Page History
...
Scroll pdf ignore | |
---|---|
Table of Contents
|
Overview
HTML |
---|
<!-- Wiki Link: Go to Base Folder of the Module or Carrier, for example : https://wiki.trenz-electronic.de/display/PD/TE0712 --> |
...
The Carrier Board provides soldering-pads for VG96 connectors as place-holders to get access to the PL-IO-banks and other functional units of the mounted SoM.
Key Features
- Barrel jack for 5V power supply
- 2x RJ45 10/100-BaseT Ethernet MagJack with 2 integrated LEDs
- 1x RJ45 Gigabit Ethernet MagJack with 2 integrated LEDs.
- 2x Configuration EEPROM's, connected to SoM's I²C interface
- XMOD compatible header to connect the TE0790 USB2.0 adapter board
- JTAG and UART interface over XMOD header
- MicroSD Card socket, can be used to boot system
- USB2.0 socket (Option: USB Type A or Micro USB2.0 B)
- 4-bit DIP switch for SoM configuration (SoM's JTAG access and Bootmode)
- VG96 connector soldering-pads J8 for access to SoM's PL-IO-bank-pins, usable as LVDS-pairs
- VG96 connector soldering-pads J9 for access to further interfaces and IO's of the SoM
- 1 x user LED (red) routed to SoM
- 1 x user push-button routed to SoM (Reset function at standard configuration)
- Pin headers to set PL-IO-bank's VCCIO with jumper
Additional assembly options are available for cost or performance optimization upon request.
Block Diagram
Figure 1: TEB0729-02 block diagram.
Main Components
Figure 2: TEB0729-02 main components.
- 5V barrel jack, J12
- RJ-45 Gigabit Ethernet MegJack, J3
- RJ-45 10/100-BaseT Ethernet MegJack, J4
- RJ-45 10/100-BaseT Ethernet MegJack, J5
- VG96 connector placeholder, J9
- XMOD (TE0790) header, JB3
- 2-pin header for VBAT-IN supply-voltage, J2
- 2x6 pin header for setting VCCIO_33, J6
- 2x6 pin header for setting VCCIO_13, J7
- MicroSD Card socket, J1
- Red LED, D1
- Push Button, S1
- Micro USB2.0 B Receptacle (optional USB2.0 Type A socket)
- VG96 connector placeholder, J8
- B2B Connector, JB1
- B2B Connector, JB2
- 4-bit DIP-switch, S2
Initial Delivery State
Storage device name | Content | Notes |
---|---|---|
Configuration EEPROM, U1 | Empty | Not programmed |
Configuration EEPROM, U2 | Empty | Not programmed |
Table 1: Initial delivery state of programmable devices on the module.
Signals, Interfaces and Pins
HTML |
---|
<!-- Connections and Interfaces or B2B Pin's which are accessible by User --> |
B2B Connector
The TEB0729 Carrier Board's Board-to-Board Connectors (B2B) have the same pin-assignment as the mounted Zynq SoM due to its hermaphroditic structure. By this connectors, the MIO- and PL-IO-bank's pins and further interfaces of the Zynq SoM can be accessed. A large quantity of these I/O's are also usable as LVDS-pairs. The connectors provide also VCCIO voltages to operate the I/O's properly.
...
Table 2: General overview of PL I/O signals and SoM's interfaces connected to the B2B connectors.
VG96 Connector
The TEB0729 Carrier Board has soldering pads provides as place-holders to mount VG96 connectors J8 and J9 to get access the PL-IO-bank's pins and further interfaces of the Zynq SoM. With mounted VG96 connectors, SoM's IO's are available to the user, a large quantity of these I/O's are also usable as LVDS-pairs.
...
Table 3: General overview of PL I/O signals, SoM's interfaces and control signals connected to the VG96 connectors.
HW-modification Concerning Reset-Signals
1) The pins with the schematic net names 'NRST_IN' (JB2-89) and 'NRST_OUT' (JB2-91) are swapped as part of a HW-modification to rework the Reset-signals of the Carrier-Board in conjunction with the TE0729 SoM.
Refer to the SC CPLD documentation, section "Watchdog" to get further detailed information about the Reset-functionality of the Carrier Board and SoM before and after the HW-modification and the required SC CPLD firmware revision of the TE0729 SoM for each version of the SoM.
JTAG Interface
JTAG access to the mounted SoM is provided through B2B connector JB2 and is also routed to the XMOD header JB3. With the TE0790 XMOD USB2.0 to JTAG adapter, the Zynq chip on the mounted SoM can be programed via USB2.0 interface.
...
Table 4: JTAG interface signals.
UART Interface
UART interface is available on B2B connector JB2. With the TE0790 XMOD USB2.0 adapter, the UART signals can be converted to USB2.0 interface signals:
...
Table 5: UART interface signals.
I²C Interface
Two I²C interfaces are provided on B2B connector JB2. I²C0 interface is connected to the Configuration EEPROMs U1 and U2 and is dedicated to these on-board peripherals. Interface I²C1 is routed to the VG96 connector J9 and is available to the user for general purposes:
...
Table 6: I²C interface signals.
SD IO Interface
The SD IO interface of the SoM's Zynq chip (MIO-bank) is routed to the on-board MicroSD Card socket J1. By this interface, the Zynq chip can be booted from an inserted MicroSD Card:
...
Table 7: SD IO interface signals.
USB2.0 Interface
The TEB0729 Carrier Board is equipped with a Micro USB2.0 B (receptacle) socket J11 with board-revision TEB0729-02B, USB2.0 Type A socket is fitted on board-revision TEB0729-02A.
...
Table 8: USB2.0 interface signals and connections.
Gigabit Ethernet Interface
The TEB0729 Carrier Board is fitted with one RJ-45 Gigabit Ethernet Magnetic jack J3. The MegJack has two integrated LEDs (both green), its signals are routed as MDI (Media Dependent Interface) to the B2B connector JB2, where they can be accessed by the GbE PHY transceiver of the mounted SoM:
...
Table 10: GbE SGMII signals and connections.
10/100-BaseT Ethernet Interface
The TEB0729 Carrier Board is also fitted with two additional RJ-45 MegJacks providing 10/100-BaseT Ethernet interfaces. This interfaces are routed to the B2B connector JB2
...
Table 11: 10/100-BaseT Ethernet interfaces signals and connections.
XMOD FTDI JTAG-Adapter Header
The JTAG interface of the mounted SoM can be accessed via header JB3, which has a 'XMOD FTDI JTAG Adapter'-compatible pin-assignment. So in use with the XMOD-FT2232H adapter-board TE0790 the mounted SoM can be programmed via USB interface. The TE0790 board provides also an UART interface to the Zynq SoM which can be accessed by the USB2.0 interface of the adapter-board while the signals between these serial interfaces will be converted. The adapter-board offers also two GPIO's, one with an indication LED (pin JB3-9 (E)) and another one with a low-active push button (pin JB3-11 (G)).
...
Table 13: XMOD module DIP-switch positions for voltage configuration.
On-board Peripherals
HTML |
---|
<!-- Components on the Module, like Flash, PLL, PHY... --> |
Configuration EEPROM
The TEB0729 Carrier Board is equipped with two Configuration EEPROMs U1 and U2 from Microchip.
...
The Configuration EEPROMs are connected to the I²C0 interface of the Zynq's MIO-bank via B2B connector JB2.
4-bit DIP-switch
Table below describes DIP-switch S2 settings for configuration of the mounted SoM:
...
Table 14: DIP-Switch S2 SoM configuration settings.
TE0729 Bootmodes
If TE0729 is mounted, following bootmodes can be configured by setting the DIP-switches S2-2 and S2-3:
...
The selected bootmode via DIP-switch S2 depends also on the current configured SC CPLD firmware on the mounted SoM and may vary.
VCCIO Setting Jumper
The Carrier Board VCCIO for the PL IO-banks of the mounted SoM are selectable by the jumpers J6 and J7.
...
Table 16: VCCIO jumper settings.
RTC Buffer Voltage Supply Header
The buffer voltage of the SoM's RTC can be supplied through the header J2. Refer to the SoM's TRM for recommended voltage range and absolute maximum ratings.
Push Button
The Carrier Board's push button S1 is connected to the 'NRST_IN' signal, the function of the button is to trigger a reset of the mounted SoM by driving the reset-signal 'NRST_IN' to ground.
On-board LEDs
LED | Color | Connected to | Description and Notes |
---|---|---|---|
D1 | Red | 'MIO9', pin JB2- 88 | user LED |
Table 17: On-board LEDs.
Power and Power-On Sequence
HTML |
---|
<!-- If power sequencing and distribution is not so much, you can join both sub sections together --> |
Power Consumption
The maximum power consumption of the Carrier Board depends mainly on the mounted SoM's FPGA design running on the Zynq chip.
...
Warning |
---|
To avoid any damage to the module, check for stabilized on-board voltages and VCCIO's before put voltages on PL I/O-banks and interfaces. All I/Os should be tri-stated during power-on sequence. |
Power Distribution Dependencies
The Carrier Board needs one single power supply voltage with a nominal value of 5V. Following diagram shows the distribution of the input voltage '5VIN' to the on-board components on the mounted SoM:
...
Figure 3: Board power distribution diagram.
Power Rails
Module Connector (B2B) Designator | VCC / VCCIO | Direction | Pins | Notes |
---|---|---|---|---|
JB1 | VIN33 | Out | Pin 1, 2, 3, 4, 5, 6 | 3.3V module supply voltage |
VCCIO_13 | Out | Pin 101, 102 | PL IO-bank VCCIO | |
VCCIO_33 | Out | Pin 29, 30 | PL IO-bank VCCIO | |
3.3V | In | Pin 65, 66 | voltage output from module | |
JB2 | 1.8V | In | Pin 49 | voltage output from module |
2.5V | In | Pin 13 | voltage output from module | |
USB-VBUS | Out | Pin 107 | USB Host supply voltage | |
VBAT_IN | Out | Pin 118 | RTC buffer voltage |
...
Table 23: Power pin description of XMOD/JTAG Connector.
Board to Board Connectors
Include Page | ||||
---|---|---|---|---|
|
Variants Currently In Production
Module Variant | Operating Temperature | USB Socket | Temperature Range |
---|---|---|---|
TEB0729-02-A | -40°C to +125°C | USB2.0 Type A socket fitted | Industrial |
TEB0729-02-B | -40°C to +125°C | Micro USB2.0 B socket fitted | Industrial |
Table 24: Module variants.
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
5VIN supply voltage | -0.3 | 7 | V | MP5010A, EN6347QI data sheet |
Storage temperature | -65 | 150 | °C | - |
Table 25: Module absolute maximum ratings.
Recommended Operating Conditions
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
5VIN supply voltage | 4.75 | 5.25 | V | USB2.0 specification concerning 'VBUS' voltage |
Operating temperature | -40 | 125 | °C | - |
Table 26: Module recommended operating conditions.
Operating Temperature Ranges
Industrial grade: -40°C to +85°C.
...
Please check the operating temperature range of the mounted SoM, which determine the relevant operating temperature range of the overall system.
Physical Dimensions
Board size: 107.70 mm × 100 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 8 mm.
PCB thickness: ca. 1.65mm.
Highest part on the PCB is the Ethernet RJ-45 jack, which has an approximately 17 mm overall height. Please download the step model for exact numbers.
...
Figure 4: Board physical dimensions drawing.
Revision History
Hardware Revision History
Date | Revision | Notes | PCN | Documentation Link |
---|---|---|---|---|
- | 01 | First Production Release | - | TEB0729-01 |
- | 02 | Second Production Release | - | TEB0729-02 |
...
Figure 5: Module hardware revision number.
Document Change History
HTML |
---|
<!-- Generate new entry: 1.add new row below first 2.Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number 3.Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description. --> |
...
Table 28: Document change history.
Disclaimer
Include Page | ||||
---|---|---|---|---|
|