Page History
Scroll Ignore |
---|
Download PDF Version of this Document. |
Scroll pdf ignore | ||||
---|---|---|---|---|
Table of Contents
|
Overview
Scroll Only (inline) |
---|
Online version of this manual and other related documents can be found at https://wikishop.trenz-electronic.de/de/display/PD/ Download/?path=Trenz_Electronic/TE0712 |
The Trenz Electronic ... TE0712 is an industrial-grade ... based on ...
Block diagram
Put you block diagram here...
Main components
Put top and bottom pics with labels of the real PCB here...
Add description list of PCB labels here...
Key features
List key features here, like FPGA type, amount and type of RAM, type of flash, etc.
...
Additional assembly options are available for cost or performance optimization upon request.
Initial Delivery State
Storage device name | Content | Notes |
---|---|---|
|
|
Signals, Interfaces and Pins
Board to Board (B2B) I/O's
I/O signals connected to the SoC's I/O bank and B2B connector:
...
For detailed information about the pin out, please refer to the Pinout Tables.
Default MIO Mapping
MIO | Function | B2B Pin | Notes | MIO | Function | B2B Pin | Notes | |
---|---|---|---|---|---|---|---|---|
Gigabit Ethernet
On board Gigabit Ethernet PHY is provided with ...
Ethernet PHY connection
PHY Pin | PS | PL | Notes |
---|---|---|---|
USB Interface
USB PHY is provided with ...
...
The schematics for the USB connector and required components is different depending on the USB usage. USB standard A or B connectors can be used for Host or Device modes. A Mini USB connector can be used for USB Device mode. A USB Micro connector can be used for Device mode, OTG Mode or Host Mode.
I2C Interface
On-board I2C devices are connected to MIO.. and MIO.. which are configured as I2C... by default. I2C addresses for on-board devices are listed in the table below:
I2C Device | I2C Adress | Notes |
---|---|---|
JTAG Interface
JTAG access to the ... is provided through B2B connector ....
...
Note |
---|
JTAGEN pin in B2B connector ... should be kept low or grounded for normal operation. |
System Controller I/O Pins
Special purpose pins are connected to smaller System Controller CPLD and have following default configuration:
Pin Name | Mode | Function | Default Configuration |
---|---|---|---|
PGOOD | Output | Power Good | Active high when all on-module power supplies are working properly. |
JTAGEN | Input | JTAG Select | Low for normal operation. |
Boot Modes
By default the ... supports QSPI and SD Card boot modes which is controlled by the MODE input signal from the B2B connector.
MODE Signal State | Boot Mode |
---|---|
high or open | SD Card |
low or ground | QSPI |
LED's
LED | Color | Connected to | Description and Notes |
---|---|---|---|
Onboard Peripherals
Processing System (PS) Peripherals
Name | IC | ID | PS7 | MIO | Notes |
---|---|---|---|---|---|
SPI Flash | S25FL256SAGBHI20 | U14 | QSPI0 | MIO1..MIO6 |
Clocking
Clock | Frequency | IC | FPGA | Notes |
---|---|---|---|---|
PS CLK | 33.3333 Mhz |
| PS_CLK | PS subsystem main clock. |
GT REFCLK1 | 125 Mhz |
| Default clock is 125 MHz. |
RTC - Real Time Clock
An temperature compensated ... is used for Real Time Clock ...
PLL - Phase-Locked Loop
There is a I2C programmable clock generator ... chip on the ...
...
I/O | Default Frequency | Notes |
---|---|---|
MAC-Address EEPROM
A ... EEPROM (U..) is used which contains a globally unique 48-bit node address, that is compatible with EUI-48(TM) and EUI-64(TM) specification.
Power and Power-On Sequece
Power Supply
Power supply with minimum current capability of ...A for system startup is recommended.
...
* TBD - To Be Determined soon with reference design setup.
Power-On Sequence
For highest efficiency of on board DC/DC regulators, it is recommended ...
Power Rails
Voltages on B2B- Connectors | B2B | B2B | B2B | Input/ Output | Note |
---|---|---|---|---|---|
Bank Voltages
Bank | Schematic Name | Voltage | TE0715-xx-15 | TE0715-xx-30 |
---|---|---|---|---|
Board to Board Connectors
... put some B2B related information here if you have them ...
Please take care, B2B connectors are of interest when on module. B2B on baseboard has no meaning for the user of the baseboard.
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN supply voltage | V | - | ||
Storage temperature | -40 | +85 | °C | - |
Recommended Operating Conditions
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN supply voltage |
Note |
---|
Assembly variants for higher storage temperature range are available on request. |
Physical Dimensions
Module size: ... mm × ... mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: ... mm.
PCB thickness: ... mm.
Highest part on PCB: approx. ... mm. Please download the step model for exact numbers.
...
Put mechanical drawings here...
Operating Temperature Ranges
Commercial grade: 0°C to +70°C.
...
Operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Weight
... g - Plain ...
... g - Set of bolts and nuts
Revision History
Hardware Revision History
Date | Revision | Notes | PCN | Documentation link |
---|---|---|---|---|
- | 01 | Prototypes |
...
Put pic of PCB silk screen here showing model and revision ...
Document Change History
Date | Revision | Contributors | Description |
---|---|---|---|
2016-11-30 | Jan Kumann
| Initial Document |
Disclaimer
Include Page | ||||
---|---|---|---|---|
|