You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Next »

Download PDF version of this document.

Table of Contents

Overview

The Trenz Electronic TE0802 is an evalution module.

Key Features

  • MPSoC: Xilinx Zynq XCZU2CG-1SBVA484E
  • SDRAM: LPDDR4-3733 8Gb 256Mx32 
  • Storages:
    • SPI Flash 256Mb (32M x 8) 133 MHz
    • microSD Card
    • M.2 SSD PCIe
  • Display Interfaces: 
    • DisplayPort
    • VGA
    • 4 Digit 7-Segment LED Display
    • 8 LEDs
  • Audio:
    • 3.5 mm Jack (PWM Output)
  • Input:
    • 5 User Buttons
    • 8 Bit Slide Switches
    • Reset Button
  • User I/O:
    • 2x Pmod Connector
  • Communication:
    • 1GB Ethernet RJ45
    • USB 3.0 Host (Type A Connector)
  • Debug
    • USB JTAG/UART microUSB
  • Power
    • 5 V +/- 10%
    • ~3.5 W

Block Diagram

draw.io

Diagram attachment access error: cannot display diagram

TE0802 Block Diagram

Main Components

TE0802 Main Components (Picture shows Revision 01)
  1. Xilinx Zynq UltraScale+ MPSoc, U14
  2. LPDDR4 SDRAM, U13
  3. M.2 Key M PCIe x1, U5
  4. SPI Flash Memory, U16
  5. EEPROM, U2, U18
  6. Oscillator, U15, U7, U19, U23, U43
  7. Clock Generator, U8
  8. Clock Generator Programming Connector, J14
  9. Grove Connector, J10
  10. Pmod Host Socket, J5...6
  11. Headphone Jack, J12
  12. D-Sub Connector, J7
  13. DisplayPort, J3
  14. RJ45 Socket, J4
  15. Ethernet PHY, U6
  16. USB Type A, J11
  17. USB 2.0 PHY, U22
  18. Micro USB 2.0 Type B, J8
  19. FTDI USB 2.0 to JTAG/UART Converter, U17
  20. microSD Card, J9
  21. Slide Switch, S1
  22. Push Button, BTN1...5
  23. DIP Switch, S7...8
  24. 4 Digit 7-Segment LED Display, D9
  25. 8x LEDs (Red), LED0...7
  26. Power Jack, J13
  27. Overvoltage/Undervoltage/Reverse Supply Protector, U12
  28. Power Management Integrated Circuit (PMIC), U1, U9
  29. Power Good LED (Green), D12

Initial Delivery State

Storage device name

Content

Notes

SPI Flash (U16)

Not programmed


EEPROM (U2)Not programmedExcept Ethernet MAC
EEPROM (U18)Programmed

FTDI Configuration

LPDDR4 SDRAM (U13)Not programmed
Initial Delivery State of Programmable Devices on the Module

Configuration Signals

MODE Signal State

MODE0MODE1Boot Mode

MODE[1:0]

00

JTAG

MODE[1:0]

01QSPI(24b)

MODE[1:0]

10QSPI(32)

MODE[1:0]

11SD0(2.0)
Boot process.

Signal

Connected toNote

POR_B

BTN6, Push ButtonConnected to nRESET
Reset process.

Signals, Interfaces and Pins

I/Os on Pin Headers and Connectors

FPGA bank number and number of I/O signals connected to the connectors:

FPGA BankConnector I/O Signal CountVoltage LevelNotes

J8, (Micro USB)



J9, (Micro SD Card)



J4, (RJ45)


Bank 505J11, (USB 3.0)2 Differential Pairs0.85 V

U5, (SSD M.2)


Bank 505J3, (Display Port Connector)2 Differential Pairs0.85 V
Bank 26J7, (D-Sub Host Socket)2 Single Ended3.3 V
Bank 65, 66,J7, (D-Sub Host Socket)12 Single Ended1.8 V
Bank 65J12, Headphone3 Single Ended1.8 V
Bank 500J10, (Grove Connector)2 Single Ended3.3 V
Bank 26J5 (Pmod Host Socket)8 Single Ended3.3 V
Bank 26J6 (Pmod Host Socket)8 Single Ended3.3 V
General I/O to Pin Header and Connectors Information

Micro USB 2.0 Connector

FTDI FT2232 (U17) can be accessed through micro USB 2.0 B connector (J8) for JTAG (channel A). Channel B is connected to the FPGA and can be used for UART.

