Table of contents
CPLD Device with designator U5: LCMX02-1200HC. CC703S is minimum startup design.
- JTAG Management
- UART Management
- Power Management
- Boot Mode Management
- Reset Management
- LED Management
Firmware Revision and supported PCB Revision
See Document Change History
|Name / opt. VHD Name||Direction||Pin||Description|
|CM0||in||76||DIP-S2 / used as JTAG Selection|
|EN1||out||81||B2B Power Enable|
|FL_0||inout||28||LED (D3-red) / Status / not connected on REV02,REV03,REV04|
|FL_1||inout||27||LED (D4-green) / Status / not connected on REV02,REV03,REV04|
|FT_B_TX / BDBUS0||in||139||FTDI UART|
|JTAGEN||120||Enable JTAG access to CPLD for Firmware update (zero: normal IOs, one: CPLD JTAG access). Selectable over S2-3|
|M_TCK||in||131||JTAG from/to FTDI|
|M_TDI||in||136||JTAG from/to FTDI|
|M_TDO||out||137||JTAG from/to FTDI|
|M_TMS||in||130||JTAG from/to FTDI|
|MIO0||in||94||DIP-S4 and B2B Pin / used as Boot Mode|
|MIO12||in||100||B2B-Module UART2 TX|
|MIO13||out||99||B2B-Module UART2 RX|
|MIO14||out||105||B2B-Module UART RX|
|MIO15||in||95||B2B-Module UART TX|
|MODE||out||83||Boot Mode Pin. Switch Boot mode of Module (depends on module)|
|NOSEQ||inout||78||Add Pullup only / currently_not_used|
|PGOOD||inout||82||Add Pullup used for Status / currently_not_used|
|PHY_LED1||out||86||Status / currently_not_used|
|PHY_LED1R||out||92||Status / currently_not_used|
|PHY_LED2||out||85||Status / currently_not_used|
|PHY_LED2R||out||91||Status / currently_not_used|
|PROGMODE||out||104||Enable B2B Module JTAG access to CPLD for Firmware update|
|RESIN||out||119||Module Reset Pin on B2B connector|
|S1||in||114||Push Button / Used as module Reset|
|SD_CD||93||/ currently_not_used / not connected on REV02,REV03,REV04|
|SD_SEL||out||113||set to GND / currently_not_used|
|TCK_B||out||1||JTAG from/to Module|
|TDI_B||out||3||JTAG from/to Module|
|TDO_B / C_TDO||in||2||JTAG from/to Module|
|TMS_B||out||4||JTAG from/to Module|
|ULED1 / LED1||out||117||LED (D1-red) / UART Monitoring|
|ULED2 / LED2||out||115||LED /D2-green) / UART Monitoring|
|X16||in||59||UART2 on VG connector J2|
|X17||out||60||UART2 on VG connector J2|
JTAG signals routed directly through the CPLD to module in B2B connector. Access between CPLD and module can be multiplexed via JTAGEN (logical one for CPLD, logical zero for module).
TE0703 CPLD can be select with JTAGEN (DIP-S2-3).
Module FPGA/CPLD access can be switched with PROGMODE which is driven by CMD0 (DIP-S2-2).CMD0 is pulled up with CPLD.
|OFF||OFF||1||1||Access to TE0703 CPLD|
|OFF||ON||1||0||Access to CPLD of B2B Module|
|ON||OFF||0||1||Access to TE0703 CPLD|
|ON||ON||0||0||Access to FPGA of B2B Module|
EN1 is set to one.
RESIN is driven by S1 (Push Button).
MODE Pin is sourced by MIO. MIO0 connected DIP S2-4 and B2B connector. MIO is pulled up with CPLD and can be set to GND via DIP.
|ON||0||def. SD-CARD Boot(for Zynq Modules)|
MIO14 is driven by BDBUS0 (FTDI RX).
BDBUS1 (FTDI TX) is driven by MIO14 .
MIO13 is driven by X16.
X17 is driven by MIO12.
|LED1 (D1-red)||ON, if CMD0=1 else not FTDI_RXD|
|LED2 (D2-green)||ON, if CMD0=1 else not FTDI_TXD|
Appx. A: Change History and Legal Notices
- REV01 to older REV01
- enable CPLD access to module CPLD over DIP
Document Change History
To get content of older revision got to "Change History" of this page and select older document revision number.
|Date||Document Revision||CPLD Firmware Revision||Supported PCB Revision||Authors||Description|
|Work in progress|
*some unused IOs are not connected
Appx. B: Legal Notices
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
Limitation of Liability
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH, RoHS and WEEE
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.