...
Scroll Title |
---|
anchor | Figure_Overview |
---|
title | Board Overview |
---|
|
Scroll Ignore |
---|
scroll-pdf | true |
---|
scroll-office | true |
---|
scroll-chm | true |
---|
scroll-docbook | true |
---|
scroll-eclipsehelp | true |
---|
scroll-epub | true |
---|
scroll-html | true |
---|
| draw.io Diagram |
---|
border | truefalse |
---|
viewerToolbar | true |
---|
| |
---|
fitWindow | false |
---|
diagramDisplayName | |
---|
lbox | false |
---|
revision | 5 |
---|
diagramName | TEF1002 Overview |
---|
simpleViewer | false |
---|
width |
---|
diagramWidth | 641 |
---|
| links | auto |
---|
tbstyle | top |
---|
diagramWidth | 636 | revision | 2 |
---|
|
draw.io Diagram |
---|
border | truefalse |
---|
viewerToolbar | true |
---|
| |
---|
fitWindow | false |
---|
diagramDisplayName | |
---|
lbox | false |
---|
revision | 4 |
---|
diagramName | TEF1002_Overview_bottom |
---|
simpleViewer | false |
---|
width | |
---|
links | auto |
---|
tbstyle | top |
---|
diagramWidth | 635631 |
---|
|
|
Scroll Only |
---|
Image Modified |
|
- 4x5 module connectors
- Jumper J4 (VCCIOA)
- Jumper J7 (VCCA_SD)
- Dip swiches switches S2 and S3
- 6-pin PCI-E PCIe ATX Power Connector
- micro USB connector for FTDI USB to JTAG/UART bridge
- Push Reset push button
- Power LED
- Status LED
- top load microSD card cage
Power supply
...
Single 12V power supply with minimum current capability of 3A is recommended to power on the board via the 6-pin PCI-E PCIe ATX connector.
DIP-Switches and Push Buttons
...
Select dip switch settings according to the attached 4x5 module and your needs. Compare Dip switch setting with TRM of your module and table in TRM of TEF1002. Following a general configuration is shown.
Scroll Title |
---|
anchor | Table_DIP_PB |
---|
title | DIP Switches /Push Buttons |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Dip | Setting | Note |
---|
S1 |
| Push button configured by CPLD as reset | S2-1 | OFF | OFF, OFF, OFF selects FMC _VADJ OFF. The choice OFF, ON, OFF selects 1.8V FMC_VADJ, which is a valid bank power for TE0720.
| S2-2 | OFFON | S2-3 | OFF | S2-4 | ONOFF | Selects 4x5 module SOC/FPGA JTAG | S2-5 | ONOFF | S2-6 | OFF | S2-7 | ON | Module power enable. | S2-8 | ONOFF | Use extended Extended power sequenzing (if implemented). | S3-1 | OFF/ON | For Zynq modules: Primary Boot Mode SD/QSPI. OFF corresponds to boot from SD card. | S3-2 | OFF | ON for TE0720 (overide Overide automatic enable FMC_VADJ). For TE0720 bank bank . (1)(2) |
|
(1) Set to ON for TE0720 because bank 34 has to be
...
powered to start up. Therefore FMC VADJ has to be set to a valid value e.g. 1.8V (See S2-1 to S2-3).
(2) For TE0820 set to on to use CLK0 (VCCO 65). Therefore FMC VADJ has to be set to a valid value e.g. 1.
...
8V (See S2-1 to S2-3).
Jumpers
Page properties |
---|
|
Explain all Jumpers functionality and connection. |
For Jumper J7 compare TRM of actually used 4x5 module. The voltage of the bank where the SDIO signals are connected reside has to selected. J4 selects the module bank voltage VCCIOA. It has to be selected in accordance with IO voltage of signals connected to FFA and FFB. If both FFA and FFB are not used any setting is ok. Do not leave open (communication of 4x5 module with TEF1002 CPLD is only possible with availabe VCCIOA)!
Scroll Title |
---|
anchor | Table_Jumpers |
---|
title | Jumpers |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Jumper | Power Rail | 3.3V | 1.8V | Remark |
---|
J7 | VCCA_SD | 1-2 | 2-3 | Powers SDIO Levelshifter on 4x5 module side. | J4 | VCCIOA | 1-2 | 2-3 | Powers 4x5 bank, where FFA and FFB high speed signals are connected. |
|
LEDs
Page properties |
---|
|
Explain all user LEDs functionality and connections. |
There are four LEDs on the board. Two of them are user LEDS not further described here. Compare corresponding table in TEF1002 TRM.
Scroll Title |
---|
anchor | Table_LED |
---|
title | Carrier LEDs |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | |
---|
widths | |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
LED | Connected to | Function | Notes |
---|
D3 | 3V3IN | Power | ON when 3.3V generated from 12V input is up | D4 | SC CPLD U11, Pin C2 | Status | SC CPLD firmware dependent, for further description see firmware description. |
|
JTAG/UART
Page properties |
---|
|
Explain JTAG or UART connection breifly. |
JTAG (first FTDI port) and UART (second FTDI port) is over available via MicroUSB connector available. External JTAG Programmer is not needed.
...
Page properties |
---|
|
In this Section you must refer to the Reference Design (Test board) for the particular module. For Example: TE0728 Reference Designs |
- Use e.g. the Test board Reference Design of the installed 4x5 module.
- For TE0820 on this carrier TE0820 TD TEF1002, including PCIe endpoint and SATA, is available.
Notes
Page properties |
---|
|
In this Section you must refer to the Resources Page for the particular module. For Example: TE0728 Resources |