You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 19 Next »


Download PDF version of this document.

Table of Contents

Overview

Trenz Electronic TE0728 is an automotive-grade FPGA module integrating a Xilinx Automotive Zynq-7020 FPGA, two 100 Mbit Ethernet transceivers (PHY) , 512 MByte DDR3L SDRAM, 16 MByte Flash memory for configuration and operation, and powerful switching-mode power supplies for all on-board voltages. Numerous configurable I/Os are provided via rugged high-speed strips. 

Within the complete module only Automotive components are installed.

All this in a compact 6 x 6 cm form factor, at the most competitive price.

Refer to http://trenz.org/te0728-info for the current online version of this manual and other available documentation.

Key Features

  • Samtec Tiger Eye Terminal Socket ( 80 pins, 2 rows)
  • Micro SD card socket
  • 3 User LEDs, Red,Yellow, Green
  • Two RJ45 Gigabit Ethernet socket
  • Trenz 6x6 module connector strips (3 x Samtec Tiger Eye series connectors)
  • Barrel Jack for 12V power supply 
  • One user push button

Block Diagram

TE0728 block diagram

Main Components


TE0728 main components
  1. Board to Board Connector, J1-J2-J3
  2. LEDs , D1
  3. CR1220 Backup-Battery holder, B1
  4. SD Card Connector, J10
  5. RJ45 Gigabit Ethernet connector, J7-J8
  6. User push-button, S1
  7.  Jumper, J4
  8. Barrel jack for power supply, J9
  9. Jumper, J11
  10. External connector (VG96) placeholder, J5 / J6

Initial Delivery State

There is no hardware component to be programmed on teh carrier.

Storage device name

Content

Notes




Initial delivery state of programmable devices on the module

Control Signals

Boot Process

Signal

DesignatorB2BJumperBoot Mode

Boot_R

J4

J2-11

Open

QSPI

ShortSD Card
Boot process.

Reset Process

There is a user push button which is used for RESET signal.

Signal

DesignatorB2BActive Level

RESET

S1

J2-7

Active High
Reset process.


Signals, Interfaces and Pins

Board to Board (B2B) I/Os

FPGA bank number and number of I/O signals connected to the B2B connector:


B2B ConnectorInterfacesNumber of I/ONotes
J1

User I/O48 singel ended, 24 differentialConnected to Bank 13
4 Single endedMIO10-13
CANH , CANL2 single endedMIO8, MIO9
J2

User I/O22 singel ended, 11 differential
38 single endedMIO16-53
SoM Control Signals5RESET, RST_OUT, BOOT_R,
JTAG Interface4TCK , TDO, TDI, TMS

J3


User I/O20 Single ended, 10 differentialConnected to Bank 35
34 single ended, 17 differentialConnected to Bankd 33
Ethernet 14 single ended, 2 differentialETH_CTREF , ETH_TD+, ETH_TD- , ETH_RD+, ETH_RD-, ETH_LED1, ETH_LED2, ETH_LED3
Ethernet 24 single ended, 2 differentialETH_CTREF , ETH_TD+, ETH_TD- , ETH_RD+, ETH_RD-, ETH_LED1, ETH_LED2, ETH_LED3
General PL I/O to B2B connectors information

On-board Connector

B2B ConnectorInterfacesNumber of I/ONotes
J5

User I/O48 singel ended, 24 differentialConnected to Bank 13
34 single ended, 17 differentialConnected to Bank 33
J6

User I/O42 singel ended, 21 differential
27 single endedMIO16... MIO39 + MIO 51-53
4 single endedMIO10-13
SoM Control Signals3RESET, RST_OUT, BOOT_R
JTAG Interface4TCK , TDO, TDI, TMS

CANH , CANL

2 single endedMIO8 , MIO9
General PL I/O to B2B connectors information

JTAG Interface

JTAG access to the TE0728 Trenz Module through B2B connector J2.

JTAG Signal

B2B Pin

TMSJ2-12
TDIJ2-10
TDOJ2-8
TCKJ2-6
JTAG pins connection


On-board Peripherals

SD Card Socket

SignalsConnected toB2BNotes
CD/DAT3MIO45J2-31
CMDMIO41J2-29
CLKMIO40_CLKJ2-34
DAT0MIO42J2-37
DAT1MIO43J2-40
DAT2MIO44J2-32
CDMIO46J2-35
WPMIO47J2-33
On board peripherals

RJ45 Connector

Signal ETH1B2BSignal ETH2B2BNotes
ETH1_TD+J3-58ETH2_TD+J3-28Transfer
ETH1_TD-J3-56ETH2_TD-J3-26
ETH1_RD+J3_52ETH2_RD+J3-22Receive
ETH1_RD-J3-50ETH2_RD-J3-20
ETH1_CTREFJ3_57ETH2_CTREFJ3-25
ETH1_LED1J3-55ETH2_LED1J3-23Yellow - Activity
ETH1_LED3J3-51ETH2_LED3J3-19Green - Link
Quad SPI interface MIOs and pins

LEDs

DesignatorColorConnected toB2BActive LevelNote
D1-ARedMIO48J2-30Active high
D1-BYellowMIO49J2-38Active high
D1-CGreenMIO50J2-36Active high
On-board LEDs


Power and Power-On Sequence

Power Supply

Power supply with minimum current capability of 3.5 A for system startup is recommended.

