Table of Contents

TEIB0006 with TEI0006

Overview

Basic instructions to work with TEIB0006 and TEI0006.

Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area


NumberNote
1J1/3 - SFP+ connector
2J14 - CRUVI connector
3J12 - Power Jack, 2.0mm, DC (12V power input)
4J5 - RJ45 Ethernet Connector
5J5 - RJ45 Ethernet Connector LED yellow
6J5 - RJ45 Ethernet Connector LED green
7D1 - LED red  || D2 - LED green || D3 - LED green || D4 - LED green
8J8 - USB 2.0 Micro B Receptacle
9J13 - USB 3.0 Micro B Receptacle
10S1 - DIP Switch for JTAG access and write protection for EEPROM U13 on TEIB0006
11S5 - reset button for Intel MAX 10 on TEI0006
12S4 - user button
13S3 - reset button for Intel Cyclone 10 GX on TEI0006
14D2 - LED red  || D3 - LED red || D4 - LED green
15J6 - FMC HPC connector

Power supply

LabelDesignatorSupply VoltageDescription
Overview - 3J1212VSingle 12V power supply

Current depends mainly on design and cooling solution. Use Quartus Power Analyzer Tool and/or Your Quartus Project to estimate min current. Minimum of 1A are recommanded for basic functionality.

DIP-Switches and Push Buttons

Overview 10DefaultDescription
S1-1ONJTAGEN - ON = Intel Cyclone 10 GX, OFF = Intel MAX 10
S1-2OFFWP = write-protect for EEPROM U13 on TEIB0006 - ON = read and write, OFF = only read
S1-3OFFnot connected
S1-4OFFnot connected
DIP Switches S1


Overview 11;12;13DefaultDescription
S3High

reset button for Intel Cyclone 10 GX, connected to:

  • nCONFIG pin (Intel Cyclone 10 GX)
  • D2 - LED red (TEIB0006)
S4High

user button, connected to:

  • D3 -  LED red (TEIB0006)
  • vin_fault input of power sequencer ip in Intel MAX10
S5High

reset button for Intel MAX 10, connected to:

  • nCONFIG pin (Intel MAX10)

*Note: Reset button S5 is not Firmware depended

Buttons (CPLD Firmware depended)

LEDs


LabelDesignatorColorUsageDescription
Overview - 5J5yellowstatusconnected to Ethernet phy on TEI0006
Overview - 6J5

green

statusconnected to Ethernet phy on TEI0006
Overview - 14D2redstatusconnected to reset button S3
Overview - 14D3red---connected to user button S4
Overview - 14D4greenstatusconnected to VOUT (5V) from power module U28 on TEIB0006

*Note: LED D4 is not Firmware depended

Carrier LEDs (CPLD Firmware depended)


LabelDesignatorColorUsageDescription
Overview - 7D1redstatus

connected to nSTATUS pin from Intel Cyclone 10 GX

Overview - 7D2greenuser definedconnected to nfault status of power sequencer ip in Intel MAX10
Overview - 7D3greenuser definedconnected to DATA0 pin from Intel Cyclone 10 GX
Overview - 7D4greenuser definedconnected to DATA0 pin from Intel Cyclone 10 GX
Module LEDs (CPLD Firmware depended)

JTAG/UART

LabelDesignatorDescription
Overview - 8J8JTAG/UART over USB, UART Speed depends on design, normally 115200

CPLD Firmware

Firmware update instruction and Firmware description are available on TEI0006 Intel MAX 10 Firmware. Source code of the firmware is available on the download area of the TEI0006.

Reference Designs

Link to different Reference Designs (Descriptions and Download)


It's recommended to use prebuilt *.jic file of newest Reference Design for first test. Basic Steps:

  1. Power Supply over 12V power jack
  2. Download Reference Design
  3. Open Quartus Prime
  4. Open Quartus Programmer from top menu: Tools → Programmer
  5. Select from Programmer top menu: Edit → Hardware Setup
  6. Select via the drop down menu: Arrow-USB-Blaster [USB0] (Installation of Arrow USB Programmer Driver needed) and close the window
  7. Click Add File...
  8. Select correct *.jic file and press Open
  9. Click Start to program the device
  10. Open Putty with correct COM port and Speed
  11. Press reset button S3
  12. For more details check Reference Design description


Notes

Links to all documentation and download resources:


  • No labels