Micro SD Card Connector

TEI0802 is equipped with a micro SD card connector (J9).

SchematicCorresponding SignalsConnected toNotes












Display Port Socket Information

RJ45 Connector

TEI0802 is equipped with a RJ45 connector and an Ethernet PHYs. RJ45 connectors J4 is connected to Ethernet PHYs U6.

PinSchematicETH PinNotes
































RJ45 Connector Information

USB Connector

TEI0802 is equipped with a USB connector (J11).

SchematicCorresponding SignalsConnected toNotes












USB Socket Information

SSD M.2 Connector

TEI0802 is equipped with a SSD M.2 connector (U5).

SchematicCorresponding SignalsConnected toNotes












SSD M.2 Connector Information

Display Port Connector

TEI0802 is equipped with a Display Port connector (J3).

SchematicCorresponding SignalsConnected toNotes
DP_TX_L0_P/NDP0_TX_P/NBank 505
DP_TX_L1_P/NDP1_TX_P/NBank 505
DP_TX_AUX_P/NDP_AUX_TX/RXBank 501
Display Port Socket Information

D-Sub Connector

TEI0802 is equipped with a D-Sub connector (J7).

SchematicCorresponding SignalsConnected toNotes
VGA_REDVGA_R0...3Bank 65Red Channel
VGA_GREENVGA_G0...3Bank 65Green Channel
VGA_BLUEVGA_B0...3Bank 66Blue Channel
VGA_RGB_HSYNCVGA_HSBank 26Horizontal Sync
VGA_RGB_VSYNCVGA_VSBank 26Vertical Sync
D-Sub Connector Information

Headphone Connector

TEI0802 is equipped with a headphone connector (J12).

SchematicCorresponding SignalsConnected toNotes












Headphone Connector Information

Grove Connector

TEI0802 is equipped with a grove connector (J10).

SchematicCorresponding SignalsConnected toNotes












Grove Connector Information

Pmod Host Socket

TEI0802 has 2 Pmod 2x6 host sockets which are connected to the FPGA.

DesignatorSignalsConnected to Notes
J5PMOD_A0...7Bank 26
J6PMOD_B0...7Bank 26
Pmod SMD Host Socket Information

On-board Peripherals

Chip/InterfaceDesignatorNotes
QSPI Flash MemoryU16
SDRAM MemoryU13
EEPROMU18, U2
USB PHYU22
Ethernet PHYU6
FTDI FT2232HU17
Clock GeneratorU8
OscillatorsU43, U19, U15, U7, U23
7-Segment LEDD9
User LEDs

Push Buttons

DIP SwitchS1
Switch

On board peripherals

Quad SPI Flash Memory


MIO PinSchematicU16 PinNotes
MIO0MIO0B2SPI_CLK
MIO1MIO1D2SPI_DQ1
MIO2MIO2C4SPI_DQ2
MIO3MIO3D4SPI_DQ3
MIO4MIO4D3SPI_DQ0
MIO5MIO5C2SPI_CS
Quad SPI Interface MIOs and Pins

LPDDR4 SDRAM

The TE0802 evaluation board has 1 GByte volatile LPDDR4 SDRAM IC for storing user application code and data. The details depends on the assembly option.

  • Part number:
  • Supply voltage:
  • Speed: 
  • NOR Flash
  • Temperature: 

EEPROM

MIO PinSchematicU?? PinNotes








I2C EEPROM interface MIOs and pins

MIO PinI2C AddressDesignatorNotes
MIO8...90x50U2
I2C Address for EEPROM

USB PHY

The TEI0802 is equipped with a USB PHY. 

USB PHY PinSignal Schematic NamesUSBNote
















































































USB PHY Connections and Pins

Ethernet PHY

The TEI0802 is equipped with an Ethernet PHY (U6) which is connected to RJ45 (J) connector. 

Ethernet PHY PinSignal Schematic NamesETHNote
TXD0...3
Bank
TXC
Bank
TXEN
Bank
RXD0...3
Bank
RXC/B-CAST_OFF
Bank
RXER/ISO
Bank
INTRP/nNAND_Tree
Bank
XI
Oscillator, U
MDC
Bank
MDIO
Bank
COL/CONFIG0
Bank
CRS/CONFIG1
Bank
RXDV/CONFIG2
Bank
LED0/NWAYEN

RJ45 - Green LED, J


LED1/SPEED

RJ45 - Yellow LED, J


nRST
Bank
RXM
RJ45, J
RXP
RJ45, J
TXM
RJ45, J
TXP
RJ45, J
Ethernet PHY Connections and Pins

FTDI FT2232

The FTDI chip U17 converts signals from USB 2.0 to a variety of standard serial and parallel interfaces. Refer to the FTDI data sheet for more information about the capacity of the FT2232H chip.
Channel A of FTDI FT2232H chip is used in MPPSE mode for JTAG. Channel B is used in UART mode.

