In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are:

  • Overview of the board (point out the LEDs, Ethernets, Switches and etc on the board overview)
  • Explain Switches functionality
  • Explain user LEDs

  • Explain the UART connection

  • Refer to the Reference Design

    For more information regarding how to draw a diagram, Please refer to "Diagram Drawing Guideline" .



Table of Contents

TEBF0808 with TE080x

Overview

Basic instructions to work with TEBF0808 and TE0808,TE0807 or TE0803.

Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area






NumberNoteLetterNote
1Reset Button S2A

PMOD 3.3V I2C

2LEDs D7 Red (Usage: status) and D6 Green (Usage: status)B
3Reset Button S1C
4Power Jack J25, 2.1mm (optional 12V power input)D
5S5 DIP for Boot Mode and FMCVADJE
6Enclosure Pin header(Reset and Power Button, HD LED (Usage: status/user) and Power LED (Usage: status/user))F
7S4 DIP for CPLD access and power controlG
8XMOD J12 with green dot for Module JTAG and UART, XMOD LED D4 Red used  for status informationH
9XMOD J28 for CPLD,FMC JTAG and Firmware ID over UART(need CPLD Firmware 7 or newer) , XMOD LED D4 Red used for status informationI
10FPGA Done LED (location varies slightly depending on module)K
11ATX Power Connector J20 (Main 12V and 5V Power supply), recommended power supply connectorL
12SFP LED D1 Red (Usage: status/user)M
13SFP LED D8 Green (Usage: status/user)N
14SFP LED D9 Red (Usage: status/user)O
15SFP LED D10 Green (Usage: status/user)P
16ETH LED Yellow (Usage: status)Q
17ETH LED Green/Orange (Usage: status)

18LEDs D4 Green (Usage: status/user) and D5 Red (Usage: status/user)

Power supply

The input power supply must be mentioned. Add Link to overview picture with connector label.

Recommended power supply unit is PC power supply unit over connector J20 (Overview - 12)

Optional single 12V power supply over J25 (Overview - 12)

DIP-Switches and Push Buttons

Explain all DIP switches functionality. Add Link to overview picture with connector label.






Jumpers

Explain all Jumpers functionality and connection. Add Link to overview picture with connector label.



LEDs

Explain all user LEDs functionality and connections. Add Link to overview picture with connector label.



Furthermore, there are two user LEDs on module TE0728.

DesignatorColorConnected toNote
D1RedDONE signal (PS Configuration Bank 503)

This LED goes ON when power has been applied to the module and stays ON until MPSoC's programmable logic is configured properly.


JTAG/UART

Explain JTAG or UART connection . Add Link to overview picture with connector label.

SoC JTAG and UART connections are available through XMOD JTAG adapter with the green dot on J12. For more information refer to TE0790.

DIP Switch on the XMOD JTAG adapter must be set like the following table.

DIP SwitchSetting
1ON
2OFF
3OFF
4OFF


CPLD Firmware Update

Boot Mode

Reference Designs

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

Notes

In this Section you must refer to the Resources Page for the particular module.

For Example: TE0728 Resources

Module and Carrier are also as starter kit available: