Download PDF version of this document.

Table of Contents

Overview

The Trenz Electronic TEM0005-02 is a low-cost module with Microsemi SmartFusion2 SoC and 32 MByte flash memory for configuration and operation. SmartFusion2 combines a 166 MHz Cortex-M3 MCU with 256 KByte Flash and 80 KByte SRAM as well as 12 kLUT FPGA Core Logic.

Refer to http://trenz.org/tem0005-info for the current online version of this manual and other available documentation.

Key Features

  • SoC/FPGA
    • Package: VFG400
    • Device: M2S010, M2S050 *
    • Engine: 166Mhz 32Bit ARM Cortex-M3
    • Speed: Standard
    • Temperature: C, I*
  • RAM/Storage
    • Low Power DDR3
      • Data width: 16bit
      • Size: def. 2Gb
    • SPI Flash
      • size: 256 M bit 
    • 2Kb EEPROM
  • On Board
    • Crypto Authentication IC
    • Voltage monitor IC
    • 10/100 Mbps PHY Ethernet
  • Interface
    • Samtec ST5 B2B Connector
  • Power
    • 3.3V supplied from carrier
  • Dimension
    • 56 x 31 mm
  • Notes
    • * depends on assembly version

Block Diagram


TEM0005 block diagram

Main Components

TEM0005 main components
  1. Microsemi SmartFusion2 SoC, U2
  2. Dual DCDC Regulator, U7
  3. EEPROM, U4
  4. 10/100 Mb Ethernet, U1
  5. QSPI Flash, U3
  6. Authentication IC, U6
  7. DDR3 Memory, U5
  8. B2B Connector, J1

Initial Delivery State

Storage device name

Content

Notes

Quad SPI Flash

Not Programmed


EEPROMNot Programmed


CryptoAuthenticationNot Programmed
Initial delivery state of programmable devices on the module

Configuration Signals

Signal

B2BI/ONote
RESET


J1-11
Active low reset 
Reset process.

Signals, Interfaces and Pins

Board to Board (B2B) I/Os

FPGA bank number and number of I/O signals connected to the B2B connector, J1.

FPGA BankInterfaceI/O Signal CountVoltage LevelNotes
Bank 1GPIO8x Single Ended3.3V
UART4x Single Ended3.3V
I2C2x Single Ended3.3V
GOLDEN1x Single Ended3.3V
Bank 2ULPI/I/O12x Single Ended3.3V
I2C2x Single Ended3.3V
GPIO10x Single Ended 3.3V
SC SPI4x Single Ended3.3V
SPI17x Single Ended3.3V
Bank 3JTAG5x Single Ended3.3V
Reset 1x Single Ended3.3V
Bank 4I/O24x Single Ended/12 LVDS pairs3.3V
Bank 6I/O28x Single Ended/14 LVDS pairsVDDI6max 2.5V
Bank 7I/O4x Single Ended3.3V
General PL I/O to B2B connectors information


JTAG Interface

JTAG access to the TEM0005 SoM through B2B connector J1.

JTAG Signal

B2B Connector

TMSJ1-14
TDIJ1-8
TDOJ1-10
TCK

J1-12

TRSTJ1-7
JTAG pins connection

Test Points

Test PointSignalConnected toNotes
TP1CLKOUTRegulator, U7
Test Points Information

On-board Peripherals

Chip/InterfaceDesignatorNotes
QSPIU3
DDR3L SDRAMU5
EEPROMU4
Authentication ICU6
Ethernet PHYU1
OscillatorsY3
On board peripherals

(Quad) SPI Flash Memory

The TEM0005 is equipped with a (Q)SPI flash memory, U3 provided in order to store data and configuration. 

SchematicU3 PinConnected toNotes
SPI0_SS0nCEFPGA Bank 2
SPI0_CLKSCKFPGA Bank 2
SPI0_SDOSI/IO0FPGA Bank 2
SPI0_SDISO/IO0FPGA Bank 2
Quad SPI interface MIOs and pins

EEPROM

The TEM0005 is equipped with an EEPROM IC, U4. The I2C signals are connected to authentication IC as well.

SchematicU4 PinNotes
I2C0_SCLSCL
I2C0_SDASDA
I2C EEPROM interface MIOs and pins

 PinI2C AddressDesignatorNotes
SCL/SDA0x70U4
I2C address for EEPROM

Authentication IC

There is an Authentication IC ATECC608A provided on TEM0005, The IC is connected to I2C0 bus.