The configuration of FTDI FT2232H chip is pre-programmed on the EEPROM U18.

FTDI Chip PinSignal Schematic NameConnected toNotes
ADBUS0TCKBankJTAG interface
ADBUS1TDIBank
ADBUS2TDOBank
ADBUS3TMS

Bank

BDBUS0FT_B_TXBankUART
BDBUS1FT_B_RXBankUART
EECSEECSEEPROM, U18
EECLKEECLKEEPROM, U18
EEDATAEEDATAEEPROM, U18
OSCI-12 MHz Oscillator, U19
DMD_NMicro USB 2.0, J8
DPD_PMicro USB 2.0, J8
FTDI Chip Interfaces and Pins

Clock Generator

The TEI0802 is equipped with a clock generator (U8). 

Clock Generator PinSignal Schematic Names
Note
















































































Clock Generator Connections and Pins

Oscillators

DesignatorDescriptionFrequencyNote
U43Clock for Clock Generator25 MHz
U15
33 MHz
U7
25 MHz
U23Clock for USB52 MHz
Oscillators

7-Segment Display

The TEI0802 has a 4-Digit-7-Segment LED display.

PinSchematicConnected to Notes
A/L1SEG_CA

B/L2SEG_CB

C/L3SEG_CC

DSEG_CD

ESEG_CE

FSEG_CF

GSEG_CG

DPSEG_CDP

A1SEG_AN

A2SEG_AN4

A3SEG_AN3

A4SEG_AN2

L1-L3SEG_AN1

7-Segment LED Pins


User LEDs

SchematicColorConnected toActive LevelNote
LED0...7RedBank 65High
D12GreenU9, PMICHigh
On-board LEDs

Push Buttons

SchematicDesignator Connected toFunctionalityNote
RESET
BankReset
RST_GPIO
BankReset/GPIO
USER_BTN_LEFT
BankUser Push Button
USER_BTN_UP
BankUser Push Button
USER_BTN_OK
BankUser Push Button
USER_BTN_RIGHT
BankUser Push Button
USER_BTN_DOWN
BankUser Push Button
On-board Push Buttons


DIP Switch

SchematicColorConnected toActive LevelNote










DIP Switch

Switch

SchematicColorConnected toActive LevelNote










Switch


Power and Power-On Sequence

Power Supply

Power supply with minimum current capability of 3 A for system startup is recommended.

Power Consumption

Power Input PinTypical Current
VINTBD*
Power Consumption

* TBD - To Be Determined

Power Distribution Dependencies

Power Distribution

Power-On Sequence

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Power Sequency

Power Rails

Power Rail Name

B2B Connector

JM1 Pin

B2B Connector

JM2 Pin

B2B Connector

JM3 Pin

DirectionNotes
























Module power rails.

Bank Voltages

Bank          

Schematic Name

Voltage

Notes
Bank 503+3.3V3.3 V
Bank 26+3.3V3.3 V
Bank 65+1.8V_PL1.8 V
Bank 500+3.3V3.3 V
Bank 501+3.3V3.3 V
Bank 502+1.8V_PS1.8 V


Bank 504+1.1V_LPDDR41.1 V


Bank 505

+0.85V_MGTRAVCC

+1.8V_MGTRAVTT

0.85 V

1.8 V

???
Zynq SoC bank voltages.

Technical Specifications

Absolute Maximum Ratings

SymbolsDescriptionMinMaxUnit
VINInput Supply Voltage (J13)45.5V
PS absolute maximum ratings

Recommended Operating Conditions

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

ParameterMinMaxUnitsReference Document
VIN45.5V
Recommended operating conditions.

Physical Dimensions

Module size: 100 mm × 100 mm.  Please download the assembly diagram for exact numbers.

PCB thickness: 1,48 mm

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Physical Dimension

Currently Offered Variants 

Trenz shop TE0728 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History


DateRevisionChangesDocumentation Link
-










Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Board hardware revision number.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • Initial Release

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


  • No labels