<!-- Template Revision 1.68 (HTML comments will be not displayed in the document, no need to remove them. For Template/Skeleton changes, increase Template Revision number. So we can check faster, if the TRM style is up to date). --> |
<!-- General Notes: If some section is CPLD firmware dependent, make a note and if available link to the CPLD firmware description. It's in the TE shop download area in the corresponding module -> revision -> firmware folder. --> |
<!-- General Notes: Designate all graphics and pictures with a number and a description. For example "Figure 1: TE07xx-xx Block Diagram" or "Table 1: Initial delivery state". "Figure x" and "Table x" have to be formatted to bold. --> |
<!-- Link to the base folder of the module (remove de/ or en/ from the URL): for example: https://shop.trenz-electronic.de/Download/?path=Trenz_Electronic/Modules_and_Module_Carriers/4x5/4x5_Carriers/TE0703/ --> |
Table of Contents |
The Trenz Electronic TEC0850 is an industrial-grade MPSoC SoM integrating a Xilinx Zynq UltraScale+ MPSoC, with 64-bit wide SODIMM DDR4 SDRAM, max. Dual 512 MByte Flash memory for configuration and operation. 24 Gigabit transceivers on PL side and 4 PS side. Powerful switch-mode power supplies for all onboard voltages. A large number of configurable I/Os. 3U form factor.
<!-- Use short link the Wiki resource page: for example: http://trenz.org/tef1001-info List of available short links: https://wiki.trenz-electronic.de/display/CON/Redirects --> |
Refer to http://trenz.org/tec0850-info for the current online version of this manual and other available documentation. |
...
<!-- Rules for all diagrams: 1. All diagrams are wrapped in the "Scroll Title" macro. - The title has to be named with the diagrams name - The anchor has the designation figure_x, whereby x is the number of the diagram 2. The Draw.IO diagram has to be inserted in the "Scroll Ignore" macro - Border has to be switched off in the macro edit - Toolbar has to be hidden in the macro edit 3. A PNG Export of the diagram has to be inserted in the "Scroll Only" macro, see Wiki page "Diagram Drawing Guidelines" how to do this step. The workaround with the additional PNG of the diagram is necessary until the bug of the Scroll PDF Exporter, which cuts diagram to two pages, is fixed. IMPORTANT NOTE: In case of copy and paste the TRM skeleton to a new Wiki page, delete the Draw.IO diagrams and the PNGs, otherwise due to the linkage of the copied diagrams every change in the TRM Skeleton will effect also in the created TRM and vice versa! See page "Diagram Drawing Guidelines" how to clone an existing diagram as suitable template for the new diagram! --> |
Storage device name | Content | Notes |
---|---|---|
... | ... | .. |
Front panel USB-C Interface connected to USB FIFO bridge chip FT601Q. 32-bit FIFO bridge provides a simple high-speed interface to Zynq UltraScale+ PL.
FT601Q Signal | FPGA Pin |
---|---|
FIFO_CLK | |
... |
See FT600Q-FT601Q IC Datasheet for interface details.
Front panel Micro-USB Interface provides access to UART and JTAG functions via FTDI FT2232 chip. Use of this feature requires that USB driver is installed on your host PC. UART0 with MIO 22 .. 23 should be selected in "Zynq UltraScale+ MPSoC" configuration.
The Digilent plug-in software and cable drivers must be installed on your machine for you to be able to use JTAG interface.
There are some limitations to use SD card Interface in Linux.
To force Linux driver not to use this features add following instructions to device tree file. &sdhci1 { no-1-8-v; |
...
MGT
The TEC0850 board has 30 MGT lines routed to backplane connectors.
Bank | Connector | Lanes |
---|---|---|
PL 128 | J4G and J4H | 4 |
PL 129 | J5A and J5B | 4 |
PL 130 | J5C and J5D | 4 |
PL 230 | J4G and J4H | 4 |
PL 229 | J5A and J5B | 4 |
PL 228 | J5C and J5D | 4 |
PS 505 | J1A | 4 |
MGT reference clocks are connected to banks 129, 229 and 505. Banks 128 and 130 should share clock from bank 129, banks 230 and 228 from bank 229.
USB Interface
Zynq UltraScale+ USB controller connected to backplane connector J1C via USB PHY chip U11.
The Zynq UltraScale+ DDRC hard memory controller is wired to the DDR4 SODIMM Socket U3.
The TEC0850 board is populated with the Zynq UltraScale+ XCZU15EG-1FFVB1156E MPSoC.
