You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Next »

Table of Contents

TEBF0808 with TE080x

Overview

Basic instructions to work with TEBF0808 and TE0808,TE0807 or TE0803.

Functionality of buttons, DIP switches, LEDs depends on CPLD Firmware. Following description is only for newest firmware version, which is available on the download area


Board Overview
NumberNote
LetterNote
1S2- Reset Button
A

P1 - PMOD 3.3V I2C Bus

2D7 - LED D7 Red (Usage: status) || D6 - LED Green (Usage: status)
BJ9 - Audio Enclosure
3S1 - Reset Button
CP3 - PMOD 3.3V I2C Bus
4J25 - Power Jack J25, 2.1mm (optional 12V power input)
DJ17 - I2C (for optional module PLL access)
5S5 - DIP Switch for Boot Mode and FMCVADJ
EJ6/15 - Firefly - GTH 
6J10 - Enclosure Pin header(Reset and Power Button, HD LED (Usage: status/user) and Power LED (Usage: status/user))
FJ31 - SATA
7S4 - DIP Switch for CPLD access and power control
GJ21/22 - Firefly - loopback only
8J12 - XMOD with green dot for Module JTAG and UART, XMOD LED D4 Red used  for status information
HJ11 - PCIe (1x)
9J28  - XMOD for CPLD,FMC JTAG and Firmware ID over UART(need CPLD Firmware 7 or newer) , XMOD LED D4 Red used for status information
IJ30 - PJTAG
10FPGA Done LED (location varies slightly on different module series )
JJ5 -  FMC HPC
11J20  - ATX Power Connector (Main 12V and 5V Power supply), recommended power supply connector
KJ24 - CAN
12D1 - SFP LED Red (Usage: status/user)
LJ8 - USB 3.0 (2x) Enclosure
13D8  - SFP LED Green (Usage: status/user)
MJ27 - SD
14D9  - SFP LED Red (Usage: status/user)
NJ14 - SFP (2x)
15D10  - SFP LED Green (Usage: status/user)
OJ7 - USB 3.0 (2x), ETH (1x)
16J7 - ETH LED Yellow (Usage: status)
PJ13 - Displayport (1x)
17J7 - ETH LED Green/Orange (Usage: status)
QP2 - PMOD 3.3V FPG IOs || Bottom side: J16 - microSD
18D4 - LED Green (Usage: status/user) || D5 - LED Red (Usage: status/user)


Power supply

Recommended power supply unit is PC power supply unit over connector J20 (Overview - 12)

  • DIP S4-4 can be switched OFF with this power supply configuration (CPLD firmware depended)

Optional single 12V power supply over J25 (Overview - 12)

  • DIP S4-4 must be switched ON with this power supply

DIP-Switches and Push Buttons

Overview 7DefaultDescription
S4-1OFFSoC PUDC, ON (low - internal FPGA pull ups enabled), OFF (high - internal FPGA pull ups disabled)
S4-2OFFN.C.
S4-3OFFJTAGEN  ON (CPLD access), OFF (FMC access)
S4-4ONEnable on board 5V permanently
DIP Switches S4


Overview 5DefaultDescription
S5-1ON
  • ON(1), ON(2) - Default, boot from SD/microSD or SPI Flash if no SD is detected
  • OFF(1), ON(2) - Boot from eMMC
  • ON(1), OFF(2) - Boot mode  PJTAG0
  • OFF(1), ON(2) -Boot mode main  JTAG
S5-2ON
S5-3OFFUser Input over RGPIO
S5-4OFFVADJ OFF(1.8V), ON(1.2V)
DIP Switches S5 (CPLD Firmware depended)



Jumpers

Jumpers

LEDs


Carrier LEDs

Furthermore, there are two user LEDs on module TE0728.

DesignatorColorConnected toNote
D1RedDONE signal (PS Configuration Bank 503)

This LED goes ON when power has been applied to the module and stays ON until MPSoC's programmable logic is configured properly.

Module LEDs

JTAG/UART

SoC JTAG and UART connections are available through XMOD JTAG adapter with the green dot on J12. For more information refer to TE0790.

DIP Switch on the XMOD JTAG adapter must be set like the following table.

XMOD DIP SwitchSetting
1ON
2OFF
3OFF
4OFF
XMOD JTAG DIP Switch. Attention: Never changes the default setting

CPLD Firmware Update

Boot Mode

Reference Designs

Notes

Module and Carrier are also as starter kit available:


  • No labels