Page History
...
The Trenz Electronic TEM0002-01 SmartBerry with Raspberry Pi form factor, is an industrial-grade module based on Microsemi SmartFusion2 SoC (System on a Chip) including a Cortex-M3 and FPGA Fabric with . The Module has 128MB DDR3 SDRAM, a Gigabit Ethernet PHY, four PMODs, a GPIO Pin header compatible to the Raspberry Pi pinout and a Micro USB to UART interface. SmartFusion2 combiens combines a 166 MHz Cortex-M3 core with 256 KByte Flash, 80 KByte SRAM and a 12 kLUT FPGA Core Logiccore logic.
Key Features
- Microsemi SmartFusion2 SoC FPGA (M2S010)
- 128 MByte DDR3 SDRAM
- On board power converters for all needed voltages
- 40 pin header (compatible to Raspberry Pi pinout)
- 4 x 12 pin PMODs
- Gigabit Ethernet PHY with RGMII interface
- JTAG and UART via Micro USB
- 3 pin header for Live Probes
- 2 x User Button
- 2 x status LED
- 1 x RGB LED
...
The module provides four 2x6 female PMOD connectors. Two of the headers (P1 P2 and P2P3) are arranged to use as dual 12 pin PMOD. According to the standard on all four headers Pin 5 and 11 are connected to ground, 6 and 12 to 3.3V.
FPGA SoC Signal | Pin | Label | PMOD Signal | PMOD PMOD Pin / Signal |
---|---|---|---|---|
MSIO71PB7 | U2-F3 | P1 | PB-01 | PB-01 |
MSIO71NB7 | U2-F4 | P1 | PB | PB-02 |
MSIO68NB7 | U2-E3 | P1 | PC | PB-03 |
MSIO80NB7 | U2-H4 | P1 | PD | PB-04 |
MSIO75PB7 | U2-G4 | P1 | PB-05 | |
MSIO70PB7 | U2-E1 | P1 | PB-06 | |
MSIO67NB7 | U2-E5 | P1 | PB-07 | |
MSIO78NB7 | U2-G3 | P1 | PB-08 | |
MSIO79PB7 | U2-G1 | P2 | PC-01 | |
MSIO79NB7 | U2-F1 | P2 | PC-02 | |
MSIO70NB7 | U2-E2 | P2 | PC-03 | |
MSIO64PB7 | U2-C1 | P2 | PC-04 | |
MSIO78PB7 | U2-G2 | P2 | PC-05 | |
MSIO70PB7 | U2-E1 | P2 | PC-06 | |
MSIO68PB7 | U2-D2 | P2 | PC-07 | |
MSIO64NB7 | U2-C2 | P2 | PC-08 | |
MSIO117NB4 | U2-Y16 | P3 | PA-01 | |
MSIO117PB4 | U2-Y15 | P3 | PA-02 | |
MSIO112PB4 | U2-W13 | P3 | PA-03 | |
MSIO110PB4 | U2-V12 | P3 | PA-04 | |
MSIO118PB4 | U2-W15 | P3 | PA-05 | |
MSIO112NB4 | U2-W14 | P3 | PA-06 | |
MSIO105NB4 | U2-Y13 | P3 | PA-07 | |
MSIO105NB4 | U2-Y13 | P3 | PA-08 | |
MSIO4PB2 | U2-P20 | P4 | PD-01 | |
MSIO3NB2 | U2-R20 | P4 | PD-02 | |
MSIO2NB2 | U2-T19 | P4 | PD-03 | |
MSIO0PB2 | U2-V20 | P4 | PD-04 | |
MSIO6NB2 | U2-P19 | P4 | PD-05 | |
MSIO3PB2 | U2-T20 | P4 | PD-06 | |
MSIO1NB2 | U2-U19 | P4 | PD-07 | |
MSIO0NB2 | U2-V19 | P4 | PD-08 |
...
JTAG access to the SoC components is provided through the micro usb connector via the FTDI usb to UART bridge. Depending on the jumper J6 the JTAGSEL signal SW3 switches the JTAG interface to either the FPGA fabric TAP (open, high) or the Cortex-M3 JTAG debug interface (closed, low). JTAG signals are powered by 3.3V.
FTDI signal | pin | JTAG Signal | Microsemi SmartFusion2 SoC FPGA pin |
---|---|---|---|
ADBUS0 | U3-12 | TCK | U2-W19 |
ADBUS1 | U3-13 | TDI | U2-V16 |
ADBUS2 | U3-14 | TDO | U2-Y20 |
ADBUS3 | U3-15 | TMS | U2-V17 |
...