Main IO interfaces are shown on the image below.
PS MIO Configuration
MIO | Interface |
---|---|
MIO 0...12 | QSPI Flash Memory |
MIO 20...21 | I2C 1 |
MIO 22...23 | UART 0 |
MIO 26...37 | GEM 0 |
MIO 46...51 | SD 1 |
MIO 52...63 | USB 0 |
MIO 64...75 | USB 1 |
MIO 76...77 | MDIO 0 |
Table 10: Default MIO Configuration
System controller chip is Intel MAX10 10M08SAU169C8G Chip with board control firmware.
I2C
The onboard I2C bus is connected to MIO 20...21 pins. Devices on the bus shown in the table below.
I2C address | Chip | Description |
---|---|---|
0x69 | U14 Si5345 | Clock generator and distributor |
FT2232H
FT601Q-B-T
Board has two N25Q512A11G1240E connected in a dual parallel mode.
I2C
The onboard I2C bus is connected to MIO 20...21 pins. Devices on the bus shown in the table below.
I2C address | Chip | Description |
---|---|---|
0x50 | U63 24AA128T-I/ST | 128K Serial EEPROM |
0x53 | U64 24AA025E48T-I/OT | 2K Serial EEPROM with EUI-48™ or EUI-64™ Node Identity |
Board has Marvell Alaska 88E1512 Ethernet PHY which use MDIO address 1.
Board has 4 8-bit parallel Texas Instruments THS5641 DACs with up to 100 MSPS Update Rate.
S1
Switch | Description |
---|---|
1 | Boot Mode 0 |
2 | Boot Mode 1 |
3 | Boot Mode 2 |
4 | Boot Mode 3 |
See Zynq UltraScale+ Device Technical Reference Manual page 236 for full boot modes description. Most common modes are
Boot Mode | SW1:4 | SW1:3 | SW1:2 | SW1:1 |
---|---|---|---|---|
JTAG Boot Mode | ON | ON | ON | ON |
Quad-SPI | ON | ON | ON | OFF |
SD Card | ON | ON | OFF | OFF |
S2
Switch | Description |
---|---|
1 | SC JTAGEN |
2 | EEPROM WP (Write protect) |
3 | FPGA PUDC |
4 | SC Switch (Reserved for future use) |
LED | Signal | Chip | Pin | Description |
---|---|---|---|---|
Front panel LED 1 (Red) | LED_FP_1 | FPGA U1 | AF15 | PL User defined LED |
Front panel LED 2 (Green) | LED_FP_2 | FPGA U1 | AG15 | PL User defined LED |
Front panel LED 3 (Green) | LED_FP_3 | FPGA U1 | AE15 | PL User defined LED |
Front panel LED 4 (Green) | LED_FP_4 | SC U18 | M4 | Power Good |
<!-- If power sequencing and distribution is not so much, you can join both sub sections together --> |
The maximum power consumption of a module mainly depends on the design running on the FPGA.
Xilinx provide a power estimator excel sheets to calculate power consumption. It's also possible to evaluate the power consumption of the developed design with Vivado. See also Trenz Electronic Wiki FAQ.
Power Input | Typical Current |
---|---|
TBD* |
Table : Typical power consumption.
<!-- Set correct link to the overview table of the product on english and german, if not available, set https://shop.trenz-electronic.de/de/Produkte/Trenz-Electronic/ https://shop.trenz-electronic.de/en/Products/Trenz-Electronic/ --> |
Trenz shop TE0C0850 overview page | |
---|---|
English page | German page |
<!-- Attention link is currently not correct, set if overview table is available! --> |
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
supply voltage... | V | - | ||
Storage temperature | °C | - |
Table : Module absolute maximum ratings.
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
supply voltage... | ||||
Operating temperature |
Table : Module recommended operating conditions.
Board size: ...mm × ...mm. Please download the assembly diagram for exact numbers
PCB thickness: ca. ...mm
The board meets the ... Specification...
All dimensions are given in millimeters.
Date | Revision | Notes | PCN | Documentation Link |
---|---|---|---|---|
- | 02 | current available board revision | - | TEC0850-02 |
- | 01 | First production release | - | - |
Table 24: Module hardware revision history
Hardware revision number can be found on the PCB board together with the module model number separated by the dash.
<!-- Generate new entry: 1.add new row below first 2.Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number 3.Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> |
Date | Revision | Contributors | Description |
---|---|---|---|
| |||
all |