Versions Compared

Old Version 50

changes.mady.by.user Ali Naseri

Saved on

compared with

New Version Current

changes.mady.by.user Ali Naseri

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

HTML
<!--
Download Link: Go to Base Folder of the Module or Carrier, for example : https://shop.trenz-electronic.de/en/Download/?path=Trenz_Electronic/TE0712
Use english URL "../en/..
 -->
Scroll Ignore

Download PDF version of this document.

Scroll pdf ignore

Table of Contents

Table of Contents

...

Scroll Only (inline)
Refer to https://wiki.trenz-electronic.de/display/PD/TEBB0714+TRM for the current online version of this manual and other available documentation.

The Trenz Electronic TEBB0714 is a Carrier Board for testing, evaluation and development purposes, especially for the Multi Gigabit Transceiver units of the TE0714 module. Although this base-board is dedicated to the TE0714 module, it is also compatible with other Trenz Electronic 4 x 3 cm SoMs. See page "4 x 3 cm carriers" to get information about the SoMs supported by the TEBB0714 Carrier Board.

This base-board provides also solder pads as place-holders through hole pads for pin headers as option to get access to the PL I/O-bank pins and further interfaces of the mounted TE 4 x 3 SoM.

...

  1. 6-pin header J26 for selecting PL-bank I/O voltage
  2. 6-pin header J27 for selecting XMOD/JTAG VCCIO
  3. Samtec Razor Beam™ LSHM-150 B2B connector, JM1
  4. Samtec Razor Beam™ LSHM-150 B2B connector, JM2
  5. XMOD header, JX1
  6. Ultra small SMT coaxial connector, J5
  7. Ultra small SMT coaxial connector, J6
  8. Ultra small SMT coaxial connector, J7
  9. Ultra small SMT coaxial connector, J8
  10. User LED D1 (green)
  11. User LED D2 (red)
  12. LED D3 (red) indicating FPGA's 'Programming DONE'-signal
  13. SFP+ Connector, J1
  14. 10-pin header solder pads J4 for access to SoM's PL I/O-banks (LVDS pairs possible)
  15. 16-pin header solder pads J3, JTAG/UART header ('XMOD FTDI JTAG Adapter'-compatible pin-assignment)with ADC and MGT clock input
  16. 50-pin header solder pads J20 for access to SoM's PL I/O-banks (LVDS pairs possible)
  17. 50-pin header solder pads J17 for access to SoM's PL I/O-banks (LVDS pairs possible)

...

Pin Schematic NameXMOD Header JX1 PinB2BNote
TCKC (pin 4)JM1-90-
TDOD (pin 8)JM1-88-
TDIF (pin 10)JM1-86-
TMSH (pin 12)JM1-92-
B14_L25A (pin 3)JM2-97UART -TX (transmit line(output from module to XMOD Programmer)
B14_L0B (pin 7)JM2-99UART -RX (receive line(input to module from XMOD Programmer)
BOOTMODEE (pin 9)JM2-100-
PROG_BG (pin 11)JM1-94-

...

V_CFG Value

Jumper J27 SettingNote
1.8Vpins 1-2 connectedModule's output voltage.
V_CFG0*pins 3-4 connectedInternal module VCCIO: 3.3V or 1.8V (Settable by 0-Ohm-Resistor on TE0714 module).
3.3V_OUTpins 5-6 connectedModule's output voltage.

*Default setting, do not changed, if V_CFG0 Bank power is sourced by module itself.

Table 8: Setting of reference I/O-voltage XMOD header.


Note

Use Xilinx compatible TE0790 adapter board (designation TE-0790-xx with out 'L') to program the Xilinx Zynq devices.

The TE0790 adapter board's CPLD have to be configured with the Standard variant of the firmware. Refer to the TE0790 Resources Site for further information and firmware download.

...

As alternative to the XMOD header JX1, on the Carrier Board pin header J3 is present , which has a XMOD header-compatible pin-assignment, but also 4 with 4 additional pins as differential pairs to supply the mounted SoM with an external MGT reference clock signal and as to provide differential analog signal input:

Pin Schematic NameHeader J3 PinB2BNote
TCK4JM1-90-
TDO8JM1-88-
TDI10JM1-86-
TMS12JM1-92-
B14_L253JM2-97UART -TX (transmit line(output from module)
B14_L07JM2-99UART -RX (receive line(input to module)
BOOTMODE9JM2-100-
PROG_B11JM1-94-
XADC_P13JM1-25Analog input differential pair
XADC_N14JM1-27
CLK0_N15JM1-4AC decoupled on-board (100 nF capacitor)
CLK0_P16JM1-2

...

