You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 45 Next »

Download PDF version of this document.

Table of Contents

Overview

The Trenz Electronic TEP0002 is a Pmod compatible motor driver board and used for developing BLCD or CD motor driving software.

Wiki Resource page: http://trenz.org/tep0002-info for the current online version of this manual and other available documentation.

Key Features

  • Modules/ SoC FPGA
    • Compatible with Digilent's Pmod interfaces

  • RAM/Storage
  • On Board
    • 1x Current Sensor
    • 1x ADC
    • 2x Terminal Blocks
    • 2x Power Regulators
    • 3x Half-Bridge Drivers
  • Interface
    • 2x Pmod Pin Header (2x6 Pol)
  • Power 
    •  3.3V supply voltage from Pmods
    • Supply current and voltage monitoring
  • Dimension
    • 40 mm x 40 mm

Block Diagram


TEP0002 block diagram

Main Components

TEP0002 main components
  1. 2x6 PMod Header, J2
  2. 2x6 PMod Header, J1
  3. Power Regulators, U1-U7
  4. Half Bridge Gate Drivers, U14-U17-U20
  5. Current Sensors, U15-U18-U21-U46
  6. ARK500-2 connector, J2
  7. ARK500-3 connector, J3
  8. Analog Digital Converter, U16-U19-U22-U47

Initial Delivery State

Storage device name

Content

Notes

---------
Initial delivery state of programmable devices on the module

Configuration Signals

MODE Signal State

Boot Mode

---

---

Boot process.

Signal

B2BI/ONote

---

------
Reset process.

Signals, Interfaces and Pins

Pmod Connectors

TEP0002 is equipped with two 2x6 Pmod Connectors, J1 and J2. 

Pin Pmod J1Pmod J2Notes
1PWM CH0ADC CH
2PWM CH1ADC SCK
3PWM CH2ADC CS
4N.CSensor fault
5GNDGND
6VCCVCC
7EN CH0ADC DO0
8EN CH1ADC DO1
9EN CH2ADC DO2
10N.CADC DO3
11GNDGND
12VCCVCC
General Pmod connectors information

Terminal blocks

The TEP0002 is equipped with two Terminal Blocks J3 and J4.

DesignatorPinSchematicNotes
J31DRV CH2
2DRV CH1
3DRV CH0
J41DC IN
2GND
Terminal Blocks information

On-board Peripherals

Chip/InterfaceDesignatorNotes
ADC

On board peripherals

ADC

PinSchematicConnected toNotes








ADC Information

Power and Power-On Sequence

Power Supply

Power supply with minimum current capability of xx A for system startup is recommended.

Power Consumption

Power Input PinTypical Current
VINTBD*
Power Consumption

* TBD - To Be Determined

Power Distribution Dependencies

Power Distribution

Power-On Sequence

Power Sequency

Voltage Monitor Circuit

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Voltage Monitor Circuit

Power Rails

Power Rail Name

Pmod  J1 Pin

Pmod J2 Pin

DirectionNotes




















Module power rails.

Technical Specifications

Absolute Maximum Ratings

SymbolsDescriptionMinMaxUnit




V










PS absolute maximum ratings

Recommended Operating Conditions

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

ParameterMinMaxUnitsReference Document



VSee ???? datasheets.



VSee Xilinx ???? datasheet.



°CSee Xilinx ???? datasheet.



°CSee Xilinx ???? datasheet.
Recommended operating conditions.

Physical Dimensions

  • Module size: 40 mm × 40 mm.  Please download the assembly diagram for exact numbers.

PCB thickness: 1.59 mm.

Physical Dimension

Currently Offered Variants 

Trenz shop TEP0002 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History


DateRevisionChangesDocumentation Link
2017-03-09REV01
REV01
2018-02-27REV02
REV02
2019-04-23REV03
REV03
Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Board hardware revision number.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • Technical specification update

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • No labels