Page History

...

Additional assembly options are available for cost or performance optimization upon request.

Block Diagram

Put your block diagram here...

...

1. SFP+ 2x1 cage with integrated LED light pipes, J9
2. DisplayPort connector, J12
3. USB3 A 2x , RJ45 1x (stacked), J13
4. FMC connector (FMC B), J4
5. FMC B cooling fan, M2
6. FMC connector (FMC C), J8
7. FMC C cooling fan, M3
8. FMC connector (FMC D), J7
9. FMC D cooling fan, M4
10. FMC connector (FMC E), J6
11. FMC E cooling fan, M5
12. I²C programming header of on-board PLL clock generator U17, J22
13. 4-Wire PWM fan connector, J23
14. Main Power Jack 24V, J1
15. CAN bus D-SUB 9-pin male connector, J3
16. CAN bus 6-pin header male, J15
17. XMOD JTAG header for access to System Controller CPLD, J35
    
18. XMOD JTAG header for access to Zynq MPSoC, J24
19. FMC B cooling fan, M3
20. MicroSD Card socket (on bottom side), J16
21. DisplayPort connector, J13
22. USB3.0 A 2x , RJ45 1x (stacked), J7
23. SFP+ 2x1 cage, J14
24. PCIe x16 connector (one PCIe lane connected), J11
25. FMC HPC connector, J5
26. FMC-Fan connector 5V, J19
27. USB3.0 connector, J8
28. PC-BEEPER 4-pin header, J23
29. SMA coaxial connector (SI5338A clock output), J32
30. SMA coaxial connector (clock input to MPSoC module), J33
31. MMC Card socket, J27
32. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J4
33. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J1
34. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J3
35. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J2
36. CAN bus 6-pin header, J29
37. CAN bus 10-pin connector, J24
38. ARM JTAG  20-pin connector, J30
39. ATX-24 power supply connector, J20
40. 4-Wire PWM fan connector, J35
41. JTAG/UART header ('XMOD FTDI JTAG Adapter'-compatible) for access to MPSoC module, J12
42. JTAG/UART header ('XMOD FTDI JTAG Adapter'-compatible) for access to System Controller CPLDs, J28
43. Power Jack 2.1mm 12V, J25
44. 4-bit DIP-switch, S5
45. Power Button, S1
46. Samtec FireFly connector  for reverse loopback, J21/J22
47. Samtec FireFly connector (4 GT lanes bidirectional), J6/J15
48. SATA header, J31
49. 4-Wire PWM fan connector, J26
50. I²C interface of programmable on-module PLL (10-pin header), J17
51. Reset Button, S2
52. INTEL HDA 9-pin header, J9
53. Intel front panel (PWR-/RST-Button, HD-/PWR-LED) 9-pin header, J10
54. Samtec FireFly connector J6/J15 I²C interface (3-pin header), J34
55. 4-bit DIP-switch, S4
56. PMOD connector, P3
57. PMOD connector, P1
58. 4-Wire PWM fan connector, J33
59. Battery Holder CR1220, B1
60. SMT coaxial connector (PLL Si5345A U17 clock input), J25
61. Push Button, S1
62. Push Button, S2
63. DDR4 SO-DIMM socket, U3
64. 4-bit DIP-switch, S4
65. 4-bit DIP-switch, S3
66. FMC connector (FMC A), J10
67. FMC A cooling fan, M1
68. FMC connector (FMC F), J21
69. FMC F cooling fan, M6
70. NGFF M.2 PCIe socket (Key M), U2
71. SD Card socket, J11
72. User LEDs (3x green, 1x red) with LED light pipe, D13 ... D16
    
73. Green LEDs dedicated to USB3 hub U4, D17 ... D19
74. Red LED indicating FPGAs 'DONE' signal, D6
75. 4-Wire PWM fan connector, J2
76. Battery Holder CR1220, B1Xilinx Zynq Ultrascale+ MPSoC, U1
    

Initial Delivery State

...

Refer also to the documentation of the SC CPLD firmware of the TEB0911 board, section 'boot mode'.

Signals, Interfaces and Pins

...