Versions Compared

Old Version 37

changes.mady.by.user Martin Rohrmüller

Saved on

compared with

New Version 38

changes.mady.by.user Martin Rohrmüller

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Scroll Title
anchorTable_SIP_JTG
titleJTAG pins connection

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Signal

B2B Connector Pin

Note
M_TCKU5-131CPLD Firmware dependent TE0703 CPLD - CC703S#CC703S, dependent on Dip switches linked to Module JTAG Port on JB2.
M_TDIU5-136
M_TDOU5-137
M_TMSU5-130
FT_B_TXU5-139CPLD Firmware dependent TE0703 CPLD - CC703S#CC703S, linked to Module primary UART on JB1.
FT_B_RXU5-138
ADBUS7U5-142CPLD Firmware dependent TE0703 CPLD - CC703S#CC703S, currently not used.
ADBUS4U5-143
ACBUS4U5-141
ACBUS5

U5-140

BDBUS2U5-133
BDBUS3U5-132
BDBUS4U5-128
BDBUS5U5-127
BDBUS6U5-126
BDBUS7U5-125
BCBUS0U5-122
BCBUS1U5-121


LEDs

There are four on-board LEDs. D3 and D4 are  connected to the B2B connector JB2 pins FLED1 and FLED2 respectively and can be read by CPLD firmware. See TE0703 CPLD - CC703S#CC703S-LED.

...

Scroll Title
anchorTable_OBP_DIS
titleDip-Switches

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

SwitchONOFFNotes
S2-1Force CD Pin to module to GNDset CD Pin to module to SD CD PinTE0703 CPLD - CC703S#CC703S-SD
S2-2Module FPGA  JTAG access ( if S2-3 ON)Module CPLD JTAG access ( if S2-3 ON)TE0703 CPLD - CC703S#CC703S-JTAG
S2-3Module FPGA/CPLD  JTAG access (  depends on S2-3)Carrier CPLD  JTAG accessTE0703 CPLD - CC703S#CC703S-JTAG
S2-4 Boot from SD Card (set Pin to GND)Boot from QSPI flash on module (set Pin to VDD)

TE0703 CPLD - CC703S#CC703S-BootMode
Boot Mode is also  module dependsalso depends on module.


Mode status is displayed on TE0703 LEDs, see TE0703 CPLD - CC703S#CC703S-LED.

...

Scroll Title
anchorTable_OBP_JUM
titleJumpers

Scroll Table Layout
orientationportrait
sortDirectionASC
repeatTableHeadersdefault
style
widths
sortByColumn1
sortEnabledfalse
cellHighlightingtrue

Power RailJumper

1.8V

3.3VNotes
VCCIOAJ51-22-3-
VCCIOBJ81-22-3-
VCCIOCJ91-22-3-
VCCIODJ101-22-3-
VCCAJ111-22-3SD IO level shifter Voltage Selectionvoltage selection (module side), compare with TRM of attached Module


...

draw.io Diagram
borderfalse
viewerToolbartrue
fitWindowfalse
diagramDisplayName
lboxtrue
revision23
diagramNameREV_TE0703-06
simpleViewerfalse
width400200
linksauto
tbstyletop
diagramWidth199194

Document Change History

Date

Revision

Contributors

Description

Page info
infoTypeModified date
dateFormatyyyy-MM-dd
typeFlat

Page info
infoTypeCurrent version
prefixv.
typeFlat
showVersionsfalse

Page info
infoTypeModified by
typeFlat
showVersionsfalse

  • updating updated to REV06
  • updating updated to TRM style 2.12

2018-06-13


v.29

Ali Naseri
  • updating operating conditions
2017-02-07v.28John Hartfiel
  • Add DIP setting description
2017-11-09v.26John Hartfiel
  • add B2B connector section
2017-02-21

v.19


Jan Kumann
  • New block diagram.
2017-02-02

v.16

Jan Kumann
  • New board image with silk screen pin markings for VG96 connectors J1 and J2.
2016-12-22

v.14

Jan Kumann
  • Block diagram added.
2016-12-08
v.10

Jan Kumann

  • Document structure revised.
2016-12-05

v.5

John Hartfiel
  • Corrected Boot Mode table.
2016-09-06

v.1

Jan Kumann, John Hartfiel

  • Initial document.

...