Download PDF version of this document.

Table of Contents

Overview

The Trenz Electronic TEMB0005 is a carrier for the module TEM00005. The carrier is equipped with a LAN socket, a FTDI JTAG/UART to USB2.0 solution, three low speed and one high speed CRUVI B2B Connectors, a PMod Connector.

Refer to http://trenz.org/temb0005-info for the current online version of this manual and other available documentation.

Key Features

  • Modules
    • TEM0005
  • RAM/Storage
    • 2KB EEPROM
  • On Board
    • FT2232H FTDI
    • 4x User LEDs
    • 2x Push Buttons
    • 2x MEMS Oscillators
  • Interface
    • 1x Samtec Razor Beam (SS5) B2B Connector
    • 1x Samtec Razor Beam (SS4) High Speed CRUVI Connector
    • 3x Samtec Low Speed CRUVI Connectors
    • 1x PMod SMD (2x6) Connector
    • 1x SMD Header (1x6)
    • 1x RJ45 LAN Socket
    • 1x Micro USB2.0 Connector
  • Power
    • 5V Input Power Supply 
  • Dimension
    • 115 x 70 mm
  • Notes


Block Diagram

TEMB0005 block diagram

Main Components

TEMB0005 main components
  1. SMD Header 6x1, J3
  2. RJ45 LAN Socket, J1
  3. B2B Connector, J11
  4. Barrel Jack, J4
  5. Green LEDs, D1...4
  6. User Push Button, S2
  7. PMod 2x6 SMD Host Socket, J9
  8. FT2232H FTDI, U1
  9. Reset Push Button, S1
  10. Micro USB2.0 Socket, J2
  11. Red LED (PG_DCDC), D8
  12. Green LED (5VIN), D5
  13. High Speed CRUVI Connectors, J5
  14. Low Speed CRUVI Connectors, J8
  15. Low Speed CRUVI Connectors, J7
  16. Low Speed CRUVI Connectors, J6

Initial Delivery State

Storage device name

Content

Notes

EEPROMProgrammedFTDI Confirguration
Initial delivery state of programmable devices on the module

Configuration Signals

Signal

B2BConnected toNote
M_RESETJ11- 11Push Button, S1Module Reset
EN_VADJJ11-110DCDC, U6pull-down, input from module
SEL_VADJJ11-108DCDC, U6

pull-up, input from module.
'low' → 1.8V,
'high'→ 2.5V

Reset process.

Signals, Interfaces and Pins

Board to Board (B2B) I/Os

The carrier TEMB0005 is equipped with a Samtec (SS4) B2B Connector. More information in the following table.

DesignatorsInterfaceI/O Signal CountConnected toNotes
J11






JTAG4x Single EndedFTDI, U1
MSIOD24x Single Ended, 12x Differential PairsCRUVI B2B, J5A0...5, B0...5 (N/P)
MSIO/GPIO8x Single EndedCRUVI B2B, J6A_X0...7
MSIO8x Single EndedCRUVI B2B, J7B_X0...7
MSIO/GPIO8x Single EndedCRUVI B2B, J8C_X0...7
LEDs (2x MSIO, 2x MSIO/GPIO)4x Single EndedD1...4LED1...4
MSIO8x Single EndedPmod Header, J9
Push Button1x Single EndedPush Button, S1M_RESET
Push Button1x Single EndedPush Button, S2pull-up, User Button
MSIO/GPIO/I2C2x Single EndedCRUVI B2B J6I2C
ETH

2x Differential Pairs

2x Single Ended

RJ45 Socket, J1

RJ45 LEDs, J1


Yellow and Green LEDs

UART2x Single EndedFTDI, U1UART RX/TX
FTDI I/O2x Single EndedFTDI, U1BDBUS2-BDBUS3
CLK

1x Single Ended

Oscillator, U8

30 MHz

MSIOD

4x Single Ended

CRUVI B2B, J5

RESET, HSIO, HSO, HSI

IO (3x MSIO, 4x MSIO/GPIO, 2x MSIO GPIO/I2C)9x Single EndedCRUVI B2B, J5
Power Signal1x Single Ended

RED LED, D8


PG_DCDC
SC_SPI4x Single Endedpin header, J3SC_CLK, SC_SDO, SC_SDI, SC_SS
GOLDEN1x Single EndedTestpoint, TP1GOLDEN
JTAGSEL1x Single EndedTestpoint, TP2JTAGSEL
General B2B connectors information

CRUVI B2B Connectors

The TEMB0005 is equipped with three Low Speed Connectors J6...8 and a High Speed Connector J5. These connectors are provided for CRUVI extension cards. More information is provided in the  B2B Connectors section.