 PinSchematicNotes
SCLI2C0_SCLSerial Clock
SDAI2C1_SCLSerial Data
Authentication IC information

 PinI2C AddressDesignatorNotes
SCL/SDA0xC0U6This is the default value, which can be changed, see device datasheet.
I2C address for Authentication IC

DDR3L SDRAM

The TEM0005 SoM has 2 Gb volatile DDR3L SDRAM IC for storing user application code and data.

  • Part number: IS43TR16128CL-125KBLI
  • Supply voltage: 1.5 V
  • Temperature: -40 to 95 °C

Ethernet Transceiver

On board 10/100 Mbps Ethernet Transceiver U1 is provided on the module TEM0005. 

U1 Pin Signal NameConnected toNote
RXM/RXPETH1_RXB2B, J1
TXM/TXPETH1_TXB2B, J1
LED0/NWAYENETH1_LED0B2B, J1
LED1/SPEEDETH1_LED1B2B, J1
MDIOETH1_MDIOFPGA Bank 7, U2
MDCETH1_MDCFPGA Bank 7, U2
REXT-GND
INTRPETH1_INTRPFPGA Bank 7, U2
XO/XI-Crystal Oscillator, Y3
nRSTETH1_RSTFPGA Bank 7, U2
CONFIG0...2ETH1_COL/CRC/RXDVFPGA Bank 7, U2
TXCETH1_TXCFPGA Bank 7, U2
TXENETH1_TXENFPGA Bank 7, U2
TXD0...3ETH1_TXD0...3FPGA Bank 7, U2
RXD0...3ETH1_RXD0...3FPGA Bank 7, U2
RXCETH1_RXCFPGA Bank 7, U2
RXCERETH1_RXCERFPGA Bank 7, U2
Ethernet PHY to Zynq SoC connections


Clock Sources

DesignatorDescriptionFrequencyNote
Y3Crystal Oscillator25 MHzConnected to ETH PHY
Osillators


Power and Power-On Sequence

Power Supply

Power supply with minimum current capability of 1.5 A for system startup is recommended.

Power Consumption

Power Input PinTypical Current
VINTBD*
Power Consumption

* TBD - To Be Determined

Power Distribution Dependencies

Power Distribution

Power-On Sequence

Power Sequency

Voltage Monitor Circuit

The TEM0005 is equipped with a voltage monitoring IC, U8. Reset Logic Output (nRST) asserts low when any of the V1, V2, or ADJ inputs are below their reset thresholds. 

Voltage Monitor Circuit

Power Rails

Power Rail Name

B2B Connector J1 Pin

DirectionNotes
3.3V1, 2, 3, 4Input
VDDI622Input
Module power rails.

Bank Voltages

Bank          

Schematic Name

Voltage

Notes
Bank01.5V1.5V
Bank13.3V3.3V
Bank23.3V3.3V
Bank33.3V3.3V
Bank43.3V3.3V
Bank53.3V3.3V


Bank6VDDI6max. 2.5V

supplied by carrier

Bank73.3V3.3V
Zynq SoC bank voltages.


Board to Board Connectors

Unable to render {include} The included page could not be found.

Technical Specifications

Absolute Maximum Ratings

SymbolsDescriptionMinMaxUnit
VINInput Supply Voltage-0.33.63V
STG_TStorage Temperature-45125°C
PS absolute maximum ratings

Recommended Operating Conditions

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

ParameterMinMaxUnitsReference Document
VIN3.153.45VSee the carrier datasheets.
OPT_T0 /-4085°CSee Microsemi Smartfusion2 datasheet. Depends on assembly version.
Recommended operating conditions.

Physical Dimensions

  • Module size: 56 mm × 31 mm.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 4 mm.

PCB thickness:  1.6 mm.

Physical Dimension

Currently Offered Variants 

Trenz shop TEM0005 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History


DateRevisionChangesDocumentation Link
2019-10-01REV01
  • Initial Release
REV01
2020-05-20REV02
  • Support M2S050 ->added R29,R30, C24..C26,C31
  • Added resistor R32
  • Full upd LIB
REV02
Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Board hardware revision number.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • initial Release

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


  • No labels