Chip/Interface | IC | PS7 Peripheral | |
---|---|---|---|
SPI Flash | S25FL127SABMFV10 | QSPI0 | 16MByte Flash |
I2C EEPROM | 24xx64 | I2C0 | 8KByte EEPROM |
RTC | RV-3029 | I2C0 | |
RTC Interrupt | GPIO - MIO0 | ||
User LED | GPIO - MIO7 |
Mapping table for on-board IC to PS7 Peripherals
MIO Pin | Mapped to | Pull up/down | Notes |
---|---|---|---|
0 | GPIO | Up | RTC Interrupt |
1 | QSPI0 | ||
2 | QSPI0 | Down | |
3 | QSPI0 | Down | |
4 | QSPI0 | Down | Override to up on base for bootmode change |
5 | QSPI0 | Up | |
6 | QSPI0 | Down | |
7 | GPIO | Down | On-board LED |
8 | CAN1 TXD | Down | CAN transceiver in SBC |
9 | CAN1 RXD | CAN transceiver in SBC | |
10 | SPI1 MOSI | SBC SPI Bus | |
11 | SPI1 MISO | SBC SPI Bus | |
12 | SPI1 SCLK | SBC SPI Bus | |
13 | SPI1 SS0 | SBC SPI Bus | |
14 | I2C0 SCL | Up | On-board RTC, and EEPROM |
15 | I2C0 SDA | Up | On-board RTC, and EEPROM |
Recommended Peripheral mapping for MIO Voltage bank 0.
There is no fixed mapping for PS7 UART, if needed it can be mapped to free pins from MIO1 Bank or via EMIO to PL pins.
Recommended mapping for primary (console, debug) UART are MIO52, MIO53 for all cases when MIO1 is not used for of-board Gigabit ETH PHY.
Both Ethernet PHY IC's are connected to PL pins in Bank 34, all PHY IC pins are connected to FPGA pins, there is no sharing of signals for the two PHY's.
PUDC pin is connected with pull-up to 3.3V those pre-configuration pull-ups are disabled by default. Strapping resistor exist to change the PUDC mode.
Bank | VCCIO | B2B I/O Pins | Notes |
---|---|---|---|
500 | 3.3V | 0 | |
501 | USER J2.4 B2B | 36 | MIO1 VREF is connected to resistor divider to support HSTL18 |
13 | USER J1.39 B2B | 48 | Differential routing |
33 | 3.3V | 33 | Single ended routing |
34 | 3.3V | 0 | Ethernet PHY's |
35 | 3.3V | 42 | Single ended routing |
0 | 3.3V | 4 | JTAG, note 3 pins can be used as input only from PL Fabric |
IC | Description | Frequency | Used as |
---|---|---|---|
U14 | MEMS Oscillator | 33.3333MHz | PS7 PLL clock |
U5 | MEMS Oscillator | 25MHz | Ethernet PHY Clock |
U7 | RTC (internal oscillator) | 32.768KHz | Used by RTC, CLKOUT of RTC not connected |
Designator | Color | Connected to | Active Level | IO Standard |
---|---|---|---|---|
D9 | Green | DONE | Low | not applicable |
D8 | RED | MIO7 | High | not applicable |
D4 | Green | PL pin V18 | High | LVCMOS33 |
XADC Pin | Connected to | Notes |
---|---|---|
VP_0 | SBC MUX_OUT | Resistor divider to adjust ADC Range |
VN_0 | GND | |
AD0 | B2B | |
AD1 | B2B | |
AD3 | B2B | |
AD4 | B2B | |
AD5 | B2B | |
AD7P | B2B | |
AD7N | GND | |
AD8 | B2B | |
AD9 | B2B | |
AD10 | B2B | |
AD12 | B2B | |
AD13 | B2B | |
AD14 | B2B | |
AD15 | B2B |
XADC is used with internal reference option.
Note the XADC capable pins are not routed differentially to the B2B connector. The performance and usability of the XADC must be evaluated.
There are two 100Mbit Extreme Temperature Ethernet PHY's DP83848YB on the board. Datasheet is available from TI, Literature number SNLS208H. Both PHY's are connected with all I/O Pins to FPGA Bank 34 (VCCIO = 3.3V). PHY Clock 25MHz source is provided from MEMS Oscillator. All LED outputs have on-board pull-ups. Outputs to Magnetics have also required termination resistors on board.
Both PHY's must be operated in MII Mode, other modes are not supported. It is possible to use PS ENET0 or ENET1 via EMIO routing or Ethernet IP Cores implemented in PL Fabric.
ETH1 | ETH2 | Pullup | Notes | |
---|---|---|---|---|
CTREF | J3.57 | J3.25 | Magnetics center tap voltage | |
TD+ | J3.58 | J3.28 | on-board | |
TD- | J3.56 | J3.26 | on-board | |
RD+ | J3.52 | J3.22 | on-board | |
RD- | J3.50 | J3.20 | on-board | |
LED1 | J3.55 | J3.23 | on-board | |
LED2 | J3.53 | J3.21 | on-board | |
LED3 | J3.51 | J3.19 | on-board | |
POWERDOWN/INT | L21 | R20 | on-chip | It is recommended to configure FPGA I/O as input with Pullup or as output driving 1 if Interrupt not used. |
RESET_N | M15 | R16 | on-chip | It is recommended to configure FPGA I/O as input with Pullup or as output (active low PHY Reset). |
Date | Revision | Authors | Description |
---|---|---|---|
2015-05-10 | Work in progress | ||
All |