In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are:
|
Table of Contents |
Basic instructions to work with TEBF0808 and TE0808,TE0807 or TE0803.
Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area |
Number | Note | Letter | Note | |
---|---|---|---|---|
1 | S2- Reset Button | A | P1 - PMOD 3.3V I2C Bus | |
2 | D7 - LED D7 Red (Usage: status) || D6 - LED Green (Usage: status) | B | J9 - Audio Enclosure | |
3 | S1 - Reset Button | C | P3 - PMOD 3.3V I2C Bus | |
4 | J25 - Power Jack J25, 2.1mm (optional 12V power input) | D | J17 - I2C (for optional module PLL access) | |
5 | S5 - DIP Switch for Boot Mode and FMCVADJ | E | J6/15 - Firefly - GTH | |
6 | J10 - Enclosure Pin header(Reset and Power Button, HD LED (Usage: status/user) and Power LED (Usage: status/user)) | F | J31 - SATA | |
7 | S4 - DIP Switch for CPLD access and power control | G | J21/22 - Firefly - loopback only | |
8 | J12 - XMOD with green dot for Module JTAG and UART, XMOD LED D4 Red used for status information | H | J11 - PCIe (1x) | |
9 | J28 - XMOD for CPLD,FMC JTAG and Firmware ID over UART(need CPLD Firmware 7 or newer) , XMOD LED D4 Red used for status information | I | J30 - PJTAG | |
10 | FPGA Done LED (location varies slightly on different module series ) | J | J5 - FMC HPC | |
11 | J20 - ATX Power Connector (Main 12V and 5V Power supply), recommended power supply connector | K | J24 - CAN | |
12 | D1 - SFP LED Red (Usage: status/user) | L | J8 - USB 3.0 (2x) Enclosure | |
13 | D8 - SFP LED Green (Usage: status/user) | M | J27 - SD | |
14 | D9 - SFP LED Red (Usage: status/user) | N | J14 - SFP (2x) | |
15 | D10 - SFP LED Green (Usage: status/user) | O | J7 - USB 3.0 (2x), ETH (1x) | |
16 | J7 - ETH LED Yellow (Usage: status) | P | J13 - Displayport (1x) | |
17 | J7 - ETH LED Green/Orange (Usage: status) | Q | P2 - PMOD 3.3V FPG IOs || Bottom side: J16 - microSD | |
18 | D4 - LED Green (Usage: status/user) || D5 - LED Red (Usage: status/user) |
The input power supply must be mentioned. Add Link to overview picture with connector label. |
Recommended power supply unit is PC power supply unit over connector J20 (Overview - 12)
Optional single 12V power supply over J25 (Overview - 12)
Explain all DIP switches functionality. Add Link to overview picture with connector label. |
|
|
Explain all Jumpers functionality and connection. Add Link to overview picture with connector label. |
Explain all user LEDs functionality and connections. Add Link to overview picture with connector label. |
Furthermore, there are two user LEDs on module TE0728.
|
Explain JTAG or UART connection . Add Link to overview picture with connector label. |
SoC JTAG and UART connections are available through XMOD JTAG adapter with the green dot on J12. For more information refer to TE0790.
DIP Switch on the XMOD JTAG adapter must be set like the following table.
|
In this Section you must refer to the Reference Design (Test board) for the particular module. For Example: TE0728 Reference Designs |
In this Section you must refer to the Resources Page for the particular module. For Example: TE0728 Resources |
Module and Carrier are also as starter kit available: