some sources available on public doc TEBT0808 TRM
Download PDF version of this document.
Table of Contents
Overview
The Trenz Electronic TEBT0808-01 is a testboard for module TE0808 (REV 02 and 03) as well as for TE0803 (REV 01).
Refer to http://trenz.org/tebt0808-info for the current online version of this manual and other available documentation.
Key Features
- Accepts TE0808 / TE0803
- Single 3.3V input
- Header for TE0790 JTAG/UART Adapter
- 20 Pin ARM JTAG header (connected to MIO JTAG 0)
- 10 Pin I2C header for Silabs Clock Builder Field Programmer
- Done, Error/Status LEDs
- One PL GT with SMA connectors
- One PS GT with SMA connectors
- GT local loopback
- PL I/O loopbacks
- PS I/O loopbacks
- Boot Mode switches
- Power control switches to control TE0808 power domains
- One pre-assembled TE0790 XMOD FTDI JTAG adapter
Supported Bootmodes are SPI and JTAG.
Block Diagram
Main Components
- Uninsulated 2 mm rigid socket. J8-J7
- SMA Coaxial straight. J6- J9...15
- Surface Mount Schottky Barrier Rectifier. D1
- Box Headers, Straight/Angled J5-J16
- Board to Board Connector. J1...4
- Clock Oscillator, U2
- On-Board LED, D2...4
- DIP-Switch, S1...3
- XMOD JTAG Base,
Initial Delivery State
Storage device name | Content | Notes |
---|---|---|
Configuration Signals
Boot mode can be set by DIP-Switch S1.
M3 | M2 | M1 | M0 | Bootmode Hex | Bootmode | Notes |
---|---|---|---|---|---|---|
ON | ON | ON | ON | 0x0 | PS Main JTAG (TE0790 USB JTAG) | Needed for SPI Flash Programming |
ON | ON | OFF | ON | 0x2 | SPI Flash (dual parallel, 4bit x 2, 32bit Addressing) | Default |
Signal | B2B | Note |
---|---|---|
PLL_RST | J2-89 | |
SRST_B | J2-96 | connected to PJTAG0_SRST - J16 |
Signals, Interfaces and Pins
Board to Board (B2B) I/Os
FPGA bank number and number of I/O signals connected to the B2B connector:
B2B Connector | Interfaces | Number of I/O | Notes |
---|---|---|---|
J1 | User I/O | 22 singel ended, 11 Differential 8 singel ended, 4 Differential 8 singel ended, 4 Differential 8 singel ended, 4 Differential 3 singel ended | Connected to Bank 66 Connected to Bank 228 Connected to Bank 229 Connected to Bank 230 VCCO_66, PL_1V8 |
J2 | Ethernet PHY | 32 singel ended, 16 Differential 4 singel ended, 16 Differential | Connected to Bank 505 Connected to Bank 128 |
Control Signals | 15 single ended | PLL_SEL0, PLL_SEL1, PLL_RST, EN_GTR, EN_PL, PLL_LOLN, EN_PSGT, ERR_STATUS, ERR_OUT,SRST_B, INIT_B, PROG_B, EN_FPD , EN_LPD , DONE | |
Power Control Signal | 10 single ended | EN_PLL_PWR, PLL_FINC ,PG_PLL_1V8, LP_GOOD, PG_DDR, PG_PL, PG_FPD, PG_PSGT, PG_GT_R, PG_GT_L | |
JTAG Interface | 7 single ended | TCK, TDI, TMS, TDO, MR, Rxd, Txd | |
WANNE2 | 2 single ended | PLL_SCL, PLL_SDA | |
Clock | 6 singel ended, 3 Differential | CLK0, CLK7, CLK8 | |
J3 | User I/O | 12 singel ended, 6 Differential 12 singel ended, 6 Differential | Connected to Bank 48 Connected to Bank 47 |
Clock | 6 singel ended, 3 Differential | CLK228, CLK229, CLK230 | |
PJTAG Interface | 7 single ended | PJTAG0_TCK, PJTAG0_TDI, PJTAG0_TMS, PJTAG0_TDO, | |
MIO | 27 single ended | MIO19..76 | |
UART | 2 single ended | TXD, RXD | |
Power pins | 4 single ended | PS_1V8, SI_PLL_1V8, VCCO_48, VCCO_47 | |
J4 | User I/O | 48 singel ended, 62 Differential 4 single ended | Connected to Bank 64 Connected to Bank 64 |
Power pins | 4 single ended | VCCO_64, VCCO65 |
JTAG Interface
JTAG access to the TE0803 or TE0808 SoM through B2B connector JM2.