UART Signal Schematic NameB2BXMOD Header JX1Pin Header J3Note
B14_L0JM2-99JX1-7J3-7UART -RX (receive line(input to module)
B14_L25JM2-97JX1-3J3-3UART -TX (transmit line(output from module)

Table 10: UART interface signals.

...

The voltage direction of the power rails is from board and on-board connectors' view:

Module Connector (B2B) DesignatorVCC / VCCIODirectionPinsNotes
JM1

3.3V

Out

97, 99

3.3V module supply voltage
3.3V_OUTIn833.3V module output voltage
VCCIO34Out61PL IO-bank VCCIO
JM2

1.8V

In

18

1.8V module output voltage
3.3V_OUTOut543.3V module output voltage
V_CFG0In/out53Direction depends on solder option of the modul: Internal module VCCIO
:
3.3V or 1.8V or source from carrier is possible

Table 16: Power pin description of B2B module connector.

...

On-board Pin Header DesignatorVCC / VCCIODirectionPinsNotes
J17

3.3V

In / Out

5, 46

3.3V external supply voltage
V_CFGOut / int6, 45VCCIO, direction depends on jumper 27 settings and module solder option
J20

3.3V

In / Out

5, 46

3.3V external supply voltage
VCCIO34In / Out6, 45PL IO-bank VCCIO, depends on Jumper settings

...

Jumper / Header DesignatorVCC / VCCIODirectionPinsNotes
J26VCCIO34In1, 3, 5-
1.8VOut2-
2.5VOut4-
3.3V_OUTOut6-
J27V_CFGIn / Out1, 3, 5-direction depends on jumper 27 settings and module solder option
1.8VOut2-
V_CFG0Out4-
3.3V_OUTOut6-

...

JTAG/UART Header DesignatorVCC / VCCIODirectionPinsNotes
JX1 (XMOD)3.3VOut5Connected to 3.3V external supply voltage
VIOOut6Connected to 'V_CFG', depends on jumper 27 settings
J33.3VOut5Connected to 3.3V external supply voltage
V_CFGOut6VCCIO, direction depends on jumper 27 settings

Table 19: Power pin description of XMOD/JTAG Connector.

Board to Board Connectors

Warning

These connectors are hermaphroditic. Odd pin numbers on the module are connected to even pin numbers on the baseboard and vice versa.

4 x 3 modules use two Samtec Razor Beam LSHM connectors on the bottom side.

  • 2 x REF-189016-02 (compatible to LSHM-150-04.0-L-DV-A-S-K-TR), (100 pins, "50" per row)

Connector Mating height

When using the same type on baseboard, the mating height is 8mm. Other mating heights are possible by using connectors with a different height

...

The module can be manufactured using other connectors upon request.

Connector Speed Ratings

The LSHM connector speed rating depends on the stacking height; please see the following table:

...

6.5 GHz / 13 Gbps

...

Table 21: B2B connector speed ratings.

Current Rating

Current rating of  Samtec Razor Beam™ LSHM B2B connectors is 2.0A per pin (2 adjacent pins powered).

Connector Mechanical Ratings

  • Shock: 100G, 6 ms Sine
  • Vibration: 7.5G random, 2 hours per axis, 3 axes total

...

and module solder option

Table 19: Power pin description of XMOD/JTAG Connector.

Board to Board Connector

Include Page
IN:Module Connectors
IN:Module Connectors
Table 22: B2B connector manufacturer documentation.

Technical Specifications

Absolute Maximum Ratings

ParameterMinMaxUnitsNotes

Vin supply voltage

3.135

3.465

V

3.3V supply-voltage ± 5%

Storage Temperature

-4085

°C

WL-SMCW SMD chip LED data sheet

Table 2320: Absolute maximum ratings.

...

 ParameterMinMaxUnitsNotes
Vin supply voltage3.1353.465V-
Operating temperature-40+85°CMolex 74441-0001 Product Specification

Table 2421: Recommended operating conditions.

...

Industrial grade: -40°C to +85°C.

The TEBA0841 Carrier Board itself is capable to be operated at is operable within industrial grade temperature range.

...

DateRevision

Notes

PCNDocumentation Link
-

01

  • First Production Release
-TEBB0714-01

Table 2522: Module hardware revision history.

...

Date

Revision

Contributors

Description

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd

Ali Naseri, Jan Kumann
  • First TRM release

Table 2623: Document change history.

...