello appears, or then Linux does boot.

To restart the boot process press the small push-button on TE0790, it is wired to TE0808 Reset.

 

Manual test

TesKit808, mini-USB cable not connected, 3.3V power applied.

 

TE0790 SWTE0808 RLEDTE0790 GLEDTE0790 RLEDDONEERR
PressedOFFONONOFFOFF
ReleasedOFFONONONON

 

Function Description

GT transceiver have either internal connection or loopbacks or are connected to SMA Connectors. Note that connections to SMA are not AC Coupled!

QUADLaneFunction
B1280on-board loopback
B1280B505 Lane 1
B1281B505 Lane 2
B1282B505 Lane 3
B2280-3on-board loopback
B2290-3on-board loopback
B2300-2on-board loopback
B2303SMA Connectors
B5050SMA Connectors
B5051B128 Lane 0
B5052B128 Lane 1
B5053B128 Lane 2

GT Transceiver connections and loopbacks.

PL I/O has on-board internal loopback an all pins for connectivity testing.

 

UART

UART is available on MIO68, MIO69 via the supplied TE0790 USB Module. TE0808 and TE0803 board parts do not support this settings. They must be changed manually.

Boot Mode Settings

M3M2M1M0Bootmode HexBootmodeNotes
ONONONON0x0PS Main JTAG (TE0790 USB JTAG)Needed for SPI Flash Programming
ONONOFFON0x2SPI Flash (dual parallel, 4bit x 2, 32bit Addressing)Default

 

SPI Flash Programming

Flash programming is supported from SDK GUI, fsbl.elf that is needed is provided in common download area.

NOTE: Boot mode must be set to JTAG before starting Flash Programming.

 See Xilinx AR66715

Reference and Test Designs

Please check Project Delivery first.

Hello World

This works out of the box with Vivado/SDK 2016.1, if you only have EVAL license for ZU+ then it is necessary to export HDF without bitstream.

 

NOTE: 2016.1 Bootgen seems to have small bug, automatically generated BIF file has bitstream partition set to PS as destination device what results in BOOT.BIN that does not load correctly. Make sure it is set to PL. This problem has been fixed in 2016.2

Petalinux

Support in Petalinux 2016.x for ZU+ MPSoC is fully integrated. Vivado HSI flow works, all settings from Vivado Design are imported to SDK and Petalinux to generate a working system with all required software components.

Important: BL31.ELF is needed or Linux would fail with kernel panic. PMU Fimware is not absolutely necessary, without it there would be warnings during Linux boot.

 

Note: if there are no network drivers installed, then linux boot does stop on "Configuring network interfaces..." as workaround special "disable network" application can be installed into petalinux to allow booting with no network.

IBERT

If Si5345 is not programmed then there is only 1 GT Clock available, from 125MHz oscillator on TEBT0808, it does clock B228 CLK0 input, with this clock up to 12 GT can be tested, including the GT that has SMA connectors.

 

IBERT with external Loopback on QUAD228, using 125MHz LVDS clock from TEBT0808 base.

Si5345 Programming

Setup for Si5345 PLL Programming using SiLabs ClockBuilder Pro Field Programmer.

References

 

 

 

  • No labels