Page History

...

• Create a Plattform Designer file: File  →  New 
• Select "Qsys System File"  and press "OK"
• A new window should open.

Image Removed

• Look for "hps" inside the search field, as visible in the following figure.

Image Added

• Select "Arria V/Cyclone V Hard Processor System" via double click from the tree: Library → Processors and Peripherals → Hard Processor Systems → Arria V/Cyclone V Hard Processor System

Image Removed

• The window "Arria V/Cyclone V Hard Processor System - hps_0" should be opened as visible in the next figure.

Image Added

• In this window the HPS has to be configured with the following settings:
  • Tab FPGA Interface:
    • Uncheck "Enable MPU standby and event signals" (default)

    • AXI Bridges:

      • FPGA-to-HPS interface width: Unused
        

      • HPS-to-FPGA interface width: Unused

      • Lightweight HPS-to-FPGA interface width: Unused

  • Tab Peripheral Pins:
    • Quad SPI Flash Controller
      • → QSPI pin: HPS I/O Set 0
    • SD/MMC Controller
      • → SDIO pin: HPS I/O Set 0
      • → SDIO mode: 4-bit Data
    • UART Controllers
      • → UART0 pin: HPS I/O Set 0
      • → UART0 mode: no Flow Control
    • I2C Controllers
      • → I2C0 pin: HPS I/O Set 1
      • → I2C1 pin: HPS I/O Set 0
  • Tab HPS Clocks:
    
    • As is / Accept the default values (for both subtabs)
  • Tab SDRAM
    • Subtab Phy Settings:
      • Memory clock frequency: 333.3 MHz
      • PLL reference clock frequency: 25 MHz

    • Subtab - Memory Parameters:

      • Memory device speed grade: 800.0 MHz

      • Total interface width: 32
        

      • Row Address width: 16

      • Column Address width: 10

    • Memory Initialization Options
      

      • Memory CAS latency setting: 5

      • ODT Rtt nominal value: RZQ/6

      • Memory write CAS latency settings: 5

  • Subtab - Memory Timing:
    • tIS (base): 180 ps
    • tIH (base): 140 ps
    • tDS (base): 30 ps
    • tDH (base): 65 ps
    • tDQSQ: 100 ps
    • tQH: 0.38 cycles
    • tDQSCK: 225 ps
    • tDQSS: 0.27 cycles
    • tQSH: 0.4 cycles
    • tDSH: 0.18 cycles
    • tDSS: 0.18 cycles
    • tINIT: 500 us
    • tMRD (tMRW): 4 cycles
    • tRAS: 35.0 ns
    • tRCD: 13.75 ns
    • tRP: 13.75 ns
    • tREFI (tREFIab): 7.8 us
    • tRFC (tRFCab): 350.0 ns
    • tWR: 15.0 ns
    • tWTR: 4 cycles
    • tFAW: 40 ns
    • tRRD: 12.0 ns
    • tRTP: 12.0 n

  • Subtab - Board Settings:

    • Board Skews

      • Maximum CK delay to DIMM/device:                        0.03

      • Maximum DQS delay to DIMM/device:                     0.02

      • Minimum delay difference between CK and DQS:      0.09

      • Maximum delay difference between CK and DQS:     0.16

      • Maximum skew within DQS group:                           0.01

      • Maximum skew between DQS groups:                      0.08

      • Maximum skew within address and command bus:   0.03

• Click "Finish" to close the window "Arria V/Cyclone V Hard Processor System - hps_0".

• Add connections via clicking into the circle marked with a red rectangle in th the next figure:

  • hps_0 - h2f_reset     →          clk_0 - clk_in_reset

  • clk_0 - clk                →          hps_0 - f2h_sdram0_data

    
• The HPS is nearly configured. Apply some auto functions:
  

  • System  →  Assign Base Addresses

  • System  →  Assign Interrupt Numbers

  • System  →  Assign Custom Instruction Opcodes

  • System  →  Create Global Reset Network

• Click Generate HDL... to generate the hardware description language file.
• Window "Generation" opens.
• In this window, under "Synthesis", select via dropdown menu in which Hardware Language your HDL will be created, Verilog or VHDL,
• Uncheck Create timing and resource estimate... .
• Check Create block symbole file (.bsf).
• Click Generate, as visible in the next figure.
  

...

• Press Close.
• Leave the Plattform Designer by pressing Finish.
• A notification appears, reminding to add files into the project,
  press OK.

Close the Plattform Designer by pressing Finish.

...

After this doing this guide, following files and folders are generated with the given purpose.