Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Page properties
hiddentrue
idComments

In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are:

  • Overview of the board (point out the LEDs, Ethernets, Switches and etc on the board overview)
  • Explain Switches functionality
  • Explain user LEDs
  • Explain the UART connection

  • Refer to the Reference Design

Scroll pdf ignore

Table of Contents

Table of Contents

Overview


scroll-pdf-ignore

Table of Contents

Table of Contents

TEB0728 with TE0728

Overview


scroll-title
anchorFigure_anchornameOverview
titleModule Board Overview


Scroll Ignore
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue

draw.io Diagram
bordertruefalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision11
diagramNameTE0728_OV
simpleViewerfalse
width
linksauto
tbstylehidden
diagramWidth641
revision3


Scroll Only


  1. Barrel Jack Power Supply
  2. XMOD JTAG Adapter
  3. SD card holder
  4. Reset
  5. Boot mode Jumper
  6. Carrier LEDs (Red,Yellow,Green) D1
  7. Ethernet Socket
  8. Module LEDs (Green D4, Red D8)

Power supply

The input power supply must be mentioned.

Page properties
hiddentrue
idComments
Note

Single 5V power supply with minimum current capability of 2.5A is recommended to operate the board.power on the board. 

Scroll Title
anchorTable_DIP_PWR
titlePower Supply

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Overview 1

Supply VoltageMin CurrentNote

J9

5 V

2.5 A



DIP-Switches and Push Buttons

Explain all DIP switches functionality.

Page properties
hiddentrue
idComments
Note

There is a switch (S1) which is connected to RESET signal which , it resets the system entirely.

Scroll Title
anchorTable_DIP_SwitchPB
titleDIP Switchs and Switches /Push Buttons

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Signal

Overview 4

Designator
Connected toB2BActive Level

S1

RESET

S1

J2-7

Active High


There are is no DIPs on TE0728. In case of TE0790 (XMOD) usage, see power supply section.DIPs mode.

Jumpers

Page properties
hiddentrue
idComments

Explain all Jumpers functionality and connection.


Scroll Title
anchorTable_Jumpers
titleJumpers

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Overview 5Connected toB2BNote
J4Boot_RJ2-11Open: QSPI
Short: SD Card


LEDs

Explain all user LEDs functionality and

connection

connections.

Page properties
hiddentrue
idComments
Note

There are three user LEDs on the carrier TEB0728 which can be used for variant purposes.

Scroll Title
anchorTable_OBP_LED
titleOn-board Carrier LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Designator
Overview 6ColorConnected toB2BActive LevelNote
D1-ARedMIO48J2-30Active highUser LED
D1-BYellowMIO49J2-38Active highUser LED
D1-CGreenMIO50J2-36Active highUser LED


Furthermore, there are two user LEDs on module TE0728.

Scroll Title
anchorTable_LED
titleModule LEDs

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Overview 8ColorConnected toB2BActive LevelNote
D4GreenBank33 pin V18-Active highUser LED
D9GreenDONE_0

DONE pin
D8RedMIO7-Active highUser LED


JTAG/UART

Explain JTAG or UART connection breifly.

Page properties
hiddentrue
idComments
Note

JTAG and UART is possible over miro USB connector.

miroUSB UART is connected to PL IO (RX: Pin H13, TX: Pin H14).

connections are available through XMOD JTAG adapter. For more information refer to TE0790.

DIP Switch on the XMOD JTAG adapter must be set  like the following table.

Scroll Title
anchorTable_XMOD_JTAG
titleXMOD JTAG DIP Switch

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Overview 2DIP SwitchSetting
JB11ON
2OFF
3OFF
4ON


Reference Designs

Page properties
hiddentrue
idComments

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

Notes

Page properties
hiddentrue
idComments

In this Section you must refer to the Resources Page for the particular module.

For Example: TE0728 Resources