SpeedDesignatorsSchematicConnected toNotes
LowJ6A_X0...1B2B, J11alternative GPIO

A_X2...5B2B, J11alternative SPI

A_X6...7B2B, J11alternative I2C0 SDA/SCL
J7B_X0...7|B2B, J11
J8C_X0...7B2B, J11alternative GPIO
HighJ5A0...A5 (N/P)B2B, J11HS I/O
B0...B5 (N/P)B2B, J11HS I/O
HSIO, HI, HO, RESETB2B, J11HS I/O single ended

SMB_ALERT, SMB_SDA, SMB_SCL, MODE, REFCLK

B2B, J11
DI,DO,SCK,SELB2B, J11alternative GPIO
CRUVI B2B connectors information

USB2.0 Socket

There is a USB2.0 Socket, J2 provided in order to use JTAG/UART via FTDI, U1.

Pin SchematicConnected toNotes
IDN.CN.C
D+DL_PFTDI, U1Through Line Filter, L1
D-DL_NFTDI, U1Through Line Filter, L1
VbusVBUSDiode, U2
USB2.0 Socket information

RJ45 LAN Socket

There is a RJ45 Ethernet LAN Socket, J1 connected to B2B, J11 via 2x channels data receive and transmit.

Pin SchematicConnected toNotes
TD+ETH1_TX_PB2B, J11
TD-ETH1_TX_NB2B, J11
RD+ETH1_RX_PB2B, J11
RD-ETH1_RX_NB2B, J11
Green LEDETH1_LED0B2B, J11Link/Activity indicator
Yellow LEDETH1_LED1B2B, J11Speed indicator
RJ45 LAN Socket information

PMod Header

There is a PMod Header, J9 connected to the B2B, J11 and all signals are protected from invers polarity by two diodes D6, D7.

SchematicConnected toNotes
PM0...3 (N/P)B2B, J11
PMod Header information

Pin Header

There is a Pin Header 6x1, J3 provided for SPI signals. 

Pin SchematicConnected toNotes
13.3VB2B, J11
2GNDB2B, J11
3SC_SDOB2B, J11
4SC_SDIB2B, J11
5SC_SSB2B, J11
6SC_CLKB2B, J11
Pin Header connections

UART 

There is an UART channel provided in order to communicate with the module and signals are accessible via B2B, J11 through the FTDI, U1.

U1 PinSchematicConnected toNotes
BDBUS1UART1_TXDB2B, J11FTDI receiver input
BDBUS0UART1_RXDB2B, J11FTDI transmitter output
UART connection


JTAG Interface

JTAG access is provided through B2B connector J11 connected to the FTDI. For more information please refer to the FTDI section.

JTAG Signal

B2B Connector

TMSJ11-14
TDIJ11-8
TDOJ11-10
TCK

J11-12

JTAGSELJ11-9
JTAG pins connection

Test Points

Test PointSignalConnected toNotes
TP1GOLDENB2B, J11
TP2JTAGSELB2B, J11
TP3PG_DCDCB2B, J11Red LED, D8
TP4VADJRegulator, U6
TP5PROBE_BB2B, J11
TP6PROBE_AB2B, J11
Test Points Information

On-board Peripherals

Chip/InterfaceDesignatorNotes
FTDIU1
TEMB0005 TRM#LEDsD1...D6
Push ButtonsS1-S2
TEMB0005 TRM#EEPROMU3
Oscillator
U4, U8

On board peripherals

FTDI FT2232H

The FTDI chip (U8) converts signals from USB2 to variety of standard serial and parallel interfaces. Refer to the FTDI data sheet to get information about the capacity of the FT2232H chip which is used in  Multi-Protocol Synchronous Serial Engine (MPPSE) mode for JTAG. 

The configuration of FTDI FT2232H chip is pre-programmed on the EEPROM U10.

