Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

HTML
<!--
General Notes:
Designate all graphics and pictures with a number and a description. For example "Figure 1: TE07xx-xx Block Diagram" or "Table 1: Initial delivery state". "Figure x" and "Table x" have to be formatted to bold.  
-->


Scroll Ignore

Download PDF version of this document.



Scroll pdf ignore

Table of Contents

Table of Contents

...

Scroll Only (inline)
Refer to https://shopwiki.trenz-electronic.de/de/Download/?path=Trenz_Electronic/XMOD/TE0791 for downloadabledisplay/PD/TE0791+TRM for the current online version of this manual and additionalother technicalavailable documentation of the product.

The Trenz Electronic TE0791-01 is an adapter board for use with the XMOD TE0790 board. The adapter board provides several connector types to get access to the signals and interfaces of the XMOD board. As further option footprints are available for JST Wire-To-Board IDC connectors with two different pin-assignments.

...

Signals, Interfaces and Pins

Image Added

Top View

Image Added

Bottom View flipped


Figure 3: Connector Location

2x6 Pin Header

The 2x6 pin header (2.54mm grid size, male) J2 of the TE0791 board have to be connected to the corresponding XMOD pin header on the TE0790 board. The signal assignment of the pin header on the TE0790 board depends on the configuration of its System Controller CPLD firmware.

...

J8 Pin Number J8 Pin NameSignalNote
1VIOVCCIOdepends on TE0790 voltage check TE0790 DIP-switch settings
2GNDGround-
3CTCK-
4DTDO-
5FTDI-
6HTMS-

...

NoteSignalJ1 Pin Name J1 Pin NumberJ1 Pin NumberJ1 Pin NameSignalNote
-UART TXDA 71CTCK-

-

UART RXDB82DTDO-
usable as GPIOLED on TE0790E93FTDI-
usable as GPIOButton on TE0790G104HTMS-
-Ground GND115GNDGround-
check TE0790 DIP-switch settingsVCC / VCCIO3.3V1263.3VVCC / VCCIOcheck TE0790 DIP-switch settings

Table 3: PMOD J1 signal assignment with standard TE0790 CPLD firmware

...

On the TE0791 board are footprints available for 10-pin JST Wire-To-Board IDC connectors J4 and J5 with two different pin-assignments, where all XMOD signals A - H are available. The pin- and signal-assignment with standard System Controller CPLD firmware of the XMOD board are as follows:

usable as GPIO

Pin NameJ4 Pin NumberJ5 Pin NumberSignalNote
A110UART TXD
B38UART RXD-
C29TCK-
D47TDO-
E56LED on TE0790usable as GPIO
F
7
65TDI-
G
6
74Button on TE0790usable as GPIO
H83TMS-
VIO92VCC / VCCIOcheck TE0790 DIP-switch settings
GND101Ground-

Table 4: IDC connector J4 and J5 signal assignment with standard TE0790 CPLD firmware

6-pin IDC Connector

On the TE0791 board are footprints available for 6-pin JST Wire-To-Board IDC connectors J3 and J6 with two different pin-assignments, where the XMOD signals C, D, F and H are available. At standard System Controller CPLD firmware, this signals create the JTAG interface of the XMOD board:

Pin NameJ3 Pin NumberJ6 Pin NumberSignalNote
C61TCK-
D52TDO-
F43TDI-
H34TMS-
VIO25VCC / VCCIOcheck TE0790 DIP-switch settings
GND16Ground-

Table 4:5: IDC connector J3 and J6 signal assignment with standard TE0790 CPLD firmware

Technical Specification

Physical Dimensions

...

All dimensions are given in millimeters and mil.


Figure 34: Board physical dimensions drawing.

...

DateRevision

Notes

PCNDocumentation Link
-01current available revision-TE0791-01

Table 56: Board hardware revision history.

...

Date

Revision

Contributors

Description

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd



John Hartfiel
  • add Figure 3: Connector Location
2017-10-19v.9Ali Naseri
  • initial document

Table 67: Document change history.

...