Versions Compared

Old Version 12

changes.mady.by.user John Hartfiel

Saved on

compared with

New Version 13

changes.mady.by.user John Hartfiel

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  1. _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell:
  2. Press 0 and enter to start "Module Selection Guide"
  3. (optional Win OS) Generate Virtual Drive or use short directory  for the reference design (for example x:\<design name>)
  4. Create Project (follow instruction of the product selection guide), settings file will be configured automatically during this process)
    1. (optional for manual changes) Select correct device and Xilinx install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"
      Note: Select correct one, see alsoTE Board Part Files
  5. Create XSA and export to prebuilt folder
    1. Run on Vivado TCL: TE::hw_build_design -export_prebuilt
      Note: Script generate design and export files into \prebuilt\hardware\<short dir>. Use GUI is the same, except file export to prebuilt folder
  6. Generate Programming Files with Vitis
    1. Run on Vivado TCL: TE::sw_run_vitis -all
      Note: Scripts generate applications and bootable files, which are defined in "sw_lib\apps_list.csv"
      App from Firmware folder will be add into BlockRAM. If you add other app, you must select *.elf manually on Vivado
    2. (alternative) Start SDK with Vivado GUI or start with TE Scripts on Vivado TCL: TE::sw_run_vitis
      Note:  TCL scripts generate also platform project, this must be done manuelly in case GUI is used. See Vitis
  7. Copy Application (hello_te0711te0725.elf) into \firmware\microblaze_0\
  8. Regenerate Design:
    1. Run on Vivado TCL: TE::hw_build_design -export_prebuilt
      Note: App from Firmware folder will be add into BlockRAM. If you add other app, you must select *.elf manually on Vivado
    2. (alternative) Use SDK or Vivado to update generate Bitfile with new Application and regenerate mcs manually.

...

Page properties
hiddentrue
idComments

----------------------------------------------------------

FPGA Example

scu

MCS Firmware to configure SI5338 and Reset System.

srec_spi_bootloader

TE modified 2019.2 SREC

Bootloader to load app or second bootloader from flash into DDR

Descriptions:

  • Modified Files: blconfig.h, bootloader.c
  • Changes:
    • Add some console outputs and changed bootloader read address.
    • Add bugfix for 2018.2 qspi flash

xilisf_v5_11

TE modified 2019.2 xilisf_v5_11

  • Changed default Flash type to 5.

----------------------------------------------------------

Zynq Example:

zynq_fsbl

TE modified 2019.2 FSBL

General:

  • Modified Files:main.c, fsbl_hooks.h/.c (search for 'TE Mod' on source code)

  • Add Files: te_fsbl_hooks.h/.c(for hooks and board)\n\

  • General Changes: 
    • Display FSBL Banner and Device ID

Module Specific:

  • Add Files: all TE Files start with te_*
    • READ MAC from EEPROM and make Address accessible by UBOOT (need copy defines on uboot  platform-top.h)
    • CPLD access
    • Read CPLD Firmware and SoC Type
    • Configure Marvell PHY

zynq_fsbl_flash

TE modified 2019.2 FSBL

General:

  • Modified Files: main.c
  • General Changes:
    •  Display FSBL Banner
    • Set FSBL Boot Mode to JTAG
    • Disable Memory initialisation

ZynqMP Example:

----------------------------------------------------------

zynqmp_fsbl

TE modified 2019.2 FSBL

General:

  • Modified Files: xfsbl_main.c, xfsbl_hooks.h/.c, xfsbl_board.h/.c(search for 'TE Mod' on source code)
  • Add Files:  te_xfsbl_hooks.h/.c (for hooks and board)\n\
  • General Changes: 
    • Display FSBL Banner and Device Name

Module Specific:

  • Add Files: all TE Files start with te_*
    • Si5338 Configuration
    • ETH+OTG Reset over MIO

zynqmp_fsbl_flash

TE modified 2019.2 FSBL

General:

  • Modified Files: xfsbl_initialisation.c, xfsbl_hw.h, xfsbl_handoff.c, xfsbl_main.c
  • General Changes:
    •  Display FSBL Banner
    • Set FSBL Boot Mode to JTAG
    • Disable Memory initialisation


zynqmp_pmufw

Xilinx default PMU firmware.

----------------------------------------------------------

General Example:

hello_te0820

Hello TE0820 is a Xilinx Hello World example as endless loop instead of one console output.

u-boot

U-Boot.elf is generated with PetaLinux. Vitis  is used to generate Boot.bin.

Template location: ./sw_lib/sw_apps/

hello_te0725

Hello TE0725 is a Xilinx Hello World example as endless loop instead of one console output.

...

Scroll Title
anchorTable_dch
titleDocument change history.

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths2*,*,3*,4*
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

DateDocument Revision

Authors

Description

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd

Page info
current-version
current-version
prefixv.



Page info
modified-user
modified-user

  • typo
2020-04-20v.12John Hartfiel
  • 2019.2 update
  • Docu Style Documentation style update
2018-08-09v.9John Hartfiel
  • 2018.2 update

2018.06.05

v.8John Hartfiel
  • Board Part Documentation update
  • Typo correction UART Speed
2018-03-16

v.5

John Hartfiel
  • 2017.4 release
2018-03-12v.1

Page info
created-user
created-user

  • Initial release

All

Page info
modified-users
modified-users



...