Versions Compared

Old Version 9

changes.mady.by.user Martin Rohrmüller

Saved on

compared with

New Version Current

changes.mady.by.user Martin Rohrmüller

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Scroll Title
anchorFigure_Overview
titleBoard Overview


Scroll Ignore
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue

draw.io Diagram
bordertruefalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxfalse
revision5
diagramNameTEF1002 Overview
simpleViewerfalse
width
diagramWidth638
linksauto
tbstyletop
diagramWidth636revision3
draw.io Diagram
bordertruefalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxfalse
revision4
diagramNameTEF1002_Overview_bottom
simpleViewerfalse
width
linksauto
tbstyletop
diagramWidth635631


Scroll Only


  1. 4x5 module connectors
  2. Jumper J4 (VCCIOA)
  3. Jumper J7 (VCCA_SD)
  4. Dip swiches switches S2 and S3
  5. 6-pin PCI-E PCIe ATX Power Connector
  6. micro USB  connector for FTDI USB to JTAG/UART bridge
  7. Push Reset push button
  8. Power LED
  9. Status LED
  10. top load microSD card cage

Power supply

...

Single 12V power supply with minimum current capability of 3A is recommended to power on the board via the 6-pin PCI-E PCIe ATX connector. 

DIP-Switches and Push Buttons

...

Select dip switch settings according to the attached 4x5 module and your needs. Compare Dip switch setting with TRM of your module and table in TRM of TEF1002. Following a general configuration is shown.

Scroll Title
anchorTable_DIP_PB
titleDIP Switches /Push Buttons

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue


DipSettingNote
S1
Push button configured by CPLD as reset

S2-1

OFF

OFF, OFF, OFF selects FMC _VADJ OFF. The choice OFF, ON, OFF selects 1.8V FMC_VADJ, which is a valid bank power for TE0720.


S2-2OFFON
S2-3OFF
S2-4ONOFFSelects 4x5 module SOC/FPGA JTAG
S2-5ONOFF
S2-6OFF
S2-7ONModule  power enable.
S2-8ONOFFUse extended Extended power sequenzing (if implemented).
S3-1OFF/ONFor Zynq modules: Primary Boot Mode SD/QSPI. OFF corresponds to boot from SD card.
S3-2OFFON for TE0720 (overide Overide automatic enable FMC_VADJ). For TE0720 bank .  (1)(2)


(1) Set to ON for TE0720 because bank 34 has to be

...

powered to start up. Therefore FMC VADJ has to be set to a valid value e.g. 1.

...

8V (See S2-1 to S2-3).

(2) For TE0820 set to on to use CLK0 (VCCO 65). Therefore FMC VADJ has to be set to a valid value e.g. 1.8V (See S2-1 to S2-3).

Jumpers

Page properties
hiddentrue
idComments

Explain all Jumpers functionality and connection.

For Jumper J7 compare TRM of actually used 4x5 module. The voltage of the bank where the SDIO signals are connected reside has to selected. J4 selects the module bank voltage VCCIOA. It has to be selected in accordance with IO voltage of signals connected to FFA and FFB. If both FFA and FFB are not used any setting is ok. Do not leave open (communication of 4x5 module with TEF1002 CPLD is only possible with availabe VCCIOA)!

...

There are four LEDs on the board. Two of them are user LEDS not further described here. Compare corresponding table in TEF1002 TRM.

...

JTAG (first FTDI port) and UART (second FTDI port) is over available via MicroUSB connector available. External JTAG Programmer is not needed.

...

Page properties
hiddentrue
idComments

In this Section you must refer to the Reference Design (Test board) for the particular module.

For Example: TE0728 Reference Designs

  • Use e.g. the Test board Reference Design of the installed 4x5 module.
  • For TE0820 on this carrier TE0820 TD TEF1002, including PCIe endpoint and SATA, is available.

Notes

Page properties
hiddentrue
idComments

In this Section you must refer to the Resources Page for the particular module.

For Example: TE0728 Resources

...