Power Consumption

Power Input PinTypical Current
VIN

TBD*

Power Consumption


* TBD - To Be Determined

Power Distribution Dependencies

add drawIO object here: Attention if you copy from other page, objects are only linked.

Power Distribution

Power-On Sequence

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Power Sequency


Power Supply

Power Rail Name

B2B Connector

DirectionNotes
VI














Module power rails.

Bank Voltages

Bank          

Schematic Name

Voltage

Notes




























Zynq SoC bank voltages.


Board to Board Connectors

6 x 6 modules use two or three Samtec Micro Tiger Eye Connector on the bottom side.

  • 3 x REF-189018-01 (compatible to SEM-140-02-03.0-H-D-A), (80 pins, "40" per row)

    Operating Temperature:-55°C ~ 125°C
    Current Rating: 2.6A per ContactNumber of Positions: 80
    Number of Rows: 2

Absolute Maximum Ratings

Processing System(PS)

SymbolsDescriptionMinMaxUnit
VCCPINTPS internal logic supply voltage-0.51.1V
VCCPAUXPS auxiliary supply voltage-0.52.0V
VCCPLLPS PLL supply-0.52.0V
VCCO_DDRPS DDR I/O supply voltage-0.52.0V
VPREFPS input reference voltage-0.52.0V
VCCO_MIO0PS MIO I/O supply voltage for HR I/O banks-0.53.6V
VCCO_MIO1PS MIO I/O supply voltage for HR I/O banks1.713.45V
PS absolute maximum ratings


Programmable Logic(PL)

SymbolsDescriptionMinMaxUnit
VCCINTPL internal logic supply voltage-0.51.1V
VCCPAUXPL auxiliary supply voltage-0.52.0V
VCCPLLPL PLL supply-0.51.1V
VPREFPL input reference voltage-0.52.0V
VCCOPL supply voltage for HR I/O banks-0.53.6V
VINI/O input voltage for HR I/O banks1.713.45V
PL absolute maximum ratings


Technical Specifications

Absolute Maximum Ratings

ParameterMinMaxUnitsReference Document
VIN supply voltage3.560VTPS54260-Q1 datasheets.
Supply voltage for PS MIO banks1.713.465VSee Xilinx DS187 datasheet.
I/O input voltage for PS MIO banks-0.2VCCO_MIO + 0.20VSee Xilinx DS187 datasheet.
Supply voltage for PS DDR1.141.89VSee Xilinx DS187 datasheet.
I/O input voltage for PS DDR-0.20VCCO_DDR + 0.20VSee Xilinx DS187 datasheet.
Supply voltage for HR I/Os banks1.143.465VSee Xilinx DS187 datasheet.
I/O input voltage for HR I/O banks-0.20VCCIO + 0.20VSee Xilinx DS187 datasheet.
Storage Temperature-40125°CSee Xilinx DS187 datasheet.
Module absolute maximum ratings.


Recommended Operating Conditions

Commercial grade: 0°C to +70°C.

Industrial and automotive grade: -40°C to +85°C.

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.


ParameterMinMaxUnitsReference Document
VIN supply voltage3.560VTPS54260-Q1 datasheets.
Supply voltage for PS MIO banks1.713.465VSee Xilinx DS187 datasheet.
I/O input voltage for PS MIO banks-0.2VCCO_MIO + 0.20VSee Xilinx DS187 datasheet.
Supply voltage for PS DDR1.141.89VSee Xilinx DS187 datasheet.
I/O input voltage for PS DDR-0.20VCCO_DDR + 0.20VSee Xilinx DS187 datasheet.
Supply voltage for HR I/Os banks1.143.465VSee Xilinx DS187 datasheet.
I/O input voltage for HR I/O banks-0.20VCCIO + 0.20VSee Xilinx DS187 datasheet.
Storage Temperature-65150°CSee Xilinx DS187 datasheet.
CAN Transceiver Temperature-40125°CSee Texas Instrument sn65hvd230q-q1 datasheet.
SPI Flash Memory-4085°CSee Cypress S25FL127S datasheet.
DDR3 SDRAM Temperature-4095°C

See Nanya NT5CC256M16CP-DIA datasheet.

Recommended operating conditions.



Physical Dimensions


Physical dimensions drawing
  • Module size: 60 mm × 60 mm.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 7 mm.

  • PCB thickness: 1.6 mm.

Physical Dimension

Variants Currently In Production

Trenz shop TE0728 overview page
English pageGerman page
Trenz Electronic Shop Overview


Revision History

Hardware Revision History

DateRevisionNotePCNDocumentation Link
-01Prototypes--





Hardware Revision History

Hardware revision number is printed on the PCB board next to the module model number separated by the dash.

Document Change History


DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • change list

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


  • No labels