In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are:

  • Overview of the board (point out the LEDs, Ethernets, Switches and etc on the board overview)
  • Explain Switches functionality
  • Explain user LEDs

  • Explain the UART connection

  • Refer to the Reference Design

    For more information regarding how to draw a diagram, Please refer to "Diagram Drawing Guideline" .



Table of Contents

TEBF0808 with TE080x

Overview

Basic instructions to work with TEBF0808 and TE0808,TE0807 or TE0803.

Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area






NumberNote
LetterNote
1S2- Reset Button
A

P1 - PMOD 3.3V I2C Bus

2D7 - LED D7 Red (Usage: status) || D6 - LED Green (Usage: status)
BJ9 - Audio Enclosure
3S1 - Reset Button
CJ26 - FAN1 12V
4J25 - Power Jack J25, 2.1mm (optional 12V power input)
DJ17 - I2C (for optional module PLL access)
5S5 - DIP Switch for Boot Mode and FMCVADJ
EJ6/15 - Firefly - GTH
6J10 - Enclosure Pin header(Reset and Power Button, HD LED (Usage: status/user) and Power LED (Usage: status/user))
F

J31 - SATA

7S4 - DIP Switch for CPLD access and power control
GJ21/22 - Firefly - loopback only
8J12 - XMOD with green dot for Module JTAG and UART, XMOD LED D4 Red used  for status information
HP3 - PMOD 3.3V I2C Bus
9J28  - XMOD for CPLD,FMC JTAG and Firmware ID over UART(need CPLD Firmware 7 or newer) , XMOD LED D4 Red used for status information
IJ34 - I2C Firefly
10FPGA Done LED (location varies slightly on different module series )
JJ35 - FAN2 12V
11J20  - ATX Power Connector (Main 12V and 5V Power supply), recommended power supply connector
KJ11 - PCIe (1x)
12D1 - SFP LED Red (Usage: status/user)
LB1 - Battery holder CR1220
13D8  - SFP LED Green (Usage: status/user)
MJ30 - PJTAG
14D9  - SFP LED Red (Usage: status/user)
NJ29 - CAN (same as J24)
15D10  - SFP LED Green (Usage: status/user)
OJ5 -  FMC HPC
16J7 - ETH LED Yellow (Usage: status)
PJ19 - FAN3 5V
17J7 - ETH LED Green/Orange (Usage: status)
QJ24 - CAN (same as J29)
18D4 - LED Green (Usage: status/user) || D5 - LED Red (Usage: status/user)
RJ27 - SD



SJ8 - USB 3.0 (2x) Enclosure



TJ14 - SFP (2x)



UJ7 - USB 3.0 (2x), ETH (1x)



VJ13 - Displayport (1x)



WP2 - PMOD 3.3V FPG IOs



W(b)Bottom side: J16 - microSD

Power supply

The input power supply must be mentioned. Add Link to overview picture with connector label.

Recommended power supply unit is PC power supply unit over connector J20 (Overview - 12)

Optional single 12V power supply over J25 (Overview - 12)

DIP-Switches and Push Buttons

Explain all DIP switches functionality. Add Link to overview picture with connector label.


Overview 7DefaultDescription
S4-1OFFSoC PUDC, ON (low - internal FPGA pull ups enabled), OFF (high - internal FPGA pull ups disabled)
S4-2OFFN.C.
S4-3OFFJTAGEN  ON (CPLD access), OFF (FMC access)
S4-4ONEnable on board 5V permanently



Overview 5DefaultDescription
S5-1ON
  • ON(1), ON(2) - Default, boot from SD/microSD or SPI Flash if no SD is detected
  • OFF(1), ON(2) - Boot from eMMC
  • ON(1), OFF(2) - Boot mode  PJTAG0
  • OFF(1), ON(2) -Boot mode main  JTAG
S5-2ON
S5-3OFFUser Input over RGPIO
S5-4OFFVADJ OFF(1.8V), ON(1.2V)




Jumpers

Explain all Jumpers functionality and connection. Add Link to overview picture with connector label.



LEDs

Explain all user LEDs functionality and connections. Add Link to overview picture with connector label.



Furthermore, there are two user LEDs on module TE0728.

DesignatorColorConnected toNote
D1RedDONE signal (PS Configuration Bank 503)

This LED goes ON when power has been applied to the module and stays ON until MPSoC's programmable logic is configured properly.


JTAG/UART

Explain JTAG or UART connection . Add Link to overview picture with connector label.

SoC JTAG and UART connections are available through XMOD JTAG adapter with the green dot on J12. For more information refer to TE0790.

DIP Switch on the XMOD JTAG adapter must be set like the following table.

XMOD DIP SwitchSetting
1ON
2OFF
3OFF
4OFF


CPLD Firmware Update

Boot Mode

Reference Designs

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

Notes

In this Section you must refer to the Resources Page for the particular module.

For Example: TE0728 Resources

Module and Carrier are also as starter kit available: