Page History
Scroll Ignore |
---|
Download PDF version of this document. |
Scroll pdf ignore | |
---|---|
Table of Contents
|
Overview
Scroll Only (inline) |
---|
Refer to https://shop.trenz-electronic.de/en/Download/?path=Trenz_Electronic/carrier_boards/TE0706 for downloadable version of this manual and additional technical documentation of the product. |
The Trenz Electronic TE0706 carrier board provides functionality for testing, evaluation and development purposes of company's 4 x 5 cm SoMs (System on Module). The Carrier board is equipped with various components and connectors for different configuration setups and needs. On-module functional components and multipurpose I/Os of the SoM's PL logic are connected via board-to-board connectors to the carrier board's components and connectors for easy user access.
See "4 x 5 cm carriers" page for more information about supported 4 x 5 cm SoMs.
Key Features
- VG96 backplane connector (mounting holes and solder pads, J6) and 50-pin IDC male connector socket (J5) to access FPGA bank's IO-pins
- SDIO port expander with voltage-level translation
- Micro SD card socket, routed to B2B-connector JB1
- USB type A connector (OTG mode), routed to B2B-connecor JB3
- 1 x user-push button S2, routed to RESIN-pin on B2B-connector JB2. By default it is configured as system reset button.
- 1 x RJ45 Gigabit Ethernet MagJack J3, PHY_MDI interface routed to B2B-connector JB1.
- 1 x Marvell Alaska 88E1512 Ethernet PHY, routed to B2B-connector JB3 and accessible via RJ45 Gigabit Ethernet MagJack J2
- Barrel jack for 5 V Power Supply input
- 4 A High-Efficiency Power SoC DC-DC Step-Down Converter (Enpirion EN6347) for 3.3 V Power Supply
- Trenz 4 x 5 Module Socket (3 x Samtec LSHM series connectors)
- JTAG/UART-pins on 12-pin header JX1, routed to B2B-connector JB2
- user configurable DIP switch S1 to set System Controller CPLD signals on SoM
- 3 x VCCIO selection jumper J10, J11 and J12 to set SoM's bank voltages
Block Diagram
Main Components
- 5V power connector jack, J1
- Reset switch, S2
- USB type A receptacle, J7
- Micro SD card socket with Card Detect, J4
- 50 pin IDC male connector, J5
- 1000Base-T Gigabit RJ45 Ethernet MagJack, J3
- 1000Base-T Gigabit RJ45 Ethernet MagJack, J2
- JTAG/UART Connector, JX1
- User DIP switch block, S1
- VCCIO voltage selection jumper block, J10 - J12
- External connector (VG96) placeholder, J6
- Samtec Razor Beam™ LSHM-150 B2B connector, JB1
- Samtec Razor Beam™ LSHM-150 B2B connector, JB2
- Samtec Razor Beam™ LSHM-130 B2B connector, JB3
Initial Delivery State
Board is shipped in following configuration:
- VCCIO voltage selection jumpers are all set to 1.8 V.
- S2 switch configured as reset button.
- One VG96 backplane connector is not soldered to the board, but is included in the package as separate component.
Different delivery configurations are available upon request.
Signals, Interfaces and Pins
Board to Board (B2B) I/Os
For detailed information about the B2B pin out, please refer to the Master Pin-out Table.
JTAG/UART Interface
JTAG access to the mounted 4 x 5 SoM is provided via 12-pin header JX1 and controlled by DIP switch S1-2 to select the device (Zynq-SoC, SC-CPLD) to program.
This header has a 'XMOD FTDI JTAG Adapter'-compatible pin-assignment, so the XMOD-FT2232H adapter-board TE0790 can be used in conjunction with the carried board to program the mounted SoM via USB interface.
JX1 pin | Configured as | B2B |
---|---|---|
C (pin 4) | TCK | JB2-100 |
D (pin 8) | TDO | JB2-98 |
F (pin 10) | TDI | JB2-96 |
H (pin 12) | TMS | JB2-94 |
A (pin 3) | MIO15 | JB1-86 (usable as UART RX/TX-line) |
B (pin 7) | MIO14 | JB1-91 (usable as UART RX/TX-line) |
Micro SD Card Socket
Micro SD Card socket is not directly wired to the B2B connector pins, but routed through a Texas Instruments TXS02612 SDIO port expander, which is needed for voltage translation due to the different voltage levels of the Micro SD Card and MIO bank 501 of the Xilinx Zynq 7000 chip. The Micro SD Card has 3.3 V signal voltage-level, but the MIO Bank 501 on the Xilinx Zynq 7000 chip is set to 1.8 V.
Ethernet
The TE0706-02 is equipped with a Marvell Alaska 88E1512 Gigabit Ethernet PHY (U6) connected to the B2B connector JB3. The I/O Voltage is fixed at 1.8V. The reference clock input of the PHY is supplied by on-board 25MHz oscillator (U7).
PHY (U6) interface connections:
PHY | B2B-pin | Notes |
---|---|---|
MDC/MDIO | JB3-49, JB3-51 | - |
LED0 | - | Connected to Ethernet jack J2 LED0 (green). |
LED1 | - | Connected to Ethernet jack J2 LED1 (green). |
INT | JB3-33 | - |
CONFIG | JB3-60 | - |
RESET | JB3-53 | - |
RGMII | JB3-37 - JB-44, JB3-47, JB3-57 - JB-59 | 12 pins. |
SGMII | - | Not connected. |
MDI | - | Connected to Gigabit-Ethernet MagJack J2. |
RJ45 Gigabit Ethernet MagJack J3
The TE0706-02 carrier board is also equipped with a second Gigabit-Ethernet MagJack J3, which is connected via MDI to the B2B connector JB1.
There is usually a corresponding Gigabit Ethernet PHY on 4 x 5 SoMs (e.g. TE0715 or TE0720), which can be used in conjunction with the baseboard MagJack J3.
USB Interface
TE0706-02 board has one physical USB type A socket J7 routed to B2B connector JB3. The corresponding USB-transceiver on 4 x 5 SoMs varies in order of the used SoM model.
There is also the option to equip a micro USB 2.0 type B receptacle socket (J8) to the board as alternative.
Info |
---|
Note: Pin OTG-ID is only assigned to USB 2.0 type B socket. |
DIP switch S1
Switch | Signal Name | ON | OFF | Notes |
---|---|---|---|---|
S1-1 | - | - | - | Not connected. |
S1-2 | PROGMODE | JTAG enabled for programing SoM's Zynq-SoC. | JTAG enabled for programing SoM's CPLD. | - |
S1-3 | MODE | Drive SoM SC CPLD pin 'MODE' low. | Leave SoM SC CPLD pin 'MODE' open. | Boot mode configuration, if supported by SoM. (Depends also on SoM's SC CPLD firmware). |
S1-4 | EN1 | Drive SoM SC CPLD pin 'EN1' low. | Drive SoM SC CPLD pin 'EN1' high. | Usually used to enable/disable FPGA core-voltage supply. (Depends also on SoM's SC CPLD firmware). Note: Power-on sequence will be intermitted when S1-4 is set to OFF and functionality is supported by SoM. |
Connector J5 and J6
On the TE0706-02 carrier board there is one 50-pin IDC male connector socket available for access to the SoM's PL IO-bank-pins. 32 module's IO-pins are also usable as 18 LVDS-pairs and 8 IO's as single-ended (MIO0, MIO9 - MIO 15), which give access to the MIO0-bank of the Zynq-module if mounted. The available VCCIOs on this connector are 3.3V and M3.3VOUT from module. This connector gives also access to the LEDs of MagJack J2.
Place-holder J6 provides the possibility to mount and solder a VG96 backplane connector te get access to SoM's PL IO-bank-pins. 82 IO's are available on this connector, which are also usable as up to 41 LVDS-pairs. The available VCCIOs on this connector are 3.3V and M3.3VOUT from module and also the selectable PL I/O bank supply-voltages VCCIOA and VCCIOC. The pins A1, A2 are connected to the barrel jack for 5 V Power supply input.
On the TE0706-02 carrier board there is one 50-pin IDC male connector socket and a place-holder (VG96-Connector solder pads) J6 to provides access to SoM's PL IO-bank-pins. With this user interfaces, a large quantity of IO's are also usable as LVDS-pairs and different VCCIO's are available to operate the IO's properly.
Following table gives a summary of the optional pin-headers of the base-board:
Connector Designator | Connector Type | Count of IO's | Count of LVDS Pairs | Available VCCIO's | Interfaces |
---|---|---|---|---|---|
J5 | 50-pin IDC male | 40 | 16 | 3.3V, | access to the LEDs of MagJack J2 |
J6 | VG96-Connector | 82 | 41 | 3.3V, | PGOOD-, NOSEQ-Signal of SC-CPLD of mounted 4 x 5 SoM |
Power and Power-On Sequence
Power supply with minimum current capability of 3A for system startup is recommended.
Power Supply
TE0706-02 needs one single power supply with nominal of 5V.
Power Consumption
Power Input Pin | Max Current |
---|---|
VIN | 3A |
The power-consumption of TE0706-02 in conjunction with different 4 x 5 SoMs under certain configurations are depending on the used model of the 4 x 5 SoM and the custom-made FPGA-design on this SoM. Please refer to the TRM of the mounted 4 x 5 SoM to get information about the typical power consumption.
Power-On Sequence
It is not allowed to feed any voltage to any external I/O pin before there is no power indication on M3.3VOUT pins. Presence of 3.3V on B2B JB2 connector pins 9 and 11 indicates that module is properly powered up and ready. The 1.8V voltage-level on base-board for supplying PL I/O bank supply-voltages will be powered up after the module's 3.3V voltage-level has reached stable state and M3.3VOUT is available on the B2B-connector JB2, pins 9 and 11.
If VCCIOA or VCCIOC will be powered through the dedicated pins of external connector J6, then corresponding VCCIO jumpers J10 and J12 should be removed.
Base-board supply-voltage configuration
Refer to the 4 x 5 Module Integration Guide for VCCIO voltage options.
Note |
---|
Note: The corresponding PL I/O bank supply-voltages of the 4 x 5 SoM to the selectable base-board voltages VCCIOA, VCCIOB and VCCIOC are depending on the mounted 4 x 5 SoM and varying in order of the used model. Refer to the SoM's schematic for information about the specific pin assignments on module's B2B-connectors regarding the PL I/O bank supply-voltages and to the 4 x 5 Module integration Guide for VCCIO voltage options. |
Base-board supply-voltages (VCCIOA, VCCIOB, VCCIOC) selection-jumpers.
Following table shows how to configure the voltage-levels of base-board supply-voltages VCCIOA, VCCIOB and VCCIOC by jumper, 0-Ohm-resistor or by feeding the supply voltage through connector J6:
Supply Voltage by Jumper | Supply Voltage by 0-Ohm Resistor | Supply Voltage by Connector J6 | ||||
---|---|---|---|---|---|---|
Voltage Level | 1.8V | 3.3V | 1.8V | 3.3V | Variable | |
VCCIOA | J10: 1-2, 3 | J10: 1, 2-3 | - | R20 | J6 pin B32 | |
VCCIOB | J11: 1-2, 3 | J11: 1, 2-3 | R29 | R21 | - | |
VCCIOC | J12: 1-2, 3 | J12: 1, 2-3 | R30 | R22 | J6 pin B1 |
Jumper-Notification: 'Jx: 1-2, 3' means pins 1 and 2 are connected, 3 is open. 'Jx: 1, 2-3' means pins 2 and 3 are connected, 1 is open.
Only one supply-source is allowed to configure the base-board supply-voltages, either by jumper, by 0-Ohm-resistor or by connector J6. If a supply-voltage is configured by 0-Ohm-resistor or connector J6, then the corresponding configuration-jumper has to be removed. There aren't 0-Ohm-resistors and supply-voltages by connector J6 allowed if the corresponding base-board supply-voltage is configured by jumper. Vice versa jumpers and 0-Ohm-resistors have to be removed if supplying corresponding base-board supply-voltage by connector J6.
Note: If supplying base-board supply-voltages by connector J6, the module's internal 3.3V voltage-level on pins 9 and 11 of B2B-connector JB2 has to be reached stable state.
Note |
---|
It is recommended to set and measure the PL IO-bank supply-voltages before mounting of TE 4 x 5 module to avoid failures and damages to the functionality of the mounted SoM. |
Info |
---|
Header J9 exposes the SoM's VBAT-pin to an accessible connector. Please refer to the SoM's documentation regarding the operation conditions of this pin. |
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Units | Note |
---|---|---|---|---|
Supply voltage VIN | 4.75 | 5.25 | V | TPS2051DGN power distribution switch Note: USB-VBUS = VIN, if enabled. |
Storage temperature | -55 | +85 | °C | Marvell 88E1512 datasheet. |
Recommended Operating Conditions
Parameter | Min | Max | Units | Note |
---|---|---|---|---|
Supply Voltage Vin | 4.75 | 5.25 | V | - |
Operating temperature | 0 | +70 | °C | Commercial grade. |
Note |
---|
Please check components datasheets for complete list of absolute maximum and recommended operating ratings. |
Physical Dimensions
Board size: PCB 100mm × 64.5mm. Notice that the USB type A socket on the left and the Ethernet RJ-45 jacks on the right are hanging slightly over the edge of the PCB making the total width of the longer side approximately 106mm. Please download the assembly diagram for exact numbers.
Mating height of the module with standard connectors: 8mm
PCB thickness: 1.65mm
Highest parts on the PCB are USB type A socket and the Ethernet RJ-45 jacks, approximately 15mm. Please download the step model for exact numbers.
All dimensions are given in millimeters.
Operating Temperature Ranges
Commercial grade: 0°C to +70°C.
Industrial grade: -40°C to +85°C.
Board operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Weight
115g - Plain baseboard.
13g - VG96 connector.
Revision History
Hardware Revision History
Date | Revision | Notes | PCN | Documents |
---|---|---|---|---|
2016-06-28 | 02 | First production revision | - | |
- | 01 | Prototypes | - |
Hardware revision number is printed on the PCB board next to the module model number separated by the dash.
Document Change History
Date | Revision | Contributors | Description |
---|---|---|---|
2017-01-19 | Ali Naseri, Jan Kumann | Hardware revision 02 specific changes. | |
2016-01-06 | V1 | Ali Naseri | Initial document. |
Disclaimer
Include Page | ||||
---|---|---|---|---|
|