PinSchematicConnected toNotes
ADBUS0TCKFPGA Bank 1B, U6JTAG interface
ADBUS1TDIFPGA Bank 1B, U6
ADBUS2TDOFPGA Bank 1B, U6
ADBUS3TMS

FPGA Bank 1B, U6

BDBUS0F_UART_TXFPGA Bank 1B, U6UART transmitter output
BDBUS1F_UART_RXFPGA Bank 1B, U6UART receiver input
BDBUS2BDBUS2B2B,J11I/O
BDBUS3BDBUS3B2B,J11I/O
OSCIOSCIOscillator, U4Clock 12 MHz
EECSEECSEEPROM, U3EEPROM Contains FTDI configuration
EECLKEECLKEEPROM, U3
EEDATAEEDATAEEPROM, U3
DM/DPD_N/ D_PMicro USB, J2USB to UART
nRESET3.3V3.3V
FTDI chip interfaces and pins

EEPROM

There is an EEPROM IC, U3 provided for storing the FTDI (U1) configuration. 

PinSchematicNotes
DI/DOEEDATAData
CLKEECLKClock
CSEECSSelect
I2C EEPROM interface MIOs and pins

The I2C address is as the following.

I2C AddressDesignatorNotes
0x70U3
I2C address for EEPROM

Push Buttons

There are two Push Buttons provided on the TEMB0005 designated as S1, S2. The Push Button S2 is considered to be as user buttons and S1 is provided to reset the module on the carrier.

DesignatorSchematicConnected toFunctionalityNote
S1M_RESETB2B, J11Reset
S2ButtonBUTTONUser Button
On-board Push Buttons

LEDs

There are 4 green LEDs provided as user LEDs.

DesignatorColorConnected toActive LevelNote
D1...D4GreenB2B, J11Active HighUser LEDS
D5Green5VINActive HighPower Status LED
D6RedPG_DCDCActive Lowfrom module
On-board LEDs


Clock Sources

DesignatorDescriptionFrequencyNote
U4MEMS Oscillator12 MHz
U8MEMS Oscillator30 MHz
Osillators

Power and Power-On Sequence

Power Supply

Power supply with minimum current capability of 2 A for system startup is recommended.

Power Consumption

Power Input PinTypical Current
5VINTBD*
Power Consumption

* TBD - To Be Determined

Power Distribution Dependencies

Power Distribution

Power-On Sequence

Power Sequency

Power Rails

Power Rail Name

B2B Connector J11 Pin

CRUVI Connector J5 Pin

B2B Connector J6 Pin

B2B Connector J7 Pin

B2B Connector J8 PinDirectionNotes
3.3V1, 2, 3, 4-101010Output
VDAJ2236---Output
5VIN--121212Output
Module power rails.

Board to Board Connectors

Unable to render {include} The included page could not be found.

CRUVI B2B Connectors

CRUVI modules use on bottom side:
  • TMMH-106-04-F-DV-A-M as Low Speed connectors, (12 pins, 6 per row) 
  • ST4-30-1.50-L-D as High Speed connectors, (60 pins, 30 per row) 

CRUVI carrier use on top side: 

  • CLT-106-02-F-D-A-K as Low Speed connectors , (12 pins, 6 per row) 
  • SS4-30-3.50-L-D as High Speed connectors, (60 pins, 30 per row)
Connector Mating height

Mating height of the high speed connectors is 5mm. The low speed connectors mate correctly within a range from 4.78 mm to 5.29 mm.

Current Rating

Current rating of High Speed B2B connectors is 1.6A per pin (2 pins powered).

Current rating of Low Speed B2B connectors is 4.1A per pin (2 pins powered).

Speed Rating

There is no data available for the connectors actual used here. Data available for other stacking heights of same connectors is summarized in the folllowing table:

ConnectorSpeed ratings
ST4/SS4 single ended (4mm stacking height!)13.5GHz / 27 Gbps
ST4/SS4 differential (4mm stacking height!)15.5 GHz / 31 Gbps
TMMH/CLT single ended (4.77mm stacking height!)5.5GHz / 11 Gbps
Connector speed ratings
Operating Temp Range

All connectors are specified for a temp. range of -55 °C to 125 °C.

Technical Specifications

Absolute Maximum Ratings

SymbolsDescriptionMinMaxUnit
VINInput Supply Voltage2.534V
T_STGStorage Temperature-55125°C
PS absolute maximum ratings

Recommended Operating Conditions

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

ParameterMinMaxUnitsReference Document
VIN4.065.58VSee the carrier datasheets.
T_OPT070°CPush button datasheet.
Recommended operating conditions.

Physical Dimensions

  • Module size: 115 mm × 70 mm.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 4 mm.

PCB thickness: 1.6 mm.

Physical Dimension

Currently Offered Variants 

Trenz shop TEMB0005 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History


DateRevisionChangesDocumentation Link
2020-05-20REV01

Initial Release

---
Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Board hardware revision number.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • Initial Release

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • No labels