Table of Contents
Overview
The Trenz Electronic TE0712 is an industrial-grade ... based on ...
Block diagram
Put you block diagram here...
Main components
Put top and bottom pics with labels of the real PCB here...
Add description list of PCB labels here...
Key features
List key features here, like FPGA type, amount and type of RAM, type of flash, etc.
Additional assembly options are available for cost or performance optimization upon request.
Initial Delivery State
Storage device name | Content | Notes |
---|---|---|
|
|
Signals, Interfaces and Pins
Board to Board (B2B) I/O's
I/O signals connected to the SoC's I/O bank and B2B connector:
Bank | Type | B2B Connector | I/O Signal Count | Voltage | Notes |
---|---|---|---|---|---|
For detailed information about the pin out, please refer to the Pinout Tables.
Default MIO Mapping
MIO | Function | B2B Pin | Notes | MIO | Function | B2B Pin | Notes | |
---|---|---|---|---|---|---|---|---|
Gigabit Ethernet
On board Gigabit Ethernet PHY is provided with ...
Ethernet PHY connection
PHY Pin | PS | PL | Notes |
---|---|---|---|
USB Interface
USB PHY is provided with ...
PHY Pin | Pin | B2B Name | Notes |
---|---|---|---|
The schematics for the USB connector and required components is different depending on the USB usage. USB standard A or B connectors can be used for Host or Device modes. A Mini USB connector can be used for USB Device mode. A USB Micro connector can be used for Device mode, OTG Mode or Host Mode.
I2C Interface
On-board I2C devices are connected to MIO.. and MIO.. which are configured as I2C... by default. I2C addresses for on-board devices are listed in the table below:
I2C Device | I2C Adress | Notes |
---|---|---|
JTAG Interface
JTAG access to the ... is provided through B2B connector ....
JTAG Signal | B2B Connector Pin |
---|---|
TCK | |
TDI | |
TDO | |
TMS |
System Controller I/O Pins
Special purpose pins are connected to smaller System Controller CPLD and have following default configuration:
Pin Name | Mode | Function | Default Configuration |
---|---|---|---|
PGOOD | Output | Power Good | Active high when all on-module power supplies are working properly. |
JTAGEN | Input | JTAG Select | Low for normal operation. |
Boot Modes
By default the ... supports QSPI and SD Card boot modes which is controlled by the MODE input signal from the B2B connector.
MODE Signal State | Boot Mode |
---|---|
high or open | SD Card |
low or ground | QSPI |
LED's
LED | Color | Connected to | Description and Notes |
---|---|---|---|
Onboard Peripherals
Processing System (PS) Peripherals
Name | IC | ID | PS7 | MIO | Notes |
---|---|---|---|---|---|
SPI Flash | S25FL256SAGBHI20 | U14 | QSPI0 | MIO1..MIO6 |
Clocking
Clock | Frequency | IC | FPGA | Notes |
---|---|---|---|---|
PS CLK | 33.3333 Mhz |
| PS_CLK | PS subsystem main clock. |
GT REFCLK1 | 125 Mhz |
| Default clock is 125 MHz. |
RTC - Real Time Clock
An temperature compensated ... is used for Real Time Clock ...
PLL - Phase-Locked Loop
There is a I2C programmable clock generator ... chip on the ...
PLL connection
I/O | Default Frequency | Notes |
---|---|---|
MAC-Address EEPROM
A ... EEPROM (U..) is used which contains a globally unique 48-bit node address, that is compatible with EUI-48(TM) and EUI-64(TM) specification.
Power and Power-On Sequece
Power Supply
Power supply with minimum current capability of ...A for system startup is recommended.
Power Consumption
Power Input Pin | Max Current |
---|---|
VIN | TBD* |
3.3VIN | TBD* |
* TBD - To Be Determined soon with reference design setup.
Power-On Sequence
For highest efficiency of on board DC/DC regulators, it is recommended ...
Power Rails
Voltages on B2B- Connectors | B2B | B2B | B2B | Input/ Output | Note |
---|---|---|---|---|---|
Bank Voltages
Bank | Schematic Name | Voltage | TE0715-xx-15 | TE0715-xx-30 |
---|---|---|---|---|
Board to Board Connectors
... put some B2B related information here if you have them ...
Please take care, B2B connectors are of interest when on module. B2B on baseboard has no meaning for the user of the baseboard.
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN supply voltage | V | - | ||
Storage temperature | -40 | +85 | °C | - |
Recommended Operating Conditions
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN supply voltage |
Physical Dimensions
Module size: ... mm × ... mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: ... mm.
PCB thickness: ... mm.
Highest part on PCB: approx. ... mm. Please download the step model for exact numbers.
All dimensions are given in mm.
Put mechanical drawings here...
Operating Temperature Ranges
Commercial grade: 0°C to +70°C.
Industrial grade: -40°C to +85°C.
Operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Weight
... g - Plain ...
... g - Set of bolts and nuts
Revision History
Hardware Revision History
Date | Revision | Notes | PCN | Documentation link |
---|---|---|---|---|
- | 01 | Prototypes |
Hardware revision number is printed on the PCB board together with the module model number separated by the dash.
Put pic of PCB silk screen here showing model and revision ...
Document Change History
Date | Revision | Contributors | Description |
---|---|---|---|
2016-11-30 | Jan Kumann
| Initial Document |
Disclaimer
Data Privacy
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
Document Warranty
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
Limitation of Liability
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
Copyright Notice
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
Technology Licenses
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
Environmental Protection
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH, RoHS and WEEE
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.