Table of contents
Firmware for PCB CPLD with designator U18. CPLD Device in Chain: LCMX02-256HC
Firmware Revision and supported PCB Revision
See Document Change History
|Name / opt. VHD Name||Direction||Pin||Bank Power||Description|
|CPLD_IO / XIO||in||17||1.8V||FPGA Bank 45 P28|
|DONE||in||13||1.8V||FPGA Configuration DONE_0 Pin|
|EN_PL||out||20||3.3V||Enable module power|
|F_TCK / C_TCK||out||8||1.8V||JTAG to FPGA|
|F_TDI / C_TDI||out||10||1.8V||JTAG to FPGA|
|F_TDO / C_TDO||in||11||1.8V||JTAG to FPGA|
|F_TMS / C_TMS||out||9||1.8V||JTAG to FPGA|
|JTAGMODE||in||26||3.3V||Enable JTAG access to CPLD for Firmware update (zero: JTAG routed to FPGA, one: CPLD access)|
|/ LED1||out||4||3.3V||green LED D1|
|N.C. / dummy||out||5||3.3V||dummy pin|
|nRST_SC0 / RESIN||in||21||3.3V||B2B Reset_N|
|PROG_B||out||12||1.8V||FPGA Configuration PROGRAM_B_0 Pin|
|SC1||23||3.3V||B2B JM1-32 / 4x5 MODE Pin / currently_not_used|
|SC2||inout||25||3.3V||B2B JM1-30 / 4x5 PGOOD Pin|
|SC3||in||27||3.3V||B2B JM1-28 / 4x5 Power Enable Pin|
|SC4||28||3.3V||B2B JM1-7 / 4x5 No Sequencing Pin / currently_not_used|
|TCK / M_TCK||in||30||3.3V||JTAG from B2B connector|
|TDI / M_TDI||in||32||3.3V||JTAG from B2B connector|
|TDO / M_TDO||out||1||3.3V||JTAG from B2B connector|
|TMS / M_TMS||in||29||3.3V||JTAG from B2B connector|
JTAG signals routed directly through the CPLD to FPGA. Access between CPLD and FPGA can be multiplexed via JTAGEN (logical one for CPLD, logical zero for FPGA).
EN_PL is set to one.
SC2 (PGOOD) is zero if SC3(EN1) zero else high impedance.
RESIN is connected to PROG_B.
PUD_C is set to zero. Internal Pullup on power up, see UG570
Green LED D1.
|********||1||B2B Reset is set to low|
|*****ooo||2||EN1 (power enable) is low|
|****oooo||3||Power problem (use PROG_B pullup to check 1.8V)|
|***ooooo||4||INIT_B low (CRC or IDCODE error, see UG570)|
|*ooooooo||5||Done is low (FPGA not programmed, see UG570)|
|User Defined||6||XIO is connected to LED|
Appx. A: Change History and Legal Notices
REV01 to REV02
- Add 4x5 Module control IOs
- Rework Power
- Rework LED
Document Change History
To get content of older revision got to "Change History" of this page and select older document revision number.
|Date||Document Revision||CPLD Firmware Revision||Supported PCB Revision||Authors||Description|
|REV02||REV01,REV02||CPLD REV02 working in process|
|v.3||REV01||REV01||John Hartfiel||CPLD REV01 , Firmware released 2016-11-02|
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
Limitation of Liability
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH, RoHS and WEEE
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.