JTAG Signal | B2B Connector |
---|---|
TMS | J2-126 |
TDI | J2-122 |
TDO | J2-124 |
TCK | J2-120 |
MR | J2-83 |
RXD | J3-141 |
TXD | J3-139 |
On-board Peripherals
Chip/Interface | Designator | Notes |
---|---|---|
DIP Switch
There are thre DIP Switches, S1, S2, S3.
The Boot Mode can be set through DIP Switch S1, refer to BootMode table.
Signals | B2B | S1 switch | Notes |
---|---|---|---|
MODE0 | J2-109 | S1A | |
MODE1 | J2-107 | S1B | |
MODE2 | J2-105 | S1C | |
MODE3 | J2-103 | S1D |
Control signals must be set by DIP Switch S2, S3.
Signals | B2B | S2 switch | Notes |
---|---|---|---|
EN_PSGT | J2-84 | S2A | |
EN_GT_R | J2-95 | S2B | |
EN_GT_L | J2-97 | S2C | |
EN_PLL_PWR | J2-77 | S2D | connected to PG_PL |
Signals | B2B | S3 switch | Notes |
---|---|---|---|
EN_DDR | J2-112 | S3A | |
EN_LPD | J2-108 | S3B | |
EN_PL | J2-101 | S3C | |
EN_FPD | J2-102 | S3D |
LEDs
Designator | Color | Connected to | Active Level | Note |
---|---|---|---|---|
D2 | Red | DONE | Low | |
D3 | Red | ERR_STATUS | Low | |
D4 | Red | ERR_OUT | Low |
Clock Sources
Designator | Description | Frequency | Note |
---|---|---|---|
U2 | MEMS Oscillator | 125.00 MHz |
Power and Power-On Sequence
Power Supply
TestKits are pre-assembled and pre-flashed with initial Flash image, they start up as soon as power (3.3V) is applied.
Power Consumption
Power Input Pin | Typical Current |
---|---|
VIN | TBD* |
* TBD - To Be Determined
Power Distribution Dependencies
Power Rails
Power Rail Name | B2B JM1 Pin | B2B JM2 Pin | B2B JM3 Pin | B2B JM4 Pin | Direction | Notes |
---|---|---|---|---|---|---|
VCCO_66 | 90,120 | - | - | - | Output | Connected to 1.8 (PL_1V8) |
3.3V | - | 138...160 | - | - | Input | |
PS_BATT | - | 125 | - | - | Output | Connected to 1.8 (PS_1V8) |
VCCO_47 | - | - | 43, 44 | - | Output | Connected to SI_PLL_1V8 |
VCCO_48 | - | - | 15,16 | - | Output | Connected to SI_PLL_1V8 |
PS_1V8 | - | - | 147, 148 | - | Output | |
PLL_3V3 | - | - | 152 | - | Output | 3.3V |
VCCO_64 | - | - | - | 58,106 | Output | Connected to 1.8 (PL_1V8) |
VCCO_65 | - | - | - | 69,105 | Output | Connected to 1.8 (PL_1V8) |
Board to Board Connectors
TEBT0808 has four Razor Beam™ LP Slim Terminal Strip.
- 3x REF-192552-02 (160-pins)
- ST5 Mates with SS5
5.2 x 7.6 cm SoM Kintex carrier use three Samtec Razor Beam LP Socket Strip (SS5) on the top side.
- 3x REF192552-01 (160-pins)
- SS5 Mates with ST5
Technical Specifications
Absolute Maximum Ratings
Symbols | Min | Max | Unit | Note |
---|---|---|---|---|
VIN | 0 | 3.3 | V | Input Supply Voltage |
Storage Temperatur | -40 | +85 | °C |
Recommended Operating Conditions
Operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Symbols | Min | Max | Unit | Note |
---|---|---|---|---|
VIN | 0 | 3.3 | V | Input Supply Voltage |
Storage Temperatur | -40 | +85 | °C |
Physical Dimensions
Module size: 90 mm × 90 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 3.5 mm.
PCB thickness: 1.6 mm.
Currently Offered Variants
Trenz shop TE0728 overview page | |
---|---|
English page | German page |
Revision History
Hardware Revision History
Date | Revision | Changes |
---|---|---|
- | 01 | - |
Document Change History
Date | Revision | Contributor | Description |
---|---|---|---|
| |||
-- | all |
|
Disclaimer
Data Privacy
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
Document Warranty
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
Limitation of Liability
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
Copyright Notice
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
Technology Licenses
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
Environmental Protection
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH, RoHS and WEEE
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.