Versions Compared

Old Version 16

changes.mady.by.user John Hartfiel

Saved on

compared with

New Version 17

changes.mady.by.user John Hartfiel

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Scroll pdf ignore

Table of contents

Table of Contents
outlinetrue

Overview

Feature Summary

  • Power Management
  • Reset Management
  • Boot Mode Controller
  • FPGA UART routing
  • RGPIO Interface to FPGA

Firmware Revision and supported PCB Revision

...

NameDirectionPinDescription
ACBUS4          in96FTDI / currently_not_used
ACBUS5          in88FTDI / currently_not_used
ADBUS4          out98FTDI  / get M_TCK
ADBUS7          out97FTDI / currently_not_used
BDBUS0          inout87FTDI / Module UART0.RX << FTDI
BDBUS1          inout86FTDI  /Module UART0.TX >> FTDI
C_TCKout81JTAG FTDI
C_TDIout84JTAG FTDI
C_TDOin83JTAG FTDI
C_TMSout85JTAG FTDI
CM0in67DIP Switch S3-M1
CM1in66DIP Switch S3-M2
EN_FMC          out35VADJ Power on
EN1             out53Power Enable Pin for Module CPLD
JTAGEN--82Enable JTAG access to carrier CPLD for Firmware update (zero: JTAG routed to module, one: CPLD access)
Set DIP Switch S3-JTAGEN to ON, for module access.
JTAGMODEout58Enable JTAG access to to module CPLD for Firmware update on module CPLD (zero: JTAG routed to module FPGA, one: Module CPLD access)
M_TCK           in91JTAG Module
M_TDI           in94JTAG Module
M_TDO           out95JTAG Module
M_TMS           in90JTAG Module
MIO10           inout32  MIO / used by RGPIO Bus
MIO11           inout31MIO / used by RGPIO Bus
MIO12           inout39 MIO / used by RGPIO Bus
MIO13           inout34 MIO / used by RGPIO Bus
MIO14           inout40MIO / Module UART0.RX << BDBUS0
MIO15           inout30MIO / Module  UART0.TX >> BDBUS1
MODE            out28Boot Mode for Zynq Devices (Flash or SD)
NOSEQ           inout29/ currently_not_used
PGOOD           inout27/ currently_not_used
PHY_LED1        out45LED Ethernet
PHY_LED1_A      out49LED Ethernet / currently_not_used
PHY_LED2        out47LED Ethernet
PHY_LED2_A      out48LED  Ethernet / currently_not_used
POK_FMC          36LED  Ethernet / currently_not_used
RESIN           out54Module Reset
S1              in75User Button / used by RGPIO Bus
S2              in74User Button / Global Reset
SD_DETECT       in42SD Detection / used for FPGA Boot Mode
SD_WP           in43SD / RGPIO Bus
ULED1           out78LED D6
ULED2           out77LED D7
ULED3           out76LED D8
ULED4           out65LED D9
ULED5           out71LED D4
ULED6           out70LED D15
ULED7           out69LED D14
ULED8           out68LED D5
USB_OC          in99 USB Over Current
USR0in64DIP Switch S4-1 / used by RGPIO Bus (PCB REV04 only)
USR1in61DIP Switch S4-2 / used by RGPIO Bus (PCB REV04 only)
USR2in60DIP Switch S4-3 / used by RGPIO Bus (PCB REV04 only)
USR3in59DIP Switch S4-4 / used by RGPIO Bus (PCB REV04 only)
VID0            out37VADJ Voltage selection (EN5335QI)
VID1            out38VADJ Voltage selection (EN5335QI)
VID2            out41VADJ Voltage selection (EN5335QI)
X6              in19RGPIO Bus
Y0               15/ currently_not_used
Y1               14/ currently_not_used
Y2              in13RGPIO CLK
Y3              out10RGPIO TX
Y4              in9RGPIO RX
Y5               8/ currently_not_used
Y6              in7RGPIO Bus

...

Reset

RESIN (negative Reset) to module, can be set by S2 Buttonbutton.

BootmodeBoot mode

Boot Mode mode is set to SD-Boot, when SD-Card is detected.

RGPIO

RGPIO Master is a 32Bit Remote GPIO Interface to talk with FPGA over 3 lanes.

...

RGPIO Pin from FPGAValue
0-7LED 1-7
08-23unused
24-27reserved
28-31Interface detection

LED

LEDDescription
ULED1not external reset / RGPIO(0), when FPGA Interface is detected
ULED2(M1=off,M2=off) / RGPIO(1), when FPGA Interface is detected
ULED3Module UART0.RX / RGPIO(2), when FPGA Interface is detected
ULED4Module UART0.TX / RGPIO(3), when FPGA Interface is detected
ULED5SD_DETECT / RGPIO(4), when FPGA Interface is detected
ULED6(M1=on,M2=off) / RGPIO(5), when FPGA Interface is detected
ULED7X6 / RGPIO(6), when FPGA Interface is detected
ULED8Y6 / RGPIO(7), when FPGA Interface is detected

 

UART

ToFromDescription
MIO14BDBUS0Module UART0.RX
BDBUS1MIO15Module UART0.TX

 

Appx. A: Change History and Legal Notices

Revision Changes

REV01 to REV02

  • Power Management
    • VADJ is switchable by S3 dip switches
  • Reset Management
    • only little changes
  • RGPIO Interface to FPGA
    • RGPIO support
  • LED
    • new Order and accessible by RGPIO
  • Module CPLD access is possible know

Document Change History

To get content of older revision  got to "Change History"  of this page and select older document revision number.

DateDocument RevisionCPLD Firmware RevisionSupported PCB RevisionAuthorsDescription
2016-04-11

 

 REV02REV03, REV04

John Hartfiel

Work in progress
2016-04-11

 

v.1

--- 

John Hartfiel

Initial release
 All  
 

...