Table of Contents
TEIB0006 with TEI0006
Overview
Basic instructions to work with TEIB0006 and TEI0006.
Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area
Number | Note |
---|---|
1 | J1/3 - SFP+ connector |
2 | J14 - CRUVI connector |
3 | J12 - Power Jack, 2.0mm, DC (12V power input) |
4 | J5 - RJ45 Ethernet Connector |
5 | J5 - RJ45 Ethernet Connector LED yellow |
6 | J5 - RJ45 Ethernet Connector LED green |
7 | D1 - LED red || D2 - LED green || D3 - LED green || D4 - LED green |
8 | J8 - USB 2.0 Micro B Receptacle |
9 | J13 - USB 3.0 Micro B Receptacle |
10 | S1 - DIP Switch for JTAG access and write protection for EEPROM U13 on TEIB0006 |
11 | S5 - reset button for Intel MAX 10 on TEI0006 |
12 | S4 - user button |
13 | S3 - reset button for Intel Cyclone 10 GX on TEI0006 |
14 | D2 - LED red || D3 - LED red || D4 - LED green |
15 | J6 - FMC HPC connector |
Power supply
Label | Designator | Supply Voltage | Description |
---|---|---|---|
Overview - 3 | J12 | 12V | Single 12V power supply |
Current depends mainly on design and cooling solution. Use Quartus Power Analyzer Tool and/or Your Quartus Project to estimate min current. Minimum of 1A are recommanded for basic functionality.
DIP-Switches and Push Buttons
Overview 10 | Default | Description |
---|---|---|
S1-1 | ON | JTAGEN - ON = Intel Cyclone 10 GX, OFF = Intel MAX 10 |
S1-2 | OFF | WP = write-protect for EEPROM U13 on TEIB0006 - ON = read and write, OFF = only read |
S1-3 | OFF | not connected |
S1-4 | OFF | not connected |
Overview 11;12;13 | Default | Description |
---|---|---|
S3 | High | reset button for Intel Cyclone 10 GX, connected to:
|
S4 | High | user button, connected to:
|
S5 | High | reset button for Intel MAX 10, connected to:
|
*Note: Reset button S5 is not Firmware depended
LEDs
Label | Designator | Color | Usage | Description |
---|---|---|---|---|
Overview - 5 | J5 | yellow | status | connected to Ethernet phy on TEI0006 |
Overview - 6 | J5 | green | status | connected to Ethernet phy on TEI0006 |
Overview - 14 | D2 | red | status | connected to reset button S3 |
Overview - 14 | D3 | red | --- | connected to user button S4 |
Overview - 14 | D4 | green | status | connected to VOUT (5V) from power module U28 on TEIB0006 |
*Note: LED D4 is not Firmware depended
Label | Designator | Color | Usage | Description |
---|---|---|---|---|
Overview - 7 | D1 | red | status | connected to nSTATUS pin from Intel Cyclone 10 GX |
Overview - 7 | D2 | green | user defined | connected to nfault status of power sequencer ip in Intel MAX10 |
Overview - 7 | D3 | green | user defined | connected to DATA0 pin from Intel Cyclone 10 GX |
Overview - 7 | D4 | green | user defined | connected to DATA0 pin from Intel Cyclone 10 GX |
JTAG/UART
Label | Designator | Description |
---|---|---|
Overview - 8 | J8 | JTAG/UART over USB, UART Speed depends on design, normally 115200 |
CPLD Firmware
Firmware update instruction and Firmware description are available on TEI0006 Intel MAX 10 Firmware. Source code of the firmware is available on the download area of the TEI0006.
Reference Designs
Link to different Reference Designs (Descriptions and Download)
It's recommended to use prebuilt *.jic file of newest Reference Design for first test. Basic Steps:
- Power Supply over 12V power jack
- Download Reference Design
- Open Quartus Prime
- Open Quartus Programmer from top menu: Tools → Programmer
- Select from Programmer top menu: Edit → Hardware Setup
- Select via the drop down menu: Arrow-USB-Blaster [USB0] (Installation of Arrow USB Programmer Driver needed) and close the window
- Click Add File...
- Select correct *.jic file and press Open
- Click Start to program the device
- Open Putty with correct COM port and Speed
- Press reset button S3
- For more details check Reference Design description
Notes
Links to all documentation and download resources: