- Attache 4x5 module to TEF1002
- Select Voltage VCCA_SD of 4x5 module bank where SD-Card is connected by Jumper J7 (1-2 →3.3V; 2-3 1.8V). Compare TRM of actually used 4x5 module.
- Select VCCIOA Voltage by setting J4 (1-2 →3.3V; 2-3 1.8V). If both FFA and FFB are not used any setting is ok. Do not leave open (communication of 4x5 module with TEF1002 CPLD is only possible with availabe VCCIOA)!
Select dip switch settings according to the attached 4x5 module and your needs:
| Dip | Setting | Note |
|---|
S1-1 | OFF | FMC _VADJ OFF. The choice OFF, ON, OFF selects 1.8V FMC_VADJ, wich is a valid bank power for TE0720.
|
| S1-2 | OFF |
| S1-3 | OFF |
| S1-4 | ON | Selects 4x5 module SOC/FPGA JTAG |
| S1-5 | ON |
| S1-6 | OFF |
| S1-7 | ON | Module power enable. |
| S1-8 | ON | Use extended power sequenzing. |
| S2-1 | OFF/ON | For Zynq modules: Primary Boot Mode SD/QSPI. |
| S2-2 | OFF | ON for TE0720 (overide automatic enable FMC__VADJ). For TE0720 bank bank 34 has to be powerded to start up. Therefore FMC VADJ has to be set to a valid value e.g. 1.8V |
- Connect 12V ATX connector
- Connect mico USB J10 to PC
- Use Xilinx JTAG tools to programm FPGA or for Zynq modules use micro SD Card.
- Use e.g. Putty on PC to check for UART interactions.
| Page properties |
|---|
|
In this section you must explain how to power on the board and run the Reference Design (test board) on the particular module. The main points must be mentioned are: |
| Scroll pdf ignore |
|---|
Table of Contents |
TExxxx with TExxxx
Overview
| Scroll Title |
|---|
| anchor | Figure_Overview |
|---|
| title | Board Overview |
|---|
|
| Scroll Ignore |
|---|
| scroll-pdf | true |
|---|
| scroll-office | true |
|---|
| scroll-chm | true |
|---|
| scroll-docbook | true |
|---|
| scroll-eclipsehelp | true |
|---|
| scroll-epub | true |
|---|
| scroll-html | true |
|---|
| | draw.io Diagram |
|---|
| border | true |
|---|
| viewerToolbar | true |
|---|
| |
|---|
| fitWindow | false |
|---|
| diagramName | TEF1002 Overview |
|---|
| simpleViewer | false |
|---|
| width | |
|---|
| diagramWidth | 641 |
|---|
| revision | 1 |
|---|
|
|
|
Power supply
| Page properties |
|---|
|
The input power supply must be mentioned. |
Single ??V power supply with minimum current capability of ??A is recommended to power on the board.
DIP-Switches and Push Buttons
| Page properties |
|---|
|
Explain all DIP switches functionality. |
There is a switch (S??) which is connected to RESET signal, it resets the system entirely.
| Scroll Title |
|---|
| anchor | Table_DIP_PB |
|---|
| title | DIP Switches /Push Buttons |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| style | |
|---|
| widths | |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
Signal | Designator | B2B | Active Level |
|---|
|
|
|
|
|
There is no DIPs on TExxxx. In case of TE0790 (XMOD) usage, see DIPs mode.
Jumpers
| Page properties |
|---|
|
Explain all Jumpers functionality and connection. |
| Scroll Title |
|---|
| anchor | Table_Jumpers |
|---|
| title | Jumpers |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| style | |
|---|
| widths | |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| Designator | Connected to | B2B | Note |
|---|
| Boot_R |
| Open: | | Short: |
|
LEDs
| Page properties |
|---|
|
Explain all user LEDs functionality and connections. |
There are three user LEDs which can be used for variant purposes.
| Scroll Title |
|---|
| anchor | Table_LED |
|---|
| title | Carrier LEDs |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| style | |
|---|
| widths | |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| Designator | Color | Connected to | B2B | Active Level | Note |
|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Scroll Title |
|---|
| anchor | Table_LED_Module |
|---|
| title | Module LEDs |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| style | |
|---|
| widths | |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| Designator | Color | Connected to | Active Level | Note |
|---|
|
|
|
|
|
|
|
|
|
|
|
| Scroll Title |
|---|
| anchor | Table_LED_Carrier |
|---|
| title | Carrier LEDs |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| style | |
|---|
| widths | |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| Designator | Color | Connected to | Active Level | Note |
|---|
|
|
|
|
|
|
|
|
|
|
|
JTAG/UART
| Page properties |
|---|
|
Explain JTAG or UART connection breifly. |
JTAG and UART connections are available through mini USB connector.
| Scroll Title |
|---|
| anchor | Table_UART |
|---|
| title | UART |
|---|
|
| Scroll Table Layout |
|---|
| orientation | portrait |
|---|
| sortDirection | ASC |
|---|
| repeatTableHeaders | default |
|---|
| style | |
|---|
| widths | |
|---|
| sortByColumn | 1 |
|---|
| sortEnabled | false |
|---|
| cellHighlighting | true |
|---|
|
| Designator | Connected to | B2B Pin | XMOD Header JB? | Direction | Note |
|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
Reference Designs
| Page properties |
|---|
|
In this Section you must refer to the Reference Design (Test board) for the particular module. For Example: TE0728 Reference Designs |
Notes
| Page properties |
|---|
|
In this Section you must refer to the Resources Page for the particular module. For Example: TE0728 Resources |