Page History
...
HTML |
---|
<!-- Template Revision 1.5 --> |
Scroll Only (inline) |
---|
Online version of this manual and other related documents can be found at https://wiki.trenz-electronic.de/display/PD/SC-CPLD-Firmware |
Scroll pdf ignore | ||||
---|---|---|---|---|
Table of contents
|
...
Info |
---|
2 Firmware variants with swapped external reset input and output direction are available. See Watchdog section of this document. Firmware (SC729_rev02plus03_default_teb0729_02_plus.jed) for J2-89 as external reset output and J2-91 as external reset input will be used as default firmware. |
...
Power
3.3V (EN_3V3) is enabled on power up.
Boot Mode
Boot Mode Pins routed through the CPLD. MIO2 and MIO3 are connected to GND via resistor.
...
Firmware Variants:
Figure1: Firmware (SC729_rev02org_03_teb0729_02_org.jed) for TEB0729 without HW modification,
| Figure2: Firmware (SC729_rev02plus_03_default_teb0729_02_plus.jed) for TEB0729 with HW modification,
|
...
IOs | B2B | Direction | Description |
---|---|---|---|
nRST | J2-89 | ininout | Main Reset to module |
nRST_IN | J2-91 | out | Main reset to carrier and PS_POR_B for approx. 1,9 us. |
...
IOs | B2B | Direction | Description |
---|---|---|---|
nRST | J2-89 | out | Main reset to carrier and PS_POR_B |
nRST_IN | J2-91 | ininout | Main Reset to module |
1V Power supply:
...
CPLD controlled WD on power up until FPGA takes control via WE_EN and WD_HIT input. CPLD WDI pulse frequency is set to approx. 1ms (Pulse width tw(CPLD)=507us )
nRST_IN is set to GND on power up for short time periode
FPGA Control:
WD_HIT pulse will be forwarded to WDI pin, if WE_EN is high and min 16 WD_HIT from FPGA was detected. To disable FPGA Control, set WD_EN to low.
...
Modus | Condition |
---|---|
Slow Blink | If PS_POR_B is low and appr. 16s after PS_POR_B goes up |
FPGA_IO | User defined, appr. 16s after PS_POR_B goes up and as long as PS_POR_B is high |
...
Info: On TEB0729, signal is connected to XMOD LED.
Appx. A: Change History and Legal Notices
Revision Changes
CPLD REV02 to REV03
- Add power up Watchdog main reset from CPLD
CPLD REV01 to REV02
- Bugfix for TE0729-REV02 Watchdog support
- Add 2 Variants for TEB0729-REV02 and TE0729-REV02_MOD support
- Change Pin FGPA_IO direction
- Change Pin BOARD_STAT output configuration
...
Date | Document Revision | CPLD Firmware Revision | Supported PCB Revision | Authors | Description | ||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
| REV02REV03 | REV02/REV02plus/REV03 |
|
| ||||||||||||||||||||||
2017-08-31 | v.14 | REV02 | REV02/REV02plus | John Hartfiel | |||||||||||||||||||||||
2017-08-23 | v.13 | REV02 | REV02/REV02plus | John Hartfiel |
| ||||||||||||||||||||||
2017-06-07 | REV02 | REV02/REV02plus |
|
| |||||||||||||||||||||||
